Wenger Music Desk User manual

Assembly Instructions
Music Desk
for the Wenger Percussion Cabinet
Note: Please read and understand these instructions before assembling the parts.
Note: Remove all items from the shipping cartons and arrange them in a convenient location.
Refer to the illustrations on the following pages.
If you need additional information, contact Wenger Corporation using the information below.
CONTENTS
©Wenger Corporation 2012 Printed in USA 08/12 Part #147H156-02
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 1-800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Fastener Parts ist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Replacement Parts ist . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Music Desk Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2
IMPORTANT USER INFORMATION
GENERAL
Copyright © 2012 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in
any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser's personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that might
occur. The end user must exercise caution and common sense when assembling or installing Wenger
Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-887-7145.
MANUFACTURER
The Music Desk is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
1-800-4WENGER (493-6437) • 1-507-455-4100
www.wengercorp.com
INTENDED USE
•This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
•This product is intended to be assembled and used only as described in these instructions.
WARRANTY
This product is guaranteed free of defects in materials and workmanship for ten full years from
date of shipment. A full warranty statement is available upon request.

3
REQUIRED TOOLS
The following tools must be available to assemble the Music Desk:
• Rubber Mallet
• Phillips-Head Screwdriver
• Variable Speed Drill (to drive hex socket screws)
• 5/32” Hex Insert Bit (supplied).
BEFORE YOU BEGIN
•Read the complete assembly procedure before you begin.
•Remove all items from the shipping carton and lay them out approximately in their final position.
•Remove all items from the hardware bag and determine where all of the fasteners will be used.
FASTENER PARTS LIST
Hex Socket
Cap Nut #10-24
6
Washer, 3/8" ID
5
Wood Dowel
1
Wood Screw, 1/4x 2”
(color matches hinge color)
2
Machine Screw
#10 - 24 x5/8"
3
REPLACEMENT PARTS LIST
Item Description Item Description
1 Wood Dowel 5 Washer, 3/8” ID
2Wood Screw, 1/4x 2” (color matches hinge color) 6 Hex Socket Cap Nut #10 - 24
3Machine Screw #10 - 24 x 5/8" 7 Desk Panel
4 Desk Pivot Bracket 8 Tray Panel
MUSIC DESK ASSEMBLY
1. Tap the two Wood Dowels (1) into the indicated
holes on the edge of the Desk Panel (7). (Detai A)
2. Slip the Tray Panel onto the Wood Dowels.
Attach the panels together with five Wood Screws
(2), and tighten with the Hex Insert Bit. (Detai B)
Detai A
1
7
7
Detai B

4
MUSIC DESK ASSEMBLY (CONTINUED)
3. Turn the assembled Music Desk upside down,
and rest it on top of the Percussion Cabinet.
4. Attach a Desk Pivot Bracket (4) at one end
of the Desk Panel (7) with two Machine
Screws (3).and two hex socket cap nuts (6).
(Detai C)
5. Slip a Washer (5) onto the outside end
of the Desk Pivot Bracket (4) .(Detai D)
6. Insert the end of the Desk Pivot Bracket
into the hole in the Percussion Cabinet’s top bracket.
7. Slip the remaining Washer (5) onto the other
Desk Pivot Bracket (4). (Detai E)
8. Insert the Desk Pivot Bracket through the hole in the
top bracket on that side of the Percussion Cabinet.
9. Attach the Desk Pivot Bracket to the Music Desk with
the remaining two Machine Screws (3) and two hex
socket cap nuts (6). (Detai F)
4
3
6
7
Back of Cabinet
5
Detai C
Detai D
Detai E
Detai F
4
5
4
3
6
Back of Cabinet
Back of Cabinet