Weslo Gym 750 User manual

USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Model No. WLEVSY1825.0
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, please call:
Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: [email protected]
www.iconeurope.com
Visit our website at
08457 089 009

WARNING DECAL PLACEMENT
2
WESLO is a registered trademark of ICON IP
,Inc.
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the centre of
this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before
beginning assembly.
TABLE OF CONTENTS
The decal shown here has been placed on
the weight system. If the decal is missing or
illegible, please call the toll-free telephone
number on the front cover of this manual and
order a free replacement decal. Apply the
decal in the location shown.
VERTICAL WARNING
PN 218558 – Black Text/Clear Background
PN 218559 – White Text/Clear Background

3
1. Read all instructions in this manual and in
the accompanying literature and all warn-
ings on the weight system before using the
weight system. Use the weight system only
as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight system are ade-
quately informed of all precautions.
3. The weight system is intended for home use
only. Do not use the weight system in a com-
mercial, rental, or institutional setting.
4. Keep the weight system indoors, away from
moisture and dust. Place the weight system
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the weight
system to mount, dismount, and use the
weight system.
5. This weight system has an open weight
stack; the weight stack must not be accessi-
ble from any point outside of the user’s field
of view. To prevent access to the weight
stack, place the weight system in a corner or
bay of a room, as shown in the drawing
below. There must be no more than 1 meter
(3 ft. 4 in.) of clearance between the weight
system and the adjacent walls.
6. Inspect and properly tighten all parts regular-
ly. Replace any worn parts immediately.
7. Keep children under the age of 12 and pets
away from the weight system at all times.
8. Always wear athletic shoes for foot protec-
tion when using the weight system.
9. Keep hands and feet away from moving parts.
10. The weight system is designed to support a
maximum user weight of 135 kg (300 lbs).
11. Always stand on the foot plate when per-
forming an exercise that could cause the
weight system to tip.
12. Never release the arms, leg lever, or lat bar
whilst weights are raised; the weights will fall
with great force.
13. Always disconnect the lat bar from the
weight system when performing an exercise
that does not use the lat bar.
14. The weight system is designed to be used
only with the included weight. Do not use the
weight system with dumbbells or any other
type of weight to increase the resistance.
15. Make sure that the cables remain on the pul-
leys at all times. If the cables bind whilst you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.
16. If you feel pain or dizziness at any time
whilst exercising, stop immediately and
begin cooling down.
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the weight system.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
IMPORTANT PRECAUTIONS
Wall

4
BEFORE YOU BEGIN
Thank you for selecting the versatile WESLO®GYM
750 weight system. The weight system offers a selec-
tion of weight stations designed to develop every
major muscle group of the body. Whether your goal is
to tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
weight system will help you to achieve the results you
want.
For your benefit, read this manual carefully before
using the weight system. If you have questions after
reading this manual, see the front cover of this manu-
al. To help us assist you, please note the product
model number and serial number before contacting us.
The model number is WLEVSY1825.0. The serial
number can be found on a decal attached to the
weight system (see the front cover of this manual for
the location of the decal).
Before reading further, please review the drawing
below and familiarise yourself with the parts that are
labelled.
Foot Plate
Weight Stack
High Pulley Station
Lat Bar
Leg Lever
Butterfly Arm/Press Arm
Seat
Backrest
Anchor Hole
Weight Stack Lock
Press Frame Lock
ASSEMBLED DIMENSIONS:
Height: 79 in. / 200 cm
Width: 37 in. / 93 cm
Depth: 47 in. / 119 cm

5
Before beginning assembly, carefully read the
following information and instructions:
•Assembly requires two people.
•Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
•Tighten all parts as you assemble them, unless
instructed to do otherwise.
•As you assemble the weight system, make sure
all parts are oriented as shown in the drawings.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The following tools (not included) are required
for assembly:
• two adjustable spanners
• one rubber mallet
• one standard screwdriver
• one Phillips screwdriver
• lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end span-
ners, or a set of ratchet spanners.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight system can be assembled suc-
cessfully by anyone. However, it is important to
realise that the versatile weight system has
many parts and that the assembly process will
take time. Most people find that by setting aside
plenty of time, assembly will go smoothly.
ASSEMBLY
1
2
68
59
59
Indent
Indent
These holes
are smaller
than on the
opposite side.
1.
Orient the Stabiliser (2) as shown with the indents
around the holes on the bottom. Attach the Base
(1) to the Stabiliser with two M10 x 65mm
Carriage Bolts (59) and two M10 Nylon Locknuts
(68). Do not tighten the Locknuts.
Insert two M8 x 63mm Carriage Bolts (58) into
the bottom of the Base (1). Note: It may be help-
ful to place tape over the bolt heads to hold
them in place.
FRAME ASSEMBLY
Before beginning assembly,be sure that
you have read and understand the infor-
mation in the box above.
1
58

6
2. Attach the Upright (3) to the Base (1) with the two
M8 x 63mm Carriage Bolts (58) and two M8
Nylon Locknuts (69). Donot tighten the
Locknuts.
Attach the Press Frame Lock (39) to the Upright
(3) with an M8 x 63mm Bolt (66), two M8
Washers (71), and an M8 Nylon Locknut (69). Do
not overtighten the Locknut; the Press Frame
Lock must be able to pivot easily.
2
3
1
17
37
70 57
2
68
68
10
71
69
66
71
3
58
39
69
Holes
3. Set two Weight Bumpers (17) over the indicated
holes in the Stabiliser (2). Insert two Weight
Guides (10) into the same holes. Make sure that
the indicated holes are closer to the bottom of
the Weight Guides. Secure the Weight Guides in
place with two M10 x 70mm Bolts (57), two M10
Washers (70), two 10mm x 12.5mm Spacers (37),
and two M10 Nylon Locknuts (68).
Tighten the M10 Nylon Locknuts (68) used in
steps 1 and 3.

7
75
77
76
8
57
3
68
6
6. Attach the Seat Frame (8) to the Upright (3) with
two M10 x 70mm Bolts (57) and two M10 Nylon
Locknuts (68).
Attach the Bumper (75) to the Seat Frame (8)
with an M4 x 19mm Self-tapping Screw (76) and
an M4 Washer (77).
10
68
70
63
69
62
3
4
70
5
4
14
312
15
10
Lubricate
4. Slide the eight Weights (15) onto the Weight
Guides (10), with the slot for the Weight Pin (not
shown) on the bottom and on the side away from
the Upright (3).
Insert the Weight Tube (12) into the Weights (15).
Lubricate the indicated holes in the Top Weight
(14) with grease. Slide the Top Weight onto the
Weight Guides (10).
5. Attach the Top Frame (4) to the Upright (3) with
two M8 x 68mm Bolts (63) and two M8 Nylon
Locknuts (69). Do not tighten the Locknuts .
Attach the Top Frame (4) between the Weight
Guides (10) with an M10 x 155mm Bolt (62), two
M10 Washers (70), and an M10 Nylon Locknut
(68).
Tighten the Nylon Locknuts (68, 69) used in
steps 2 and 5.

8
9. Apply grease to the indicated post on the Left
Arm (7). Slide a 25mm x 68mm Round Bushing
(28) onto the post on the Arm; make sure that
the lip on the Bushing is oriented as shown.
Attach an Arm Pad (20) to the Left Arm (7) with
two M6 x 58mm Screws (65) and two M6
Washers (73).
Repeat this step with the Right Arm (6).
8. Apply grease to an M10 x 125mm Bolt (64).
Orient the Press Frame (5) with the bracket on
the side shown. Attach the Press Frame to the
Top Frame (4) with the Bolt, two M10 Washers
(70), and an M10 Nylon Locknut (68). Do not
overtighten the Locknut; the Press Frame
must be able to pivot easily.
7. Apply grease to an M10 x 70mm Bolt (57). Attach
the Leg Lever (9) to the Seat Frame (8) with the
Bolt and an M10 Nylon Locknut (68). Do not
overtighten the Locknut; the Leg Lever must
be able to pivot easily. 9
8
68
57
Grease
7
64
70
70
68
4
5
8
20
7
65
6
28
Post
Lip
73
73
9
Bracket
ARM ASSEMBLY
Grease

9
12. Route the High Cable (50) over a 90mm Pulley
(34) and down through the Top Frame (4). Attach
the Pulley and a Cable Trap (36) to the bracket
on the Top Frame with an M10 x 52mm Bolt (52)
and an M10 Nylon Locknut (68). Make sure the
Cable Trap is oriented to hold the Cable in the
groove of the Pulley.
13. Route the High Cable (50) under a 90mm Pulley
(34). Attach the Pulley,aCable Trap (36), and
two Finger Guards (35) to the second set of holes
from the top of the two Pulley Plates (44) with an
M10 x 52mm Bolt (52) and an M10 Nylon Locknut
(68). Make sure that the Cable Trap is oriented
to hold the Cable in the groove of the Pulley.
10. Insert the post on the Left Arm (7) through the
hole in the Press Frame (5). Make sure the Arm
isbehind the indicated bracket on the Press
Frame.
Slide a 25mm Washer (29) over the post on the
Left Arm (7). Attach an M6 x 43mm Bolt (61) to
the post with an M6 Nylon Locknut (72). Make
sure the Locknut and the head of the Bolt are
over the edge of the Washer, as shown in the
inset drawing.
Press a 25mm Round Outer Cap (27) onto the
top of the post on the Left Arm (7).
Repeat this step with the Right Arm (6).
11. See the CABLE DIAGRAM on page 17 for prop-
er cable routing.
Locate the High Cable (50). Route the threaded
shaft end of the Cable up through the Top Frame
(4) and over a 90mm Pulley (34). Attach the
Pulley inside the Top Frame with an M10 x 65mm
Bolt (55), two M10 Washers (70), two M10 x
12.5mm Spacers (37), and an M10 Nylon Locknut
(68).
27
29
72
7
6
5
10
61
36
52
50
34
68 4
50
34
37
37
70
70
68
55 4
11
68
44
36
44 35
35
34
50
12
13
52
CABLE ASSEMBLY
29
61 72
Post
Bracket

10
16. Locate the Press Cable (49). Slide the Cable
onto the hook on the Left Arm (7).
17. Apply grease to an M10 x 78mm Bolt (54). Attach
the Pulley Arm (38) to the Upright (3) with the Bolt
and an M10 Nylon Locknut (68). Do not over-
tighten the Locknut; the Pulley Arm must be
able to pivot easily.
Wrap the Press Cable (49) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), an M10
Washer (70), and two Finger Guards (35) to the
indicated side of a Pulley Arm (38) with an M10 x
52mm Bolt (52) and an M10 Nylon Locknut (68).
Make sure that the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
15. Attach the end of the High Cable (50) to the
Small “U”-bracket (11) with an M8 Washer (71)
and an M8 Nylon Locknut (69). Note: Do not
completely tighten the Locknut; it should be
threaded onto the Cable so that two threads
show past the Locknut, as shown in the inset
drawing.
Attach the Small “U”-bracket (11) to the Weight
Tube (12) with an M8 x 45mm Bolt (60) and an
M8 Nylon Locknut (69). Do not overtighten the
Locknut; the Weight Tube must be able to
pivot in the Small “U”-bracket.
14. Wrap the High Cable (50) over a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Top Frame (4) with an M10 x 46mm
Bolt (53) and an M10 Nylon Locknut (68).
68
50
34 35
35
4
53
14
11
71 60
69
12
15
7
35
35
34
68
16
17
50
69
11
49
Hook
70
49
36 38
52
54
3

11
19. Apply grease to an M10 x 78mm Bolt (54). Attach
the Pulley Arm (38) to the Upright (3) with the Bolt
and an M10 Nylon Locknut (68). Do not over-
tighten the Locknut; the Pulley Arm must be
able to pivot easily.
Wrap the Press Cable (49) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), an M10
Washer (70), and two Finger Guards (35) to the
indicated side of a Pulley Arm (38) with an M10 x
52mm Bolt (52) and an M10 Nylon Locknut (68).
Make sure that the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
18. Wrap the Press Cable (49) under a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Double “U”-bracket (42) with an M10 x
46mm Bolt (53) and an M10 Nylon Locknut (68).
34
53
68
49
35
42
35
18
35
36
49
52
38
68
68 3
54
34
35
70
19
20. Slide the end of the Press Cable (49) onto the
hook on the Right Arm (6). 49
6
20
21. Locate the Short Cable (47). Attach the eyelet
on the Cable to the Base (1) with an M10 x
70mm Bolt (57), an M10 Washer (70), and an
M10 Nylon Locknut (68). Do not overtighten the
Locknut.
57
70
68
47
1
21

12
23. Attach the end of the Short Cable (47) to the “U”-
bracket (43) with an M8 Washer (71) and an M8
Nylon Locknut (69). Note: Do not completely
tighten the Locknut; it should be threaded
onto the Cable so that two threads show past
the Locknut, as shown in the inset drawing.
24. Locate the Low Cable (48). Attach the Cable
inside the Base (1) with an M10 x 65mm Bolt
(55), two M10 Washers (70), two 10mm x 22mm
Spacers (51), and an M10 Nylon Locknut (68).
22. Wrap the Short Cable (47) over a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Double “U”-bracket (42) with an M10 x
46mm Bolt (53) and an M10 Nylon Locknut (68). 53
47
35
35
34
68
42
22
47
71
69
43
23
51
68
1
70
24
48
25. Route the Low Cable (48) over a 90mm Pulley
(34). Attach the Pulley,aCable Trap (36), and
two Finger Guards (35) to the second set of holes
from the bottom of the two Pulley Plates (44) with
an M10 x 52mm Bolt (52) and an M10 Nylon
Locknut (68). Make sure that the Cable Trap is
oriented to hold the Cable in the groove of the
Pulley.
44
52
35
36 34
35
48
68
25
47
69
43
55 70

13
27. Route the Low Cable (48) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), and
two Finger Guards (35) to the lower set of holes
in the “U”-bracket (43) with an M10 x 52mm Bolt
(52) and an M10 Nylon Locknut (68). Make sure
that the Cable Trap is oriented to hold the
Cable in the groove of the Pulley.
28. Route the Low Cable (48) under a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), and
two Finger Guards (35) to the Upright (3) with an
M10 x 100mm Bolt (46), two M10 Washers (70),
and an M10 Nylon Locknut (68). Make sure that
the Cable Trap is oriented to hold the Cable in
the groove of the Pulley.
26. Wrap the Low Cable (48) under a 90mm Pulley
(34). Attach the Pulley and two Finger Guards (35)
tothe bracket on the Base (1) with an M10 x
46mm Bolt (53) and an M10 Nylon Locknut (68).
35
35
68
34
1
48
53
26
34
48
35
36
35
52 43
68
27
70
48
36
70 68
35
35
34
3
28
29. Attach the Low Cable (48) to the Leg Lever (9)
with the M8 x 64mm Shoulder Bolt (56), an M8
Washer (71), and an M8 Nylon Locknut (69).
71
9
69
46
56
48
29

33. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in
ADJUSTMENTS, on the next page.
Before using the weight system, pull each cable a few times to make sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly,find and correct the problem. IMPORTANT: If
the cables are not properly routed, they may be damaged when heavy weight is used. See the CABLE
DIAGRAM on page 17 of this manual for proper cable routing. If there is any slack in the cables, you
will need to remove it by tightening the cables; see TROUBLESHOOTING AND MAINTENANCE on
page 18.
14
31. Attach the Seat (19), oriented as shown, to the
Seat Frame (8) with four M6 x 16mm Screws
(40).
32. Slide a Pad Tube (45) through the hole in the Leg
Lever (9). Slide two Round Pads (21) onto the
ends of the Pad Tube.
Repeat this step with the other Pad Tube (45)
and the Seat Frame (8).
30. Attach the Backrest (18) to the Upright (3) with
two M6 x 63mm Screws (67) and two M6
Washers (73).
18
73
73
3
40
40
67
67
19
Narrow
End
8
30
31
21
21
45
45
9
8
32
SEAT ASSEMBLY

15
This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the cor-
rect form for each exercise.
Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediate-
ly. The weight system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ATTACHING THE LAT BAR
Attach the Lat Bar (31) to the High Cable (50) with a
Cable Clip (33). Remove the Lat Bar when perform-
ing an exercise that does not require it.
33
50
31
CHANGING THE WEIGHT SETTING
Tochange the weight setting, insert a Weight Pin (16)
under the desired Weight (15) until the bent end of
the Weight Pin is touching the Weights. Turn the bent
end downward. The weight setting of each weight
stack can be changed from 6 pounds to 106 pounds,
in 12.5-pound increments. Note: Due to the cables
and pulleys, the amount of resistance at each
exercise station may vary from the weight setting.
Use the WEIGHT RESISTANCE CHART on page 16
to find the approximate amount of resistance at
each weight station.
CONVERTING THE ARMS
To use the Arms (6, 7) as butterfly arms, remove the
“L”-pins (30), and engage the Press Frame Lock (39)
into the Press Frame (5).
To use the Arms (6, 7) as press arms, disengage the
Press Frame Lock (39), and insert the “L”-pins (30)
into the holes in the Press Frame (5) and Arms.
16
15
ADJUSTMENTS
30
5
39
7
6

16
WEIGHT RESISTANCE CHART
The chart below shows the approximate weight resistance at each exercise station. “Top” refers to the 6-lb. top
weight. The other numbers refer to the 12.5-lb. weight plates. Weight resistance shown for the butterfly arm sta-
tion is for each butterfly arm. Note: The actual resistance at each station may vary due to differences in
individual weight plates as well as friction between the cables, pulleys, and weight guides.
WEIGHT
Top
1
2
3
4
5
6
7
8
HIGH
PULLEY
(lbs.)
18
32
46
59
75
92
109
121
132
PRESS ARM
(lbs.)
26
41
56
73
87
106
120
130
142
BUTTERFLY ARM
(lbs.)
21
28
37
48
60
74
89
99
109
LEG LEVER
(lbs.)
36
51
69
86
109
132
148
164
184
Note: 1 lb. = 0.454 kg

The cable diagrams below show the proper routing of the Short Cable (47), the Low Cable (48), the Press Cable
(49), and the High Cable (50). Use the diagrams to make sure that the cables have been assembled correctly. If
the cables have not been correctly routed, the weight system will not function properly and damage may occur.
The numbers show the correct route for each cable.
High Cable (50)
CABLE DIAGRAMS
4
4
1
2
1
2
5
5
6
5
4
3
2
1
Press Cable (49)
Low Cable (48)
Short Cable (47)
33
1
2
3
17

TROUBLESHOOTING AND MAINTENANCE
18
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight
system, can stretch slightly when it is first used. If
there is slack in the cables before resistance is felt,
the cables should be tightened.
Slack can be removed by moving a 90mm Pulley
(34), the Cable Trap (36), and two Finger Guards (35)
to a set of holes closer to the centre of the two Pulley
Plates (44). Remove the M10 Nylon Locknut (68) and
the M10 x 52mm Bolt (52) and re-attach the Pulley,
Cable Trap, and Finger Guards to the new set of
holes in the Pulley Plates with the Bolt and Locknut.
Slack can also be removed by moving the 90mm
Pulley (34), the Cable Trap (36), and two Finger
Guards (35) to the higher set of holes in the “U”-brack-
et (43). Remove the M10 Nylon Locknut (68) and the
M10 x 52mm Bolt (52) and re-attach the Pulley,the
Cable Trap, and two Finger Guards to the higher set
of holes in the “U”-bracket with the Bolt and Locknut.
Slack can also be removed from the cables by tighten-
ing the M8 Washer (71) and M8 Nylon Locknut (69)
attaching the Short Cable (47) to the “U”-bracket (43).
The High Cable (not shown) and the Small “U”-bracket
(not shown) can be adjusted in the same manner.
Make sure that the cables are not too tight or the
Top Weight (not shown) will be lifted off the weight
stack.
68
34
35
35
36
44
52
47
35
52
68
69
71
43
34
36
35

19
NOTES

ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Tel:
Outside the UK: 0 (044) 113 387 7133
Fax: [phone]
Please provide the following information when ordering replacement parts:
• the MODEL NUMBER of the product (WLEVSY1825.0)
• the NAME of the product (WESLO GYM 750 weight system)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING
attached at the centre of this manual)
Part No. 233986 R1005B Printed in China © 2005 ICON IP, Inc.
08457 089 009