Wenger Violin User manual

Important User Information � � � � � � � � � � � � � � � � � � � � � � � � � � �2
General ��������������������������������������2
Manufacturer ����������������������������������2
Intended Use����������������������������������2
Warranty �������������������������������������2
Safety Precautions � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �3
Required Tools� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �3
Hardware Parts List� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �4
Violin/Viola Storage Rack Components � � � � � � � � � � � � � � � � �4
Preassembly � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �5
Assembly� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �8
Operation� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �11
Replacement Parts List � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �12
Assembly Instructions
Violin/Viola Storage Rack
©Wenger Corporation 2023 Printed in USA 2023-09 Part #148J056-02
Wenger Corporation, 555 Park Drive, PO Box 448, Owatonna, Minnesota 55060-0448
Questions? Call�����USA: (800) 4WENGER (493-6437) • Worldwide: [phone] • wengercorp�com
Contents
Note: Please read and understand these instructions before assembly or use�
Note: If you need additional information, contact Wenger Corporation using the information below�
Visit the Violin/Viola Storage Rack web page at wengercorp.com for more information.

2
Important User Information
General
Copyright © 2023 by Wenger Corporation
All rights reserved� No part of the contents of this manual may be reproduced, copied, or transmitted in any form
or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information
storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser's
personal use�
Printed and bound in the United States of America�
The information in this manual is subject to change without notice and does not represent a commitment on the
part of Wenger Corporation� Wenger Corporation does not assume any responsibility for any errors that may
appear in these instructions�
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct,
indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions�
The manufacturer reserves the right to change this product at any time�
The information in this document is not intended to cover all possible conditions and situations that might occur�
The end user must exercise caution and common sense when assembling or installing Wenger Corporation
products� If any questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437)
or [phone] worldwide�
Manufacturer
The Violin/Viola Storage Rack manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • [phone]
wengercorp�com
Intended Use
• This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions�
• This product is intended to be assembled and used only as described in these instructions�
Warranty
This product is guaranteed free of defects in materials and workmanship for ve full years from date
of shipment� A full warranty statement is available upon request�

3
Required Tools
• Rubber or plastic mallet
• Phillips head screwdriver or insert bit
• Variable speed drill (to drive hex socket screws)
• 5/32" (4 mm) Hex insert bit (supplied)
• #2 Square drive bit (supplied)
Throughout this document you may nd cautions and warnings which are dened as follows:
• WARNING: Failure to follow the instruction could result in serious injury or damage to property�
• CAUTION: Failure to follow the instruction could result in minor injury or damage to property�
Read all of these safety instructions before using the equipment�
Make sure anyone assembling
the Violin/Viola Storage Rack
has read and understands these
instructions.
To avoid damage or injury, more
than one person is required for
assembly.
Failure to comply with Warnings
and Cautions in this document
can result in damage to property
or serious injury.
Safety Precautions
!CAUTION !CAUTION !CAUTION

4
*Extra hardware can be discarded.
Violin/Viola Storage Rack Components
Item Description
7Base Panel
8Divider Panel
9Caster Bracket
10 Base Support
Spacer Dowel
11 Neck Support
Panel
12 Neck Support
Divider Peg
13 Neck Support
Cross Panel
14 End Panel
15 Locking Caster
16 Non-locking
Caster
Hardware Parts List
7 x 50 mm
Hex Socket Lag Screw
1
Wood Dowel
2
#8-32
Insert Nut
3
3/16" ID x 1/2" OD
Flat Washer
4
8-32 x 3/4"
Machine Screw
5
#8-10 x 1-1/2"
Square Drive
Screw
6
7
9
11
13
15
810
12
14
16

5
1� Assemble the lower base support�
a� Attach a divider panel (#8) to a base panel (#7)
using one wood dowel (#2) and
one 7 x 50 mm hex socket lag screw (#1)�
The dowel will only t into the larger holes
of the divider panel.
b� Select another base panel (#7) and pound two
#8-32 insert nuts (#3) into the front of each corner�
Dowel hole is not visible from the front face of
the base panel.
c� At the rear of the base panel, attach a
caster bracket (#9) to both sets of insert nuts
using 3/16" ID x 1/2" OD washers (#4) and
8-32 x 3/4" machine screws (#5)�
d� Insert a wood dowel (#2) into the upper hole
of the attached divider panel�
e� Insert six base support spacer dowels (#10)
into the dugout holes of the rst base panel.
f� Align the dugout holes of the second
base panel with both the divider panel dowel
and base support spacer dowels�
Attach it to the divider panel using one
7 x 50 mm hex socket lag screw (#1)�
Preassembly
Divider
Panel
(8)
Dowel will only t
in larger hole
Base
Panel
(7)
Wood
Dowel
(2)
7 x 50 mm
Hex Socket
Lag Screw
(1)
Base
Panel
(7)
Dowel hole
not visible
#8-32
Insert Nuts
(3)
Caster Bracket
(9)
8-32 x 3/4"
Machine
Screws
(5)
3/16" x 1/2"
Washers
(7)
Base Support
Spacer Dowels
(10) Wood
Dowel
(2)
7 x 50 mm
Hex Socket Lag Screw
(1)

6
2� Assemble the upper base support�
a� Attach a divider panel (#8) to a base panel (#7)
using one wood dowel (#2) and
one 7 x 50 mm hex socket lag screw (#1)�
The dowel will only t into the larger holes
of the divider panel.
b� Select another base panel (#7) and pound
two #8-32 insert nuts (#3) into the front of each corner�
Dowel hole is not visible from the front face
of the base panel.
c� Insert a wood dowel (#2) into the upper hole
of the attached divider panel�
d� Insert six base support spacer dowels (#10)
into the dugout holes of the rst base panel.
e� Align the dugout holes of the second
base panel with both the divider panel dowel
and base support spacer dowels�
Attach it to the divider panel using one
7 x 50 mm hex socket lag screw (#1)�
Preassembly (continued)
Divider
Panel
(8)
Dowel will only t
in larger hole
Base
Panel
(7)
Wood
Dowel
(2)
7 x 50 mm
Hex Socket
Lag Screw
(1)
Base
Panel
(7)
Dowel hole
not visible
#8-32
Insert Nuts
(3)
Base Support
Spacer Dowels
(10)
Wood
Dowel
(2)
7 x 50 mm
Hex Socket Lag Screw
(1)

7
3� Assemble both the lower and upper neck supports�
The assembly is the same for both and can be done at the same time�
a. With the at end facing in (rounded end facing out),
insert seven neck support divider pegs (#12)
into both neck support top panels (#11)�
Secure each peg using one #8-10 x 1-1/2"
square drive screw (#6)�
b Attach a neck support cross panel (#13)
to each neck support top panel using four
wood dowels (#2) and four 7 x 50 mm
hex socket lag screws (#1)�
The dowels will only t into the larger
holes of the neck support top panel
and the dowel holes are not visible
from the front face of the neck
support cross panel.
Preassembly (continued)
#8-10 x 1-1/2"
Square Drive
Screw
(6)
Flat end facing in,
round end facing out
Neck Support
Top Panel
(11)
Neck Support
Cross Panel
(13)
Dowel will only t
in larger hole
Wood
Dowel
(2)
7 x 50 mm
Hex Socket
Lag Screw
(1)
Neck Support
Divider Peg
(12)

8
1� Pound two #8-32 insert nuts (#3) into a rear corner of both
end panels (#14) to make both a left-hand and a right-hand
side as shown�
These will become the outside panel surfaces.
2� At the opposite side (inside panel surface) of each end panel,
attach a caster bracket (#9) to the insert nuts using
3/16" ID x 1/2" OD washers (#4) and
8-32 x 3/4" machine screws (#5)�
Assembly
#8-32
Insert Nuts
(3)
End Panel
(14)
Caster Bracket
(9)
8-32 x 3/4"
Machine
Screws
(5)
3/16" x 1/2"
Washers
(7)

9
3� Attach the lower base support assembly to both
end panels (#14) using four 7 x 50 mm hex socket
lag screws (#1) per side�
4� Attach the lower neck support assembly to both
end panels (#14) using three 7 x 50 mm hex socket
lag screws (#1) per side�
5� Attach the upper base support assembly to both
end panels (#14) using four 7 x 50 mm hex socket
lag screws (#1) per side�
6� Attach the upper neck support assembly to both
end panels (#14) using three 7 x 50 mm hex socket
lag screws (#1) per side�
Assembly (continued)
Lower Base
Support
Assembly
7 x 50 mm
Hex Socket Lag Screws
(1)
Lower Neck
Support
Assembly
Lower Base
Support
Assembly
7 x 50 mm
Hex Socket Lag Screws
(1)
Lower Neck
Support
Assembly

10
7� Carefully tip the unit onto its back and push the casters into the caster brackets�
The two locking casters (#15) attach to the front and the two non-locking casters (#16) attach to the back�
8� Tip the unit onto the casters and the assembly is complete�
Assembly (continued)
Locking
Caster
(15)
Non-locking
Caster
(15)

11
Before placing instruments on the mobile rack, be sure the casters are in the locked position�
Unlock the casters to move the rack�
Two people are recommended to move the rack�
Move the rack slowly and carefully making sure the instruments stay in place during transport�
Operation

12
Replacement Part List
Item Qty Description Item Qty Description Item Qty Description
1 40 Hex Socket Lag Screw , 7 x 50 mm 7 4 Base Panel 13 2 Neck Support Cross Panel
2 12 Wood Dowel 8 2 Divider Panel 14 2 End Panel
3 8 Insert Nut, #8-32 9 4 Caster Bracket 15 2 Locking Caster
4 9 Flat Washer, 3/16" ID x 1/2" OD 10 12 Base Support Spacer Dowel 16 2 Non-locking Caster
5 8 Machine Screw, 8-32 x 3/4" 11 2Neck Support Panel *Extra hardware can be discarded�
6 14 Square Drive Screw, #8-10 x 1-1/2" 12 14 Neck Support Divider Peg
14
7
11
13
15
16
6
1
12
2
9
3
4
5
8
10