WELLTECH WellGate 2880 User manual

WellGate 2880, 8 ports FXO
Gateway User Guide
Version: 1.01
Date: 2015/07

2
Contents
CH1 Introduction.................................................................................... 4
1-1 Physical Interface ............................................................................. 4
1-2 IP Network connection ..................................................................... 5
1-3 Front Panel: LED Indicators.......................................................... 5
1-4 Rear Panel: Cable connections ...................................................... 6
1-5 QUICK SETUP ................................................................................ 6
CH2 Device Settings ............................................................................. 12
2-1 Network Configuration................................................................... 12
2-2 Device Time Setting ....................................................................... 14
2-3 Device Advance Setting.................................................................. 16
2-4 User Login Setting.......................................................................... 17
2-5 Debug Settings................................................................................ 18
2-6 Event Notice................................................................................... 19
2-7 Auto Provision................................................................................ 19
2-8 SNMP ............................................................................................. 20
CH3 NAT Setting................................................................................... 22
3-1 DHCP Ser. (DHCP server).............................................................. 22
3-2 UPnP (universal plug and play server)........................................... 23
3-3 Bandwidth (Bandwidth Control).................................................... 23
3-4 URL Filter....................................................................................... 27
3-5 IP Filter........................................................................................... 27
3-6 MAC Filter ..................................................................................... 27
3-7 APP Filter........................................................................................ 28
3-8 Port Filter........................................................................................ 28
3-9 Port Fwd ......................................................................................... 29
CH4 VOIP Setting.............................................................................. 30
4-1 SIP parameters setting .................................................................... 30
4-2 Audio .............................................................................................. 32
4-3 Tone ................................................................................................ 34
4-4 NAT Traversal................................................................................. 35
CH5 VOIP Advance .............................................................................. 36

3
5-1 SIP .................................................................................................. 36
5-2 Audio .............................................................................................. 39
5-3 Ring ................................................................................................ 40
CH6 Dialing Plan................................................................................. 41
6-1 General............................................................................................ 41
6-2 Dialing Rule.................................................................................... 42
6-3 Digit Manipulation ......................................................................... 43
6-4 Phone Book..................................................................................... 44
CH7 CO Setting .................................................................................... 45
7-1 FXO line ......................................................................................... 46
CH8 SIP Trunk...................................................................................... 48
8-1 Create SIP Trunk............................................................................. 49
CH9 Route Plan.................................................................................... 51
9-1 Create Route Plan........................................................................... 52
CH10 Status .......................................................................................... 54
10-1 Device States ................................................................................ 54
10-2 Line States .................................................................................... 54
10-3 SIP Trunk States............................................................................ 55
CH11 Maintenance ............................................................................... 56
11-1 Firmware Update .......................................................................... 56
CH12 Logout......................................................................................... 57
Appendix A --- System Recovery......................................................... 57
Appendix B --- HTTP auto provisioning.............................................. 60
Appendix C --- SNMP.......................................................................... 62

4
WellGate 2880
CH1 Introduction
WellGate 2880 Analog SIP Gateway
WellGate 2880 is a 8 ports FXO VoIP gateway which includes 1-WAN/1-LAN
(management port) 10/100 base-T network environment. Field-proven
quality of Voice communication and Fax transmission over IP broadband
access network to makes WellGate 2880 to be an excellent solution for various
VoIP applications.
The core firmware and webpage configuration is consistent with both 4-port
FXO gateway (WellGate 2540) and 24-port FXO gateway (WellGate 2424O).
So, there is not any difficulty to use WellGate 2880 if you are already using
WellGate 25xx or WellGate 24xx series gateway. Besides, if you have
established HTTP provision to manage Wellgate 2504, it should be able to
manage this device as well.
1-1 Physical Interface
Ethernet port (RJ-45, 10/100 base-T)
1-WAN port, for connect to router, ADSL modem (ATU-R), or switch
hub directly. This port is used to connect SIP network for VoIP call.
1-LAN port, for PC management or other network devices
connecting. This port provide DHCP server and used to configure
this gateway.
Telephony port (RJ-11)
8-FXO ports, to connect to PSTN lines two wire tip/ring.
DC power Jack
Status indicated LED
Indicates Power, Ethernet, Line, SIP Proxy registration status
AC to DC Power Adaptor:
- INPUT: AC100V-240V, 50/60Hz
- OUTPUT: DC 12V, 3A

5
1-2 IP Network connection
IPv4 (RFC 791)/IPV6 (RFC 2460)
IPv6 Auto Configuration (RFC 4862)
MAC Address (IEEE 802.3)
Static IP
DHCP Client (RFC 2131)
PPPoE
DNS Client
TCP/UDP (RFC 793/768)
RTP/RTCP (RFC 1889/1890)
IPV4 ICMP (RFC 792)/IPV6 ICMP (RFC 4443)
TFTP Client
VOIP VLAN Support (802.1q/802.1p)
HTTP/HTTPS Server
QoS Support
Support IPV4 only, IPV6 only or dual stack mode
1-3 Front Panel: LED Indicators
WellGate 2880
Figure 1-3-1 front panel
LED
Description
Power
When the power adapter is connected, the LED will light
up green.
Proxy
When the gateway is registered successfully to SIP Proxy
or IP-PBX, this LED will light up green.
WAN
This LED will light up green when the gateway’s WAN port
is physically connected to IP Ethernet. When data is
transmitted through this port, it will flash green.
The default IP of WAN port is 10.1.1.3.
LAN
This LED will light up green when the gateway’s LAN port
is physically connected to a local IP network (Refer to Rear

6
Panel section for location of LAN port). When data is
transmitted through this port, it will flash green.
The default IP of LAN port is 192.168.123.123.
1 to 8
The status LED for FXO port 1-8, these LEDs will light up
amber orange when the connected phone is engaged in a
conversation. It will flash amber orange when there is an
incoming call.
Note: The Line LED will flash slowly while there is not any
PSTN line connected at FXO port.
1-4 Rear Panel: Cable connections
WellGate 2880
Figure 1-4-1 rear panel for FXO gateway
Item
Description
1 –8
These 8 RJ-11 connectors are used to connect with local
PSTN line or analog extension of conventional PBX. The
RJ-11 connector color should be Gray.
LAN
10/100 Base-T RJ-45 socket for LAN port, connects to PC
for management purpose only. The default is DHCP
Server.
WAN
10/100 Base-T RJ-45 socket for WAN port, connects to
SIP IP network for VoIP call purpose.
DC 12V
The power socket, input AC 100V~240V; output DC12V,
3A
Caution:
When this product is interfered with static electricity, please restart your device,and you can continue to use in normal.
1-5 QUICK SETUP
Note:
Please use Windows IE 9.0 web browser or above version to
configure FXO gateway webpage setting. Make sure to adjust
low level safety of IE browser. Welltech products don’t support

7
other Web Browser such as FireFox or Google Chrome to
configure. Otherwise, the configuration from webpage can’t be
saved successfully.
Login :
Setp1: Setup the administrative PC’s IP to DHCP mode and connects RJ-45
Ethernet cable between LAN port and computer. Start IE 9 (or later version) to
navigate Wellgate 2880 web management system by typing the default URL
which is http://192.168.123.123 (through LAN port) or http://10.1.1.3
(through WAN port). The screen will display User Name and Password (the
default user ID is root and user password is root). (See figure 1-5-1 web
access)
Figure 1-5-1 web access
Step 2: After login, the screen shows the Home page of Wellgate 2880. (See
figure 1-5-2 Network configure-1)

8
Figure 1-5-2 Network configure-1
Change Default IP Network:
Step 3: After successfully login to the system, we need to change the network
configuration. Click Device Setting > Network to set up the service network
interface (WAN) parameters. Enter IP address, Subnet mask and default
gateway or selected to “DHCP” or “PPPOE”. Apply the change by clicking
Apply button as figure (See Figure 1-5-3 Network configure-2).
Note: If Gateway WAN port are setting in the 10.x.x.x segment, please make
sure that you need to change the LAN port to other segment such as
192.168.x.x in order not to conflict IP between WAN and LAN.

9
Figure 1-5-3 Network configure-2
Change Default Time setting:
Step 4: When re-login to the new IP address, the next is to setup the system
time zone. Click Device Setting > Time to setup the system. Enter the
current SNTP server, time zone and daylight saving parameters. Apply the
change by clicking Apply button. (See figure 1-5-4 Time setting)
Figure 1-5-4 Time setting
Modify SIP Account Parameter:
Step 5: The next step is to add a SIP Trunk for VOIP calling. For WellGate 2880,
it is necessary for VOIP calling. Click SIP Trunk and new to create the
required SIP trunk. Enter the trunk ID to 1 and enter those SIP parameters.
Apply the change by clicking Apply button. (See Figure 1-5-5 SIP Trunk)

10
Figure 1-5-5 SIP Trunk
Note: Please don’t delete SIP Trunk, even it is not used. Because Route Plan
feature needs to use SIP Trunk.
Soft Reset WellGate 2880:
Step 6: After modify basic setting, it is required to reset WellGate 2880. Click
Maintenance > Maintenance > Quick-Reset or Reboot to take effect.
Apply the change by clicking Apply button. (See Figure 1-5-6 Quick-Reset)
Figure 1-5-6 Quick-Reset
Check WellGate 2880 Registered Status:
Step 7: After Quick-Reset or reboot, Click Status > SIP Trunk Status to
check whether registered or not. (See figure 1-5-7 SIP trunk status)
Figure 1-5-7 SIP trunk status
Through the above settings, WellGate 2880 should be able to do the following:
1. For PSTN incoming call, the caller will hear a dial tone after WellGate 2880
answer this call. Then the caller can dial a VoIP number which can be used
by SIP Trunk 1 table to make SIP call out. This is an example of 2 stage
dialing.

11
2. For VoIP incoming call from WAN port, WellGate 2880 will select a FXO
port and dial number to PSTN network via this FXO port.

12
CH2Device Settings
From this setting category, all devices related parameters can be found here.
2-1 Network Configuration
> Network
Figure 2-1 network setting
Parameter Description:
Setting:
IP Support: IP stack to be supported (IPV6 and IPV4 or IPV6 or IPV4
only).
WAN Setting:
Network Type: support “Fixed IP”or ”DHCP”or ”PPPoE”
IP Address:Enter IP address if you select Fixed IP.
Default Gateway: Default gateway.
DHCP Tag (option 60): Vendor class identifier or not.
DHCP Tag (option 61): Client identifier or not.
DNS Server1: Primary DNS Server IP network.
DNS Server2: Secondary DNS Server IP network.

13
VOIP VLAN: Enable VOIP VLAN or not. When enable VOIP VLAN, the
WAN port can be only accessed by VLAN. If it is required to manage the
WellGate 2880, Administrator can use LAN port instead.
VOIP VLAN ID(2-4096): VLAN ID Used.
Note: the default WAN IP address is 10.1.1.3.
LAN Setting:
Management mode: This LAN port is used for management purpose,
not used for register or routing.
NAT mode: DHCP function on the LAN port. The LAN port functions as a
DHCP server, network devices connected to them will be issued with
IP addresses. (On the lift item will add a NAT setting, the information
please refer NAT setting)
IP Address:IP address (please set to 192.168.x.x if your WAN port is
using 10.x.x.x IP segment, the IP segment must be different with
WAN IP).
Netmask: IP network mask
Bridge mode: At this mode, both WAN and LAN ports are configured to
Switch/Hub features. LAN port access to WAN port directly.
Note: default LAN IP address is 192.168.123.123
DDNS (DynDNS) Setting:
DDNS (DynDNS): enable or disable dynamic DNS feature.
Domain Name: input your Domain Name
User Name: input your user name
Password: input your password

14
2-2 Device Time Setting
WellGate 2880 support SNTP with time zone and daylight saving.
Device Setting > Time
Figure 2-2 Time setting
Parameter Description:
Current Time: display time now (display only).
NTP Time Server: SNTP time server which provide current time from
network.
NTP Refresh Interval(sec):The frequency to sync NTP server in
seconds.
Time Zone: The time-zone (base on GMT time) Wellgate 2880 is
located.
-Standard: Use a predefined standard time zone.
-Customize: Use a user defined time zone.
Daylight Saving: Auto adjust daylight saving timer or not
Daylight Bias: The offset added to the Bias when the time zone is in
daylight saving time
Daylight Start: The date that a time zone enters daylight time
-Month: 01 to 12
-Week Day: Sunday to Saturday
-Apply Week (Day:01 to 05, Specifies the occurrence of day in the
month; 01 = First occurrence of day, 02 = Second occurrence of
day, ...and 05 = Last occurrence of day)
-Hour: 00 to 23
Standard Start: The date that a time zone enters daylight time
-Month: 01 to 12
-Week Day: Sunday to Saturday
-Apply Week (Day:01 to 05, Specifies the occurrence of day in the
month; 01 = First occurrence of day, 02 = Second occurrence of
day, ...and 05 = Last occurrence of day)

15
-Hour: 00 to 23

16
2-3 Device Advance Setting
> Advance
Figure 2-3 Advance setting
Parameter Description:
HTTP Service: The Administrator Web service port (the default is 80)
HTTPS Service: The https web service port (the default is 443)
Telnet Service: The telnet service port (the default is 23)
HTTP/HTTPS Service access on WAN: When click the disable option;
The WEB service will be rejected on WAN port, so please be careful with
this function. If you wanted to enable WAN port again, you need to
access this device from its LAN port to connect to WEB pages and enable
WAN port.

17
2-4 User Login Setting
Three level of users can be used, administrator, supervisor and user. Each
level of users will have different predefined access level.
>User Login
Figure 2-4 user login setting
Parameter Description:
Administrator: The administrator level user which has full access of
Wellgate 2880.
Supervisor: The supervisor level user which has limited administrative
access right.
User: The user access right which only allows to setting some user
related features.
User ID: Login User ID
Password: Login Password
Confirm Password: Confirm new password again
Language: The web page language used when the account login. To add
a customized local language, please contact Welltech.

18
2-5 Debug Settings
Wellgate 2880 provides the real time debug to syslog or through Telnet interface. It
generates the debug information based on debug level and modules. Since the
generating debug will consume system resource, it is recommended to turn on only for
necessary and under Welltech FAE’s instruction.
Debug
Figure 2-5 Debug setting
Parameter Description:
SYSLOG: Enable or disable to send system information to SYSLOG
server or not
Check for start from Any Time: Always Send: Always send syslog or
only during a specified time range.
Syslog Start (YYYY/MM/DD HH:MM): Always Send: Always send
syslog or only during a specified time range.
Syslog Stop (YYYY/MM/DD HH:MM): The syslog stop sending time.
Syslog Server: Syslog server IP address
Syslog Port: syslog server service port (default is 514)
DSP Debug: Enable or disable to send DSP information to capture log
DSP Capture server: Syslog capture server IP address
DSP Capture port: syslog capture server service port (default is 50000)

19
2-6 Event Notice
Wellgate 2880 can send Syslog Event Notice when it had the following cases:
1. Register Failure or re-registered
2. FXO RJ-11 cable was plugged or unplug
3. Ethernet reconnected
4. System started
Figure 2-6 Event notice setting
Syslog Notice: Enable or disable to send system event to SYSLOG
server or not.
Syslog Server: Syslog server IP address.
Syslog Port: syslog server service port (default is 514).
2-7 Auto Provision
Wellgate 2880 can be provisioned by HTTP Server for mass deployment.
>Provisioning
Figure 2-7-1 Provisioning
Select Http:
This feature is for feature usage only.
Figure 2-7-2 Provision type of Http

20
Http config URL: internal used only
Refresh interval(minute): The interval to check if there is a new
configuration/firmware or not (in minutes).
User ID: specify the login ID for http authentication.
Password: specify the password for http authentication.
2-8 SNMP
Figure 2-8 SNMP
SNMP Agent:
SNMP Agent: Enable SNMP or not.
Read Only Community Name: The community name to read
through SNMP protocol.
Read Write Community Name: The community name to read and
write through SNMP protocol.
SNMP Agent Access on WAN: Enable SNMP to be accessed
through WAN port or not.
Trusted Peer:
Type:
Any Address: Any address can retrieve the SNMP
information.
Specify an IP Address: Only the IP address listed can
retrieve the SNMP information. Normally, it will be the SNMP
manager IP address.
Specify a Subnet: Only the network specified can retrieve
the SNMP information.
IP address: The IP address for a trusted peer.