Wenger Tablet Arm User manual

Assembly Instructions
 !*$1/+
%-/$,&$/* 6/(&'1' (/0
-1$ Please read and understand these Tablet Arm Assembly Instructions before attempting
installation, assembly, or use.
-1$ Remove all items from the shipping containers and sort the components by type, size, etc.
Refer to the illustrations on the following pages. If you need additional information,
contact the Wenger Corporation using the information below.
©Wenger Corporation 2011 Printed in USA 03/11 Part #109 135-01
$,&$/-/.-/ 1(-, 555 Park Drive, P.O. Box 448, Owatonna, innesota 55060-0448
Questions? Call.....USA: 1-800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com
CONTeNTs
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Fastener Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
anufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Routine aintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2
beFOre yOU begIN
Read and understand the complete assembly procedure before you begin.
Remove all items from the shipping carton.
The Wenger Tablet Arm is guaranteed free of defects in materials and workmanship for five full years.
Our guarantee assures you of either a full refund or repair or replacement of the defective materials or
workmanship without charge, at the discretion of our Customer Service Department. Just call a
Customer Service Representative at 1-800-887-7145 and state the reason you are dissatisfied. If a
product return is necessary, your representative will issue a return authorization. This is your sole
remedy for breach of this warranty.
Should you have a question or problem with any Wenger product, don’t hesitate to call, even if the
product is past warranty. It’s important to us that all our customers be satisfied.
This is the sole warranty made by Wenger. Wenger disclaims all other warranties, including the
warranties of merchantability and fitness for a particular purpose, as well as all liability for incidental,
consequential, special, and indirect damage. Wenger liability for direct damages shall be limited to the
amount you paid for the product involved. Wenger reserves the right to make product changes without
obligation to incorporate such changes into products previously sold.
Some states do not allow the exclusion or limitation of damages or warranties, so the above may not
apply to you. This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.
WArrANTy
reqUIred TOOls
FAsTeNer PArTs lIsT
Screw, Speaker, ZP,
#10-24 x 0.870
The following tools are required to assemble and attach the Tablet Arm.
•7/16” Box Wrench
•3/8” Box Wrench
•1/2” Socket
•7/16” Socket
•2” Socket Extension
•Ratcheting Wrench
•Phillips Head Screwdriver
Nut, Lock, Flange,
#10-24
Screw, S , PH, ZP
8 x 1/2
Screw, Tapping, LG,
5/16 x 3/4
Capscrew, GD 2, ZP,
1-1/4-20 x 1-1/2
Nut, NY. IN, Full, ZP,
1/4-20 Note: Hardware Pack may contain extra fasteners.

3
ImPOrTANT User INFOrmATION

Copyright © 2011 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in
any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser's personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that might
occur. The end user must exercise caution and common sense when assembling or installing Wenger
Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-887-7145.

The Tablet Arm is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, N 55060
1-800-4WENGER (493-6437) • 1-507-455-4100
www.wengercorp.com
 
•This product is designed to provide a desktop work surface while the chair is in use.
•This product is intended for indoor use in normal ambient temperature and humidity conditions.
•This product is intended to be used only as described in these instructions.
rOUTINe mAINTeNANCe
1. Replace damaged parts promptly.
2. Lubrication of Tablet Arm components is not necessary under normal circumstances.
In dusty or abnormal environments, moving parts may be lubricated using any
white lithium grease or petrolium based lubricant.
Note: Dry film lubricants are less likely to trap dust or other contaminants.

4
rePlACemeNT PArTs lIsT
1$+ 16 $0"/(.1(-, 1$+ 16 $0"/(.1(-,
1 2 Screw, Speaker, ZP, #10-24 x 0.870 7 2 Spacer, Tablet Arm Bracket
2 2 Nut, Lock, Flange, #10-24 8 2 Pivot Bracket, Tablet Arm
3 6 Screw, S , PH, ZP, 8 x 1/2 9 1 Cover, Pivot Bracket, Tablet Arm
4 4 Screw, Tapping, LG, 5/16 x 3/4 10 1 Support Tube, Tablet Arm
5 1 Capscrew, GD 2, ZP, 1-1/4-20 x 1-1/2 11 1 Bracket, Desk, Tablet Arm
6 1 Nut, NY. IN, Full, ZP, 1/4-20 12 1 Desk, Tablet Arm
3
4
5
10
6
1
2
12
11
3
4
7
7
8
8
9

5
Assembly
1. ount the Tablet Arm Desk to the Support Tube as follows:
a. Slide the Desk Bracket over the end of the Support Tube
so that the slots engage the Stop Pins.
Be sure that the slots in the Desk Bracket are orientated
to the inside of the chair (away from the longest side of
the Tablet Arm Desk).
From the user’s viewpoint, this allows the Tablet Arm
Desk to rotate clockwise.
NOTE: The first and third angled slots are for
right hand set-up.
b. For proper Tablet Arm Desk placement,
thread two #10-24 x 0.870 Speaker Screws
into the pre-drilled holes in the Tablet Arm Desk
and through the Desk Bracket.
Secure them both with a #10-24 Lock Nut.
NOTE: The Speaker Screws may have to be
started by tapping them into the pre-drilled
holes with a hammer.
c. Thread the six 8 x 1/2” Pan Head Screws
through the Desk Bracket and into the
Tablet Arm Desk. Tighten the screws until
they are fully seated.
 !*$1/+
$0)
$0)
/ ")$1
57 ,
$ #"/$40
2..-/1
2!$

-")21
5
.$ )$/"/$40
1-.(,0