Wenger Flex Quick start guide

Assembly Instructions and Owner’s Manual
Flex®Conductor’s Stand
ote: Please read and understand these instructions before assembling the parts.
ote: Remove all items from the shipping cartons and arrange them in a convenient location.
Refer to the illustrations on the following pages. If you need additional information,
contact the Wenger Corporation using the information below.
CONTENTS
©Wenger Corporation 2014 Printed in USA 12/14 Part #236C146-01
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Parts ist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Attach Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Attach Desk ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
To Set the Desk Height . . . . . . . . . . . . . . . . . . . . . . . . .7
To Tilt the Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
To Rotate the Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
To Move the Flex Conductor’s Stand . . . . . . . . . . . . . . .8
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Flex Conductors Stand
with Polycarbonate Desk
Flex Conductors Stand
with High-Pressure Laminate Desk

2
SAFETY PRECAUTIONS
Make sure t at anyone working wit
t e Flex Conductor’s Stand as read
and understands t ese instructions.
!CAUTION
Failure to comply wit t e
Warnings and Cautions in t is
document can result in damage
to property or serious injury.
!CAUTION
Throughout this manual you may find cautions and warnings which are defined as follows.
• WAR I G means that failure to follow the instruction may result in serious injury or death.
• CAUTIO means that failure to follow the instruction may result in serious injury or damage to
property.
Read all of the safety instructions before assembling or using the Flex Conductor’s Stand.
IMPORTANT USER INFORMATION
GE ERAL
Copyright © 2014 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in
any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser's personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that might
occur. The end user must exercise caution and common sense when assembling or installing Wenger
Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-733-0393.
MA UFACTURER
The Flex Conductor’s Stand is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
1-800-4WENGER (493-6437) • 1-507-455-4100
www.wengercorp.com
ITE DED USE
•This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
•This product is intended to be assembled and used only as described in these instructions.
WARRA TY
This product is guaranteed free of defects in materials and workmanship for five full years from date
of shipment. A full warranty statement is available upon request.

3
REQUIRED TOOLS
PARTS LIST
7
Item Qty Description
11Hex Head Capscrew, 5/16-18 x 2”
21Washer, 3/8 ID x 1-1/4 OD
31Base
41Oval Mast
51
Desk Surface
(Polycarbonate or High Pressure aminate)
61Carriage Bolt, 5/16-18 x 5”
72Nylon Washer, .375 ID x 1.43 OD
81ock Nut, 5/16-18
91Desk ip (High Pressure aminate only)
10 4 Binding Post Screw, #8-32 x 3/8
(High Pressure aminate only)
11 4 Binding Post Barrel, #8-32
(High Pressure aminate only)
1
2
3
4
6
8
• 1/2" Socket or Open/Box End Wrench
7
5
9
10
11
5
• Flat Head Screwdriver
(for High-Pressure Laminate Desk Lip only)

4
BASE ASSEMBLY
Attach the Oval Mast to the Base:
1. Insert the Oval Mast (#4) into the oval shaped hole at the top of the Base (#3).
Push the Oval Mast until it is flush with the bottom of the Base.
2. Secure the Mast to the Base with one 5/16-18 x 2-inch Hex Head Capscrew (#1)
and 3/8 ID x 1-1/4 OD Washer (#2).
3. Using a 1/2" Socket or Open End Wrench, tighten the Capscrew.
To prevent possible t read damage, only tig ten to a maximum torque of 240 in-lb.
ASSEMBLY
Do not force t e Oval Mast into t e Base.
Damage to t e components could occur.
!CAUTION
Oval Mast
(#4)
Base
(#3)
5/16-18 x 2” Hex
Head Capscrew
(#1)
3/8 ID x 1-1/4 OD
Washer
(#2)

5
ATTACH DESK
Attach the Desk to the Base Assembly:
1. Position the Desk Surface (#5) over the Neck Mounting Tube at the top of the Base Assembly.
ote: The lever for the Dual ock Position Feature should be on the same side
as the Release Trigger.
2. Slide the 5/16-18 x 5” Carriage Bolt (#6) through the square side hole in the Desk Bracket,
.375 ID x 1.43 OD Nylon Washer (#7) and through the Neck Mounting Tube.
Another .375 ID x 1.43 OD Nylon Washer (#7) fits between the Neck Mounting Tube and
Desk Bracket before pushing the Carraige Bolt through the other side of the Desk Bracket.
3. Secure the Desk to the Base Assembly using a 5/16-18 ock Nut (#8) on the
5/16-18 x 5” Carriage Bolt as shown.
ASSEMBLY (continued)
Dual
Locking
Feature
Lock ut,
5/16-18
(#8)
.375 ID x 1.43 OD
ylon Washer
(#7) Square Hole
in Desk Bracket
Base
Assembly
Trigger
Lock
5/16-18 x 5”
Carriage Bolt
(#6)
eck
Mounting
Tube
Desk Surface
(#5)
.375 ID x 1.43 OD
ylon Washer
(#7)
Lock ut,
5/16-18
(#8)
5/16-18 x 5”
Carriage Bolt
(#6)
.375 ID x 1.43 OD
ylon Washer
(#7)
Polycarbonate Desk is shown.
Procedure for High-Pressure Laminate Desk is the same.

6
ATTACH DESK LIP (HIGH-PRESSURE LAMI ATE DESK OLY)
If attac ing t e Basket Accessory, consult t e Assembly Instructions 236C128 before proceding.
Attach the Desk ip to the Desk Surface:
1. Fit the Desk ip (#9) to fit on the underside of the Desk Surface.
Align the holes as shown.
2. Attach the Desk ip to the Desk Surface with four #8-32 x 3/8 Binding Post Screws (#10)
and #8-32 Binding Post Barrels (#11).
ASSEMBLY (continued)
#8-32 x 3/8
Binding Post Screw
(#10)
#8-32
Binding Post Barrel
(#11)
Desk Lip
(#9)

7
TOSET THE DESK HEIGHT:
1. Disengage the Release Trigger mechanism by grasping the support neck
under the desk and pulling the trigger while supporting the desk.
2. Raise or lower the desk to the desired position and release the trigger.
3. The desk will lock in the nearest locking position.
Desk height can be set in 2" increments.
TOTILT THE DESK:
Tilt the desk to the desired angle.
The desk is held in place by friction and should hold approximately 35 lbs
at any angle without rotating as a result of the load placed on the desk.
OPERATION
To prevent t e desk from falling w ile
adjusting t e eig t, old on to t e desk
w en t e Release Lever is disengaged.
!CAUTION

8
1. Clean the Flex Conductor’s Stand with a mild detergent.
Avoid using harsh or abrasive cleaning products.
2. Never apply oil or any lubricant to the height adjustment tube.
3. Periodically check fasteners to ensure that they have not loosened during use.
MAINTENANCE
TOROTATE THE DESK:
1. The desk has lock positions at the 0 and 180 degree
positions.
2. Press upward on the ocking ever under the center
of the desk and simultaneously rotate the desk.
The desk automatically locks when rotated to the
180 or 0 degree position.
TOMOVE THE FLEX CO DUCTOR STA D:
1. Tilt the stand towards the wheels at the front of the boomerang shaped
cast iron base.
2. Push or pull stand assembly by grasping the upright mast just under
the desk.
OPERATION