Wenger 146M Series User manual

Assembly Instructions
Tall Folio Cabi ets
Note: Please read and understand these instructions before assembling the parts.
Note: Remove all items from the shipping cartons and arrange them in a convenient location.
Refer to the illustrations on the following pages.
If you need additional information, contact Wenger Corporation using the information below.
CONTENTS
©Wenger Corporation 2014 Printed in USA 08/14 Part #146M329-03
We ger Corporatio , 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 1-800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Leveling the Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Securing the Cabinet(s) to the Wall . . . . . . . . . . . . . . . . . . . .6
Numbering System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Changing Shelf Locations . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2
IMPORTANT USER INFORMATION
GENERAL
Copyright © 2014 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in
any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser's personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that might
occur. The end user must exercise caution and common sense when assembling or installing Wenger
Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-887-7145.
MANUFACTURER
The Tall Folio Cabinets are manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
1-800-4WENGER (493-6437) • 1-507-455-4100
www.wengercorp.com
INTENDED USE
•This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
•This product is intended to be assembled and used only as described in these instructions.
WARRANTY
These products are guaranteed free of defects in materials and workmanship for five full years from
date of shipment. A full warranty statement is available upon request.

3
BEFORE YOU BEGIN
•The Tall Folio Cabinet is shipped almost entirely assembled.
To install, level the unit and attach the few remaining components as outlined in these instructions.
•Read the complete assembly procedure before you begin.
•Remove all items from the shipping carton, and lay them out approximately in their final position.
REQUIRED TOOLS
The following tools must be available to assemble the Tall Folio Cabinets:
• Carpenter’s Level
• Carpenter’s Square
• Plastic Mallet
• Variable Speed Drill (to drive hex socket screws)
• 4mm ex Drive for Drill.

NOTE: Do Not try to level the cabinet to match soffits.
Do Not try to plumb the cabinet to match adjacent walls.
Do Not install door handles until cabinets have been leveled.For proper door alignment,
follow these instructions carefully.
See “Changing Shelf Locations” for removal of file drawers prior to leveling cabinet.
1. Check the level of the entire floor where the cabinets will be installed.
Determine the highest point of the floor in that area.
Extend all levelers until the bottom of the cabinet will be higher than
the highest point in the floor.
2. Adjust the levelers on one side until the front edges of the cabinet side
panels are plumb (side-to-side).
4
LEVELING THE CABINET

5
3. Measure A and B with a tape and adjust the front levelers until
A=B (+ 1/32 inch).
4. Adjust both front levelers equally until the front edges of the cabinet are
plumb (front-to-back).
5. Recheck that A=B and that the door is even with the top panel.
Readjust if necessary (steps 2 - 4).
Insert hole plugs into the two holes that are in the bottom shelf
for leveling the cabinet.
LEVELING THE CABINET (CONTINUED)