Wenger UltraStor Cover Panel User manual

nstallation nstructions
Ultra tor™ Cover Panel
Note: Please read and understand these instructions before assembling the parts.
Note: Remove all items from the shipping cartons and arrange them in a convenient location.
Refer to the illustrations on the following pages.
f you need additional information, contact Wenger Corporation using the information below.
CONTENTS
mportant User nformation . . . . . . . . . . . . . . . . . . . . . . . . . . .2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
ntended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Fastener Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cover Panel nstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
End Cover Panel nstallation . . . . . . . . . . . . . . . . . . . . .4
Center Cover Panel nstallation . . . . . . . . . . . . . . . . . . .7
Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
©Wenger Corporation 2015 Printed in USA 12/15 Part #250C880-02
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: [phone] • www.wengercorp.com

2
IMPORTANT USER INFORMATION
GENERAL
Copyright © 2015 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in
any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser's personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
n no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that might
occur. The end user must exercise caution and common sense when assembling or installing Wenger
Corporation products. f any questions or problems arise, call Wenger Corporation at 1-800-887-7145.
MANUFACTURER
The Cover Panel is manufactured by:
Wenger Corporation
555 Park Drive, Owatonna, MN 55060
(800) 4WENGER (493-6437) • [phone]
INTENDED UE
•This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
•This product is intended to be assembled and used only as described in these instructions.
WARRANTY
This product is guaranteed free of defects in materials and workmanship for ten full years from
date of shipment. A full warranty statement is available upon request.

3
REQUIRED TOOLS
The following tools must be supplied by the installer to install the Wenger Cover Panel:
•Drill
•3/16” Drill Bit
•3/8” Drill Bit
•#2 Philips Screwdriver (7” overall length max)
•5/32” Hex Driver (7” overall length max)
•Power Driver with #2 Bit (7” overall length max)
•Power Driver with 5/32 Hex Bit (7” overall length max)
•Non-marring Clamps (2)
•Hammer
•Tape Rule
FASTENER PARTS LIST
Screw, Machine, 1/4-20 x 2.359” (2)Screw, Wood, #8 x 1-3/8” (12)
Plastic Guide Tack (2)
Screw, #8 x 1-1/4” (1)
End Cover Extrusion (1)
nsert, Nut, 1/4-20 x 2.359” (4)

4
COVER PANEL INSTALLATION
END COVER PANEL IN TALLATION
1. With the package laid flat, carefully remove the
Cover Panel from the package and insert the two
Plastic Glide Tacks into the bottom of the Cover Panel,
centered and 2-3” from each end.
2. Lift the Cover Panel horizontally resting it on the back edge.
Attach the End Cover Extrusion to the bottom front edge of the
Cover Panel using a #8 x 1-1/4" Screw.
3. Lift the Cover Panel to a vertical position and fit it into place
over the exposed hardware.
Use the Plastic Glide Tacks to protect the bottom of the
Cover Panel.
The Cover Panel should fit flush against the front and
top sides of the cabinet.
Verify that the correct End Cover (LH or RH) matches
the side of the cabinet that it is being installed on.
4. Lay the Cover Panel back down onto the packaging.
Notches
Match

5
COVER PANEL INSTALLATION CONTINUED
5. Using the 3/16” drill bit, drill 12 holes
(9 holes for 68” tall cabinets) into the side panel
of the cabinet to be covered.
NOTE: Do not drill into a shelf or cross member.
Measure before drilling so that the hole is 1-2”
from the nearest horizontal surface to allow
clearance for tools.
Top Row
Drill a hole 2-3” down from the top and 2-3”
back from the front of the cabinet.
Drill the second hole 2-3” down from the top
and 24-26” (14-16” for 19-1/4” deep cabinets)
from the front of the cabinet.
Drill a third hole 2-3” down from the top and
evenly spaced horizontally between the first
two holes.
Bottom Row
Drill a hole 7-8” up from the bottom and
2-3” back from the front of the cabinet.
Drill the second hole 7-8” up from the bottom
and 24-26” (14-16” for 191/4” deep cabinets)
from the front of the cabinet.
Drill a third hole 7-8” up from the bottom and
evenly spaced horizontally between the first
two holes.
Middle Rows
Drill two rows (1 row for 68” tall cabinets)
evenly spaced between the top and bottom rows.
Use the same vertical spacing as the top and
bottom rows.
NOTE: Cabinet shelves are
not sho n for clarity.

6
COVER PANEL INSTALLATION CONTINUED
Non-marring
Padded Clamp
Note: Cabinet shelves are not sho n for clarity.
6. Raise the Cover Panel into position covering the cabinet side panel and flush with the
front edge as in Step 3.
7. Clamp securely in position using at least two non-marring padded clamps.
8. nsert all 12 of the supplied #8 1-3/8” Wood Screws (9 are used on 68” cabinets).
Do not over-torque or strip out the scre s.
Tighten securely and remove the clamps.
9. nsert 1/4-20 nsert Nuts into the open holes at the
inside front edge of the cabinet side panel.
1/4-20
Insert Nut
#8 1-3/8”
Wood crew

7
COVER PANEL INSTALLATION CONTINUED
1/4-20 x 2.359
Machine crew
Plug Drill
Hole
Plug Drill
Hole
Note: Cabinet shelves are
not sho n for clarity.
1/4-20 x 2.359
Machine crew
CENTER COVER PANEL IN TALLATION
Use the following steps ONLY when a smaller cabinet is adjacent to a larger cabinet
with a cover panel in place on the larger cabinet.
1. nstall the Cover Panel using the procedures in “End Cover Panel nstallation” on page 4.
2. Align both cabinets to the desired configuration.
f the cabinets are different depths, they may be aligned to be
flush with the front as shown or flush with the back.
NOTE: Do not drill into a shelf or cross member.
Measure before drilling so that the hole is
1-2” from the nearest horizontal surface to
allow clearance for tools. t may be necessary
to move a hole and drill completely through the
smaller cabinet side panel, cover panel and
larger cabinet side panel simultaneously.
3. Drill two connecting holes through the
Cover Panel and attached cabinet side panel
(drill three holes if the cabinets are both
over 68” tall) using the 3/8” drill bit through
the holes already in the smaller cabinet.
4. f there is not enough room in the compartment
for a drill, it may be necessary to mark the holes
using a pencil through the connecting holes in the
smaller cabinet side panel, move the smaller
cabinet, drill the holes through the Cover Panel
and larger cabinet side panel, re-position the
smaller cabinet and connect them all together.
4. Connect the cabinets together using
1/4-20 x 2.359 Machine Screws.
5. Plug the hole at the other end with the Plugs
that were included with the cabinet.
6. Use of Filler Strips between the smaller cabinet
and the Cover Panel is required
(filler strips are included with cabinet).

8
REPLACEMENT PARTS LIST
Note: The follo ing parts are contained in the
Cover Panel Carton. Contact Wenger for
replacement part information.
Item Qty Description
1 1 Cover Panel
2 2 Screw, Machine, 1/4-20 x 2.359”
3 12 Screw, Wood, #8 x 1-3/8”
4 2 Plastic Guide Tack
5 1 Screw, #8 x 1-1/4”
6 4 Nut, nsert, 1/4-20
7 1 End Cover Extrusion
1
3
4
2
5
7
6