Wenger 5-light 30" Studio Makeup Station User manual

Installation Instructions
Studio®Makeup Station
30-inch Model
36-inch Model
9-light 36-inch Studio
Makeup Station
CONTENTS
Fasteners and Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Fasteners Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Before Starting The Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Layout the Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Install the Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Install the First Makeup Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Install Additional Makeup Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Complete the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Attach the Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Attach the Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Connect the Electrical Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Tackboard Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ote: Please read and understand the Studio Makeup Station Installation Instructions before
assembling the parts.
ote: Refer to the illustrations on the following pages. If you need additional information about
your Studio Makeup Station, write, email, or telephone Wenger Corporation at the number or
addresses below.
ote: Two people must work together for some assembly steps.
ote: Because wall construction varies, wall anchors are not supplied with the Studio Makeup
Station.
6-light 36-inch Studio
Makeup Station
8-light 30-inch Studio
Makeup Station
5-light 30-inch Studio
Makeup Station
©Wenger Corporation 2014 Printed in USA 02/14 Part #187A200-05
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com

2
FASTENERS AND PART LIST
(1) Self-drill Screw,
1/4-14x3/4"
(2) Hex Flange Nut, 3/8-16
Item Qty. Description Item Qty. Description
1 2* Self-drill Screw, 1/4-14x3/4" 6 2* Bottom Frame Clips
2 4* Hex Flange Nut, 3/8-16 7 1 Wall Mounting Bracket
3 4* Phillips Head Sheet Metal Screw, 10x3/4" 8 1 Counter
4 1* Installation Manual (including Wiring Diagram) 9 1** Tackboard Assembly
5 1* Owner’s Manual 10
REQUIRED TOOLS
Tools required for assembly are a 3/8" or 1/2" cordless drill, a phillips screwdriver or a phillips insert bit,
a 3/8" hex nut driver, a 9/16" open end wrench, a 48" box level, an electronic scanner to locate wall
studs, an eight-foot tape rule, pencil, and bits and drivers for wall anchor hardware (supplied by end
user).
3/8" or 1/2" Cordless Drill
3/8" Hex Nut Driver Insert
Phillips Insert Bit 9/16" Open End Wrench
Phillips Screwdriver
48" Box Level
3/4"
Electronic Scanner
FASTE ERS
(3) Phillips Head Sheet
Metal Screw, 10x3/4"
PART LIST
3/4"
* Contained in Hardware Bag
The Makeup Station is shipped with all components in a single box, the main assembly, a corrugated
sleeve containing the Mirror, a hardware bag, the Counter under the main assembly, the Tackboard
Assembly (36-inch Model only) in a corrugated sleeve, and the Wall Mounting Bracket.
Lead Pencil
8' Tape Rule
** 36-inch Model Only

3
INSTALLATION
Before installing the Studio Makeup Station, do the following.
1. Read and understand this installation instruction completely.
2. Open all cartons and make sure each includes a Studio Makeup Station, a hardware bag, the Wall
Mounting Bracket, a Tackboard (36-inch Model only), a Mirror (packaged in a corrugated sleeve)
and a Counter.
ote: The Counter and carton containing the Mirror are packaged under the Makeup Station.
3. Inventory the hardware package and make sure that all required hardware is present.
Warning: ersonal injury or damage to property can happen if the instructions in this manual
are not followed.
Warning: The 36-inch Model Studio Makeup Station weighs about 80-pounds and the 30-inch
Model Studio Makeup Station weighs about 72-pounds when completely assembled.
Serious injury or damage to the Station can happen if only one person attempts to
move or lift the Station. Two people must always work together when lifting or
moving the Studio Makeup Station.
Warning: Never lift the completely assembled Makeup Station by grasping the wire cages or the
Shelf. Damage to the wire cages can occur. Always lift or move the Station by
grasping the steel frame or the mirror surround.
Warning: Do not connect the Makeup Station to an electrical source until the installation is
complete and the Mirror and Counter are in place. Failure to observe this precaution
can result in serious injury or death!
ote: Wall anchors are not supplied because wall constructions vary. Before starting the installation of
the Studio Makeup Station, obtain the required wall anchors.
Warning: Always wear safety glasses and safety shoes when installing the Studio Makeup
Station. Failure to observe this precaution can result in serious injury.
BEFORE STARTI G THE ASSEMBLY
!WARNING
Two people are
always required to
lift or move the
Studio Makeup
Station Assembly.
!WARNING
Read and
understand the
entire manual
before starting the
installation.
Shelf
Steel Frame
Mirror
Mirror Surround
Wire Cage
9-light Studio Makeup
Station Assembly
!CAUTION
ever lift the
Makeup Station
Assembly by the
grasping the wire
cages.
!WARNING
Do not connect the
Makeup Station to
the electrical source
until the Makeup
Station is
completely
assembled.
Do not use the Wire
Cages to lift the
Makeup Station.
Hardware Bag
Tackboard only with
the 36-inch Model

4
INSTALLATION CONTINUED
BEFORE STARTI G THE ASSEMBLY CO TI UED
4. The room where the Makeup Stations will be installed must be permanently wired with a suitable
electrical source (grounded 120VAC).
a. Each 9-light Station (lighting using 540 watts) or 8-light Station (lighting using 480 watts) can
have external appliances plugged into the duplex receptacle that can draw high current loads.
Make sure that the electrical supply is capable of supplying sufficient current and has adequate
overload protection.
b. Always consult local electrical codes before starting the installation.
Warning: A licensed electrician must do the electrical installation. Failure to observe this
precaution can result in serious injury, death, or damage to property.
Warning: The studio electrical source must must be permanently wired and comply with local
electrical codes. This must include a switch(s) that can disconnect the Studio Makeup
Station outlet(s) and must include a pilot light outside the dressing room door to
indicate that the outlet circuitry is energized. Failure to observe this precaution can
result in serious injury, death, or damage to property.
LAYOUT THE SPACE
ote: Refer to the illustration on the opposite page (page 5) which includes equivalent metric
dimensions.
1. Before starting the installation, decide where the Studio Makeup Stations will be installed.
2. If the wall is drywall or wetwall construction, determine if the studs are wood or steel.
3. Draw a vertical line on the wall that will locate the vertical centerline of the left (or right) Station.
a. Make sure that the line is vertical to the floor.
b. The centerline cannot be closer than 20-1/2-inches (36-inch Model) or 17-1/2-inches (30-inch
Model) from an obstruction on either side (such as a wall, I-beam, cabinet, etc.).
c. If more than one Studio Makeup Station is being installed, measure 30-inches or 36-inches
(depending upon the Model) from the centerline and draw another vertical line for the centerline
of the second Station.
d. Draw additional centerlines for any additional Stations that will be installed.
e. Draw a horizontal line 57-1/2-inches from the floor across the centerlines. Make sure that the
line is level. This line locates the top edge of the Mounting Bracket (36-inch Model is 23-1/2-
inches wide and 30-inch Model is 17-1/2-inches).
ote: Placing the top edge of the Mounting Bracket at 57-1/2-inches from the floor will locate the top
surface of the Counter at 29-inches from the floor and the top of the Shelf at 68-1/2-inches from
the floor. If the Counter top surface must be higher or lower, adjust the Mounting Bracket
Position by moving it upward or downward.
4. Using an electronic scanner, locate and mark each stud in the wall that will be used for the
installation with a vertical line that passes through the horizontal line that locates the top edge of the
Mounting Bracket.
ote: Sometimes the 30-inch Model Mounting Bracket does not cross a wall stud. If the Mounting
Bracket cannot be attached to a wall stud, refer to the special instructions for wall anchors in the
section Install the Mounting Bracket.
LIGHTI G
The Studio Makeup Station is shipped without light bulbs. Wenger Corporation recommends the use of
GE Reveal®40-watt or GE Reveal®60-watt incandescent bulbs or 15 watt full-spectrum swirl
fluorescent bulbs. Ambient lighting conditions may influence the choice of bulb type and power rating.

5
36"**
(91.44 cm)
20-1/2" Minimum Distance to a Wall (52.07 cm)*
57-1/2"
146.05 cm)
Floor
Corner
Top Surface of Counter
Top Surface of
Shelf
Top Edge of
Mounting Bracket
Centerline of
each Station
29"
(73.66 cm)
9-light Makeup Station
6-light Makeup Station
INSTALLATION CONTINUED
LAYOUT THE SPACE CO TI UED
Station
Mounting Area
Top of Shelf
68-1/2"
(173.99 cm)
* 17-1/2" for 30-inch Model (44.45 cm)
** 30" for 30-inch Model (76.20 cm)
36-inch Model Layout
36"**
(91.44 cm)
36"**
(91.44 cm)

6
INSTALLATION CONTINUED
I STALL THE MOU TI G BRACKET
1. Remove the Mounting Bracket from the shipping box.
2. Locate the Hardware Bag and set it aside.
3. Align the Mounting Bracket to the wall with the top edge of the Mounting Bracket on the Horizontal
LIne and the centerline of the Mounting Bracket (user must mark the Bracket centerline with chalk)
aligned to the Station Centerline on the wall as shown below.
4. For walls with wood stud construction do as follows. For metal stud or masonry wall construction,
go to step 5.
a. Hold the Mounting Bracket in place and note the position of the studs.
ote: The mounting bracket must crosss at least one stud.
b. If the Mounting Bracket crosses two studs, attach the Bracket with four 1/4x3" Hex Head Lag
Screws (supplied by end user), two in each stud.
c. If the Mounting Bracket crosses one stud, attach the Bracket with two 1/4x3" Hex Head Lag
Screws (supplied by end user) to the stud and then attach the Bracket to the wall with four
heavy duty drywall anchors (consult a local hardware supplier).
Station Centerline
Mounting Bracket
Position of Studs
Horizontal Line for Top Edge
of Mounting Bracket
Mounting Bracket Centerline
3
4b
Position of Studs
Bracket crosses two studs.
Hex Head Lag
Screw, 1/4x3"
!WARNING
Always wear safety
glasses and safety
shoes when
installing the Studio
Makeup Station to
avoid serious injury.
Mark the Bracket centerline
with caulk on the top
surface of the Bracket.
4c
Bracket crosses one stud.
Position of Stud
Hex Head Lag Screw, 1/4x3"
Mounting Bracket Centerline
Mounting Bracket
Centerline

7
INSTALLATION CONTINUED
I STALL THE MOU TI G BRACKET CO TI UED
5. For walls with metal stud construction do as follows.
a. Hold the Mounting Bracket in place and note the position of the studs.
ote: the mounting bracket must cross at least one stud.
b. If the Mounting Bracket crosses two studs, attach the Bracket with four #14x2" Self-drilling
Screws (supplied by end user), two in each stud.
c. If the Mounting Bracket crosses one stud, attach the Bracket with two #14x2" Self-drilling
Screws (supplied by end user) to the stud and then attach four heavy duty drywall anchors
(consult a local hardware supplier) to the wall.
6. For masonry walls, use at least two 1/4-inch masonry anchors that are appropriate for the wall
construction (consult a hardware supplier).
7. Repeat this procedure for all Station Mounting Brackets.
ote: Install all Mounting Brackets before hanging any Studio Stations.
5b
Position of Studs
Bracket crosses two studs.
Self-drilling Screw,, #14x2"
5c
Bracket crosses one stud.
Position of Studs
Self-drilling Screw,, #14x2"

8
INSTALLATION CONTINUED
I STALL THE FIRST MAKEUP STATIO
1. Remove the four Flange Nuts, 3/8-16, from the hardware bag.
2. Screw (clockwise) a Flange Nut, 3/8-16, onto each each of the two Mounting Bracket Studs with the
Flanges facing upward as shown below. Position the Flange Nuts so that the flange of the nut is
one-half inch from the top edge of the Mounting Bracket.
1/2"
Mounting Bracket
Flange Nut, 3/8-16
Mounting Bracket
Flange Nut, 3/8-16
Mounting
Bracket Stud
Mounting Bracket
Stud
ote: When installing two or more Makeup Stations, always first install a 6-light or 5-light unit on the
left end. Add additional 6-light or 5-light units to the right and finish the row with a 9-light or 8-
light unit on the right end.
3. Find the shipping container marked 6-light unit or 5-light unit.
a. With two people working together, place the shipping container onto a flat surface near the
installation wall.
b. Remove the cover and fold the sides down.
Flange facing upward and 1/2"
from the top of the Mounting
Bracket.
Cover
Shipping Container Sides
Counter Bottom Surface
6-light or 5-light Makeup Station
!WARNING
Two people are
always required to
lift or move the
Studio Makeup
Station Assembly.
The Counter and the Mirror Carton are
shipped under the Makeup Station.

9
INSTALLATION CONTINUED
I STALL THE FIRST MAKEUP STATIO CO TI UED
6. With two people working together, tilt the Makeup Station into an upright position.
a. Only handle the MakeupStation by grasping the Steel Frame — do not lift or handle the
Makeup Station by grasping the Light Cages or the Shelf.
ote: Always start a row with a 6-light unit or a 5-light unit on the left end. Add additional 6-light or 5-
light units to the right and finish the row with a 9-light unit or 8-light unit on the right end.
Always lift by grasping
the Makeup Station Frame
Never lift the Makeup Station
by grasping the Makeup
Station Wire Cages
Wire Cage
Makeup Station Frame
9-light or 8-light Makeup Station6-light or 5-light Makeup Station
Always install the 6-light
Makeup Station first and
on the left side.
!CAUTION
ever lift the
Makeup Station
Assembly by the
grasping the wire
cages.
!WARNING
Two people are
always required to
lift or move the
Studio Makeup
Station Assembly.
Never lift the Makeup Station
by grasping the Makeup
Station Shelf
!CAUTION
ever lift the
Makeup Station
Assembly by the
grasping the Shelf.

10
INSTALLATION CONTINUED
I STALL THE FIRST MAKEUP STATIO CO TI UED
7. Attach the 6-light or 5-light Makeup Station to the left-hand Mounting Bracket as follows.
a. With two people working together, grasp the Makeup Station Frame and lift the Station upward.
Warning: Be careful to not pinch fingers between the wall or Wall Mounting Bracket when
placing the Makeup Station onto the Mounting Bracket Studs.
b. Place the Frame onto the Mounting Bracket Studs by engaging the Studs with the Frame Upper
Bracket Slots. Allow the Makeup Station to rest on the two Flange Nuts on the Mounting Bracket
Studs.1
c. Screw a Flange Nut with the Flange facing downward onto the top of each Mounting Bracket
Stud by hand. Leave the Flange Nut loose for later adjustment.
ote: If the Mounting Bracket Studs do not align to the Frame Upper Bracket Slots, loosen the screws
that attach the Mounting Bracket to the wall. Then, after placing the Frame onto the Mounting
Bracket Studs, tighten the screws that attach the Mounting Bracket to the wall.
6-light or 5-light Makeup Station
Flange Nut, 3/8-16
Front View
Rear View (from Wall)
7a-b
7c
Flange Nut, 3/8-16
Mounting Bracket
Frame Upper
Bracket Slot
Frame Upper
Bracket
Mounting Bracket Stud
Mounting Bracket
Rear View (from Wall)
!WARNING
Avoid pinching
fingers between the
Station and the wall
or bracket when
engaging the
mounting bracket
studs.

11
INSTALLATION CONTINUED
I STALL THE FIRST MAKEUP STATIO CO TI UED
8. Level the Makeup Station as follows.
a. Place a 48" Box Level across the two Counter Mounting Brackets.
b. To move the left side upward, use a 9/16-inch open end wrench and turn the Left Lower Flange
Nut counterclockwise and the Right Lower Flange Nut clockwise. Turning each nut one-half turn
will lift the left edge 1/16-inch.
ote: Always turn one nut clockwise and one nut counterclockwise the same amount to keep the
Makeup Station in the same relative position. This is important when leveling a group of Makeup
Stations.
c. To lower the left side, turn the Left Lower Flange Nut clockwise and the Right Lower Flange Nut
counterclockwise.
d. When the Counter Mounting Brackets are level, tighten the two Upper Flange Nuts with a 9/16-
inch open end wrench.
Box Level
Counter Mounting Brackets
Mounting Bracket
Mounting Bracket
Left Lower Flange Nut
Right Lower Flange Nut
Upper Flange Nut

12
INSTALLATION CONTINUED
I STALL ADDITIO AL MAKEUP STATIO S
ote: Always start a row with a 6-light or 5-light unit on the left end. Add additional 6-light units to the
right and finish the row with a 9-light unit or a 8-light unit on the right end.
1. Find a shipping container with the next required unit.
a. With two people working together, place the shipping container onto a flat surface near the
installation wall.
b. Remove the cover and fold the sides down.
2. Place the Makeup Station onto the Mounting Bracket next to the 9-light or 8-light Makeup Station.
3. Level the Makeup Station making sure that the Counter Mounting Brackets are even and tighten the
Upper Flange Nuts.
4. Install any additional Makeup Stations in the same way.
COMPLETE THE I STALLATIO
1. Fasten the bottom of the Makeup Station Frame to the wall with Bottom Frame Clips as follows.
a. Hold a Bottom Frame Clip against the Frame and mark the lower hole location for the Wall
Anchor with a pencil as shown below.
b. Install a medium duty wall anchor (supplied by the end user — consult a local hardware
supplier) at the mark on the wall.
c. Attach a Bottom Frame Clip to the Frame with a #14 Self-drilling Screw (from the hardware bag)
and fasten the Clip to the wall with the wall anchor screw.
2. Continue installing the Bottom Frame Clips to all of the Makeup Stations.
Makeup Station Frame
Bottom Frame Clip
Pencil
1a
Make the wall anchor
location here
Install a medium duty wall
anchor on the mark
1b
1c
Bottom Frame Clip #14 Self-drilling Screw
Attach the Bottom Frame Clip with a #14 Self-
drilling Screw and a wall anchor screw.

13
1. Remove the Mirror from the shipping carton and inspect the Mirror for damage.
2. With two people working together, place the Mirror against the Frame about an inch from the top
with Mirror Flange at the bottom.
3. Slide the Mirror upward until the Mirror Flange contacts the Frame and the top clips engage the
Frame..
4. With one person holding the Mirror in place, attach the two Pan Head Screws (included with the
Mirror in the sleeve) that hold the Mirror to the Frame.
Caution: Tighten the an Head Screws only enough to be
snug. Over tightening will strip the threads in the
Frame.
Mirror
Pan Head Screw
Slide the Mirror upward until the top
clips engage the flange on the Frame.
Pan Head Screw
Shelf Bottom Surface
INSTALLATION CONTINUED
ATTACH THE MIRROR
ATTACH THE COU TER
1. Assemble the Counter to the Makeup Station.
a. Remove the Counter from the carton and locate the four Pan Head Screws in the Hardware
Bag.
ote: If there is a strap or tape attaching the flexible conduit to the Counter Support Bracket, remove
the strap or tape before placing the Counter onto the Counter Support Brackets.
b. Place the Counter onto the Counter Support Brackets and slide it into place.
c. It may be necessary to lift the curved edge of the
Counter slightly upward to fit it into the space in the
Frame.
d. Attach the Counter to the Counter Support Brackets with
the four Pan Head Screws
Caution: Tighten the an Head Screws only enough to be
snug. Over tightening the screws will strip the
threads in the Counter.
Pan Head Screw
Counter Bottom Surface
Counter Support Brackets

14
INSTALLATION CONTINUED
CO ECT THE ELECTRICAL SOURCE
Warning: To reduce the risk of burns, fire, electric shock or injury to persons, observe the
following warnings.
• Never connect the electrical source until all of the Makeup Stations are
completely assembled with Mirrors and Counters in place.
• Never connect the Makeup Stations to an inadequate electrical circuit.
• Always have an electrical engineer design or review the circuits to make sure that
they comply with electrical codes and anticipated use.
• Always have a licensed electrician make any electrical connections.
• Never modify the wiring inside the Makeup Stations.
• Never allow anyone to use the Makeup Stations until all electrical work is
complete and light bulbs are installed.
otes to the Electrician:
1. The Studio Makeup Station has separate conductors for the lights and the receptacle (see illustration
below). The wiring plan for the room may include separate circuits for lights and receptacles.
2. From N.E.C. Article 520.73 (2002): All lights and any receptacles adjacent to the mirror(s) and
above the dressing table counter(s) installed in dressing rooms shall be controlled by wall switches
installed in the dressing room(s). Each switch controlling receptacles adjacent to the mirror(s) and
above the dressing table counter(s) shall be provided with a pilot light located outside the dressing
room, adjacent to the door to indicate when the receptacles are energized. Other outlets installed in
the dressing room shall not be required to be switched.
3. If the wiring plan for the room does not comply with the above code requirement, check with the
electrical engineer or local code official before proceeding.
4. Never sit or stand on the counter or use it for holding tools while connecting the Makeup Station to
the electrical source.
White, Neutral
Black, 120 VAC
Green, Ground
Conduit
TACKBOARD I STALLATIO
Refer to the Studio Makeup Station Owner’s Manual for Tackboard installation instructions.

15
The Studio Makeup Station is guaranteed free of defects in materials and workmanship for five full
years.
Our guarantee assures you of either a full refund or repair or replacement of the defective
materials or workmanship without charge, at the discretion of our Customer Service Department. ust
call a Customer Service Representative at 1-800-887-7145 and state the reason you are dissatisfied. If
a product return is necessary, your representative will issue a return authorization. This is your sole
remedy for breach of this warranty.
Should you have a question or problem with any Wenger product, don’t hesitate to call, even if the
product is past warranty. It’s important to us that all our customers be satisfied.
This is the sole warranty made by Wenger. Wenger disclaims all other warranties, including
the warranties of merchantability and fitness for a particular purpose, as well as all liability for incidental,
consequential, special, and indirect damage. Wenger liability for direct damages shall be limited to the
amount you paid for the product involved. Wenger reserves the right to make product changes without
obligation to incorporate such changes into products previously sold.
Some states do not allow the exclusion or limitation of damages or warranties, so the above may not
apply to you. This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.
WARRANTY

16
This page is intentionally blank.