Wenger AcoustiCabinet User manual

Seismic Installation
Cabinet Storage Products
©Wenger Corporation 2019 Printed in USA 2019-09 Part #145R422-04
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: [phone] • wengercorp.com
Note: Please read and understand these instructions before installing.
Note: Refer to the illustrations on the following pages.
If you need additional information, contact the Wenger Corporation using the information below.
Standard Acousti
Wall Anchor
See pages 2-4
UltraStor®Storage Cabinet
Section View
AcoustiCabinet®
Section View
Floor Anchor
See page 5
7'0"
(2134 mm)
Standard Acousti
7'0"
(2134 mm)
Floor
Floor
6'11"
(2108 mm) 7'4"
(2235 mm)
Seismic Instructions to be used with Wenger Storage Cabinets only!
For more detailed product information, refer to the Assembly Instructions 250B394.
Inferior or improperly installed fasteners
could cause the lockers to tip over.
!WARNING
Wall Anchor
See pages 2-4
Floor Anchor
See page 5

2
Wall Anchoring with C.M.U. Bracing
Wall Anchor - C.M.U. Bracing
AcoustiCabinets
C.M.U.
Support Wall
Wenger Part No. 255A502
Wall Bracket
Wenger Part No. X003492 Screw Anchors should be secured using the following procedure:
1. Use a 3/8" drill bit to pre-drill each hole 1/2" to 1" (13 to 25 mm) deeper into the wall surface
than the screw anchor length (to allow for dust and debris while drilling).
2. Remove any debris residue from the pilot hole.
3a. For Ultrastor only, drive the screw anchor through the back of the cabinet and into the pilot hole.
3b. For AcoustiCabinets only, drive the screw anchor through the 255A502 wall bracket and into the pilot hole.
4. Tightenthescrewanchortothespeciedtorque.
Wall Anchor - C.M.U. Bracing
UltraStor
C.M.U.
Support Wall
Wenger Part No. X003492
Simpson Screw Anchor (THD37400H)
Install Per ICC-ES ESR-2713
Min. C.M.U. Thickness of 3-3/4" (95 mm)
Embedment Depth of 2-1/2" (64 mm)
Min C.M.U. Thickness of 5" (127 mm)
Embeddment Depth of 3-1/4" (83 mm)
Torque 50 ft-lb (68 Nm)
(Two Required Per Cabinet)
Wenger Part No. X003492
Simpson Screw Anchor (THD37400H)
Install Per ICC-ES ESR-2713
Min. C.M.U. Thickness of 3-3/4" (95 mm)
Embedment Depth of 2-1/2" (64 mm)
Min C.M.U. Thickness of 5" (127 mm)
Embeddment Depth of 3-1/4" (83 mm)
Torque 50 ft-lb (68 Nm)
(Two Required Per Cabinet)

3
Wall Anchoring with 2" x 6" Wood Bracing
Wall Anchor - 2" x 6" Wood Bracing
UltraStor
Stud Support Wall Studs @
16" On-Center Max.
1/2"
Sheet Rock
Wenger Part No. X002159
#12 F.W.W. Screw 3-1/2" LG @ 16" On-Center
Min. Penetration 1-1/2" (38 mm)
Into Solid Wood Blocking
(Two Required Per Cabinet)
2" x 6" Blocking
@ All Cabinets, Shelving,
Tackboards, Chalkboards, Ect.
(Supplied By Contractor)
Wall Anchor - 2" x 6" Wood Bracing
AcoustiCabinets
Stud Support Wall Studs @
16" On-Center Max.
1/2"
Sheet Rock
Wenger Part No. X002159
#12 F.W.W. Screw 3-1/2" LG @ 16" On-Center
Min. Penetration 1-1/2" (38 mm)
Into Solid Wood Blocking
(Two Required Per Cabinet)
2" x 6" Blocking
@ All Cabinets, Shelving,
Tackboards, Chalkboards, Ect.
(Supplied By Contractor)
Wenger Part No. 255A502
Wall Bracket

4
Wall Anchoring with Metal Stud Bracing
Wall Anchor - Metal Stud Bracing
UltraStor
Stud
Support Wall
18 Ga. G.S. Unpunched "C" Stud
Backing Cont. @ All Cabinets,
Shelving, Tackboards,
Chalkboards, Ect.
(Supplied By Contractor)
1/2"
Sheet Rock
Wenger Part No. X002456
Screw, Drill/Tap 1/4-14 x 3" @ 16" On-Center
(Two Required Per Cabinet)
18 Ga. Steel Studs
@ 16" On-Center Max.
Wall Anchor - Metal Stud Bracing
AcoustiCabinets
Stud
Support Wall
1/2"
Sheet Rock
Wenger Part No. X002456
Screw, Drill/Tap 1/4-14 x 3" @ 16" On-Center
(Two Required Per Cabinet)
18 Ga. G.S. Unpunched "C" Stud
Backing Cont. @ All Cabinets,
Shelving, Tackboards,
Chalkboards, Ect.
(Supplied By Contractor)
Wenger Part No. 255A502
Wall Bracket
18 Ga. Steel Studs
@ 16" On-Center Max.

5
Floor Anchoring
Floor Anchor
All Cabinets Except Cabinet #41
Front of
Cabinet
Wenger Part No. X003498
Hilti KB-TZ (KB-TZ 3/8 x 3-3/4")
Kwik Bolt TZ Expansion Anchor
2" (51 mm) E󰀨ective Minimum
Embedment Into Floor
Torque 25 ft-lb (34 Nm)
(Two Required Per Cabinet)
145L459 Bracket
Typ. Both Sides
(Two Per Cabinet)
Wenger Part No. X000045
#8-15 x 5/8" Pan Head
Four Screws Per Bracket
(Eight Per Cabinet)
Leveler
Bracket
Wenger Part No. X003498 Expansion Anchors should be secured using the following procedure:
1. Usea3/8"drillbittopre-drilleachhole1/2"to1"(13to25mm)deeperintotheoor
than the expansion anchor length (to allow for dust and debris while drilling).
2. Remove any debris residue from the pilot hole.
3. Drivetheexpansionanchorthroughthe145L459or145R486oorbracketandintothepilothole.
4. Tightentheexpansionanchortothespeciedtorque.
Floor Anchor
For Cabinet #41
Wenger Part No. X003498
Hilti KB-TZ (KB-TZ 3/8 x 3-3/4")
Kwik Bolt TZ Expansion Anchor
2" (51 mm) E󰀨ective Minimum
Embedment Into Floor
Torque 25 ft-lb (34 Nm)
(Two Required Per Cabinet)
145R486 Bracket
Typ. Both Sides
(Two Per Cabinet)
Wenger Part No. X000045
#8-15 x 5/8" Pan Head
Four Screws Per Bracket
(Eight Per Cabinet)
Bottom
Frame
Front of
Cabinet

6
This page is intentionally blank.

7
This page is intentionally blank.

8
This page is intentionally blank.