Weslo Gym 1000 User manual

USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Model No.WLEVSY98110
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
www.iconeurope.com
Visit our website at
QUESTIONS?
As a manufacturer, we are
committed to providing com-
plete customer satisfaction. If
you have questions, or if there
are missing or damaged parts,
please call:
Or write:
ICON ealth & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: [e-mail]
08457 089 009
All manuals and user guides at all-guides.com
all-guides.com

2
TABLE OF CONTENTS
IMPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSEMB Y ...............................................................................5
ADJUSTMENT ...........................................................................15
WEIGHTRESISTANCECHART..............................................................17
TROUB ESHOOTINGANDMAINTENANCE ...................................................18
CAB EDIAGRAM.........................................................................19
PART IST ..............................................................................22
EXP ODEDDRAWING ....................................................................23
ORDERINGREP ACEMENTPARTS ..................................................BackCover
Note: A PART IDENTIFICATION CHART is attached in the centre of this manual. Remove the PART IDENTIFI-
CATION CHART before beginning assembly.
WES O is a registered trademark of ICON Health & Fitness, Inc.
All manuals and user guides at all-guides.com

3
1. Read all instructions in this manual and in
the accompanying literature before using the
weight system. Use the weight system only
as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight system are ade-
quately informed of all precautions.
3. The weight system is intended for home use
only. Do not use the weight system in a com-
mercial, rental, or institutional setting.
4. Use the weight system only on a level sur-
face. Cover the floor or carpet beneath the
weight system to protect the floor.
5. Make sure all parts are properly tightened
each time the weight system is used.
Replace any worn parts immediately.
6. Keep children under the age of 12 and pets
away from the weight system at all times.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protec-
tion when using the weight system.
9. The weight system is designed to support a
maximum user weight of 114 kg (250 lbs.). Do
not place more than 57 kg (125 lbs.) on the
weight carriage.
10. Never release the press arm, butterfly arms,
leg lever, lat bar, or nylon strap whilst
weights are raised; the weights will fall with
great force.
11. Make sure that the cables remain on the pul-
leys at all times. If the cables bind whilst you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.
12. Always stand on the foot plate when per-
forming an exercise that could cause the
weight system to tip.
13. Always disconnect the lat bar from the
weight system when performing an exercise
that does not use the lat bar.
14. If you feel pain or dizziness at any time
whilst exercising, stop immediately and
begin cooling down.
15. The decal shown below has been placed on
the weight system in the indicated location. If
the decal is missing or illegible, please call
our Customer Service Department at 08457
089 009 to order a free replacement decal.
Apply the decal in the indicated location.
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the weight system.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
IMPORTANT PRECAUTIONS
All manuals and user guides at all-guides.com

4
BEFORE YOU BEGIN
ASSEMB ED
DIMENSIONS:
Height: 193 cm (76 in.)
Width: 94 cm (37 in.)
ength: 122 cm (48 in.)
Foot Plate
ow Pulley Station
High Pulley Station
at Bar
eg ever
Butterfly Arms
Press Arm
Weight Carriage
Seat
Backrest
Thank you for selecting the versatile WES O®GYM
1000 weight system. The GYM 1000 weight system
offers a selection of weight stations designed to devel-
op every major muscle group of the body. Whether
your goal is to tone your body, build dramatic muscle
size and strength, or improve your cardiovascular sys-
tem, the WES O®GYM 1000 will help you to achieve
the specific results you want.
For your benefit, read this manual carefully before
using the weight system. If you have questions after
reading this manual, please call our Customer Service
Department at 0845 089 009. To help us assist you,
please note the product model number and serial
number before calling. The model number is
WEVSY98110. The serial number can be found on a
decal attached to the weight system (see the front
cover of this owner's manual for the location).
Before reading further, please familiarise yourself with
the parts that are labelled in the drawing below.
All manuals and user guides at all-guides.com

5
1
56
3
5
51
51
Indents
14
127
4
1. Before beginning assembly, make sure you
have read and understand the information in
the box above.
Press a 50mm Square Inner Cap (27) into the
end of the Base (4). Press a 50mm Square Outer
Cap (51) onto each end of the Stabiliser (5).
Insert two M8 x 63mm Carriage Bolts (1) up
through the Base (4). Insert two M8 x 67mm
Carriage Bolts (14) up through the Stabiliser (5).
Note: Make sure the indents around the holes
in the Stabiliser are on the bottom.
Slide the bracket end of the Base (4) onto the M8
x 67mm Carriage Bolts (14) in the Stabiliser (5).
Slide the Rear Upright (56) onto the Carriage
Bolts. Hand tighten an M8 Nylon ocknut (3) onto
each Carriage Bolt.
FRAME ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
•Assembly requires two people.
•Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
•Tighten all parts as you assemble them, unless
instructed to do otherwise.
•As you assemble the weight system, make sure
all parts are oriented as shown in the drawings.
• For help identifying small parts, use the PART
IDENTIFICATION C ART in the centre of this
manual.
The following tools (not included) are required
for assembly:
• two adjustable spanners
• one rubber mallet
• one standard screwdriver
• one Phillips screwdriver
• lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight system can be assembled suc-
cessfully by anyone. However, it is important to
realise that the versatile weight system has
many parts and that the assembly process will
take time. Most people find that by setting aside
plenty of time, assembly will go smoothly.
ASSEMBLY
All manuals and user guides at all-guides.com

6
2. Refer to drawing 2a. Press a 25mm Round Inner
Cap (49) into each end of the weight tube on the
Weight Carriage (19). Note: Make sure the
Square Slider Bushings (70) are assembled to
the Weight Carriage and Weight Stop (67).
Turn the Weight Stop (67) so that the indicated
hole is on the side shown and the Square Slider
Bushing (70) is on top. Slide the Weight Stop
onto the Rear Upright (56).
Refer to drawing 2b. Attach the Weight Stop
(67) to the Rear Upright (56) with an M8 x 70mm
Bolt (11) and an M8 Nylon ocknut (3).
Orient the Weight Carriage (19) as shown. Slide
the Weight Carriage onto the Rear Upright (56).
Press a 25mm Square Inner Cap (65) into the
Front Upright (42). Slide the Front Upright onto
the M8 x 63mm Carriage Bolts (1) in the Base
(4). Hand tighten an M8 Nylon ocknut (3) onto
each Carriage Bolt. Do not tighten the Nylon
Locknuts yet.
3. Press a 50mm Square Inner Cap (27) into the top
of the Rear Upright (56). Press a 45mm Square
Inner Cap (44) into each end of the crossbar on
the Top Frame (55). Press two 25mm Round
Inner Caps (49) into the top of the crossbar.
Attach the Top Frame (55) to the Front Upright
(42) with two M8 x 67mm Bolts (72), a Support
Plate (8), and two M8 Nylon ocknuts (3). Attach
the Top Frame to the Rear Upright (56) in the
same manner.
Tighten the Nylon Locknuts (3) used in steps
1–3.
2
42
67
70
19
56
Hole
65
3
1
4
70
70
67
19
49
49
70
2a
2b
3
19
11
67
56
3
72
72
8
44
44
49
27
55
56 42
3
Crossbar
3
8
All manuals and user guides at all-guides.com
all-guides.com

7
46
3
22
Handle
17
44
49
5
48
60
47
Welded
Brackets
6
5. Press a 45mm Square Inner Cap (44) into the top
of one of the Press Arms (46). Press a 25mm
Round Inner Cap (49) into each end of the handle
on the Press Arm. Attach the Press Arm to one
side of the Press Frame (17) with two M8 x
63mm Bolts (22) and two M8 Nylon ocknuts (3).
Assemble the other Press Arm (46) in the same
manner.
6. Identify the eft Arm (47) and Right Arm (48).
Note the position of the welded bracket on each
Arm. Arm identification is important for step 7.
Press a Butterfly Arm Bushing (60) into each Arm.
4. Press a 25mm Plastic Bushing (26) onto each
welded spacer on the Press Frame (17). Slide the
Press Frame onto the Base (4) so the Plastic
Bushings are aligned with the indicated tube in
the base. Note: This will be a tight fit; the
Plastic Bushings should fit over the ends of
the tube in the Base.
ubricate an M10 x 198mm Bolt (59). Attach the
Press Frame (17) to the Base (4) with the Bolt, two
M10 Washers (9), and an M10 Nylon ocknut (21).
Note: Do not overtighten the Nylon Locknut;
the Press Frame must be able to pivot easily.
4
4
Tube
Welded
Spacers
17 ubricate
21
926
9
59
ARM ASSEMBLY
All manuals and user guides at all-guides.com

8
CABLE ASSEMBLY 8
9
58
58
55
16
21
Rod
Ball 15 73
73
Small
Tabs
23
8. During steps 9 through 22, refer to the CABLE
DIAGRAM on page 19 of this manual to verify
proper cable routing. Before beginning this sec-
tion, identify the Short Cable (23) and the ong
Cable (58) by comparing the ends of the cables.
IMPORTANT: Whilst assembling the cables, do
not overtighten the bolts and nuts securing
the pulleys. The pulleys must turn freely.
9. Locate the Long Cable (58). Route the ong
Cable around a 90mm Pulley (15). Attach the
Pulley and two Pulley Covers (73) to the Top
Frame (55) with an M10 x 97mm Bolt (16) and an
M10 Nylon ocknut (21). Note: The small tabs
on the Pulley Covers must be on top. Make
sure that the Cable is between the Pulley and
the rod on the Top Frame and that the end of
the Cable with the ball is on the indicated side
of the Rod.
7. ubricate both axles on the Top Frame (55).
Slide the Right Arm (48) onto the right axle of the
Top Frame (55). Note: Be careful not to con-
fuse the Right Arm with the Left Arm (47);
refer to step 6 to identify the Right Arm. Make
sure that the upper end of the Right Arm is
behind the indicated bracket on the Top
Frame.
Tap two 25mm Retainers (63) and a 25mm Round
Cover Cap (62) onto the right axle of the Top
Frame (55). Make sure that the teeth on the
Retainers bend toward the Cover Cap, as
shown in the inset drawing.
Attach the eft Arm (47) in the same manner.
Press two 45mm Square Inner Caps (44) into the
lower ends of the eft and Right Arms (47, 48).
Wet the lower end of each Arm with soapy water.
Slide a arge Foam Pad (45) onto the lower end of
each Arm.
7
Bracket
ubricate
Axle
45
47
55
48
45
44
63
62
63
55
62
All manuals and user guides at all-guides.com

9
12
48 21
50 7
6
58
12. Route the ong Cable (58) around a “V”-Pulley
(6). Attach the Pulley and the ong Cable Trap
(50) to the Right Arm (48) with an M10 x 60mm
Bolt (7) and an M10 Nylon ocknut (21). Make
sure that the Cable is in the groove of the
Pulley and that a Long Cable Trap (50) is
turned to hold the Cable in place.
13. Refer to the inset drawing. Attach the Pulley
Bracket (20) to the bracket on the Top Frame (55)
with an M8 x 115mm Bolt (64) and an M8 Nylon
ocknut (3). Note: The Pulley Bracket is pre-
assembled with a 90mm Pulley (15) and a
Cable Trap (66).
Route the ong Cable (58) around the 90mm
Pulley (15) attached to the Pulley Bracket (20).
Make sure that the Cable is in the groove of
the Pulley and that the Cable Trap (66) is
turned to hold the Cable in place. Make sure
that the M10 x 45mm Bolt (12), securing the
Pulley and Cable Trap to the Pulley Bracket, is
properly tightened and that the Pulley Bracket
can pivot freely.
13
58
66
15 71
20
64
55
3
20
11
10
50
58
7
47
58
21
7
21
650
6
42
10. Wrap the ong Cable (58) around a “V”-Pulley
(6). Attach the Pulley and a ong Cable Trap (50)
to the bracket on the Front Upright (42) with an
M10 x 60mm Bolt (7) and an M10 Nylon ocknut
(21). Make sure that the Cable Trap is posi-
tioned to hold the Cable in the groove of the
Pulley.
11. Route the ong Cable (58) around a “V”-Pulley
(6). Attach the Pulley and a ong Cable Trap (50)
to the eft Arm (47) with M10 x 60mm Bolt (7)
and an M10 Nylon ocknut (21). Make sure that
the Cable is in the groove of the Pulley, and
that the Cable Trap is positioned to hold the
Cable in place.
All manuals and user guides at all-guides.com

10
16. Attach the ong Cable (58) to the Weight
Carriage (19) with an M10 x 20mm Bolt (69) and
an M10 Nylon ocknut (21).
16
19
21 69
58
14. Wrap the ong Cable (58) under a 90mm Pulley
(15). Attach the Pulley and a pair of Pulley
Covers (73) to the upper hole in the ong “U”-
Bracket (57) with an M10 x 50mm Bolt (12) and
an M10 Nylon ocknut (21). Make sure that the
large tabs on the Pulley Covers are on the
side shown.
15. Route the ong Cable (58) around a 90mm Pulley
(15). Attach the Pulley to the bracket on the Top
Frame (55) with an M10 x 45mm Bolt (71) and an
M10 Nylon ocknut (21). Make sure that the
Cable is in the groove of the Pulley and that
the Cable and Pulley move smoothly.
14
58
73
73
57
12
21
arge
Tabs
15
15
71
15
58
Bracket
55
21
All manuals and user guides at all-guides.com