Westinghouse SR80SP01H-08 User manual

8.5"
11"
Instruction Manual
Model: SR80SP01H-08
www.westinghousesolarlights.com
For assistance with assembly or instruction, parts and customer service, call:
U.S.A. & Canada only: 1-844-551-0680
8am - 5pm Monday - Friday, Central Standard Time Or email: [email protected]
, WESTINGHOUSE, are trademarks of Westinghouse Electric Corporation. Used
under license by Sky Rich Star Limited. All Rights Reserved.
EN | 1EN | 4
SOLAR LED LIGHT
WITH BLUETOOTH SPEAKER
®
TRADEMARK ATTRIBUTION FOOTNOTE
Whenever the Bluetooth Trademarks are used in a particular
piece, they must be attributed with an appropriate trademark
footnote. The recommended attribution footnote is as follows:
“The Bluetooth word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. And any use of such marks by
INTERNATIONAL DEVELOPMENT COMPANY is under license.
Other trademarks and trade names are those of their respective
owners.”
NOTE: The Bluetooth brand elements may not be used in a
fashion or manner that could impair or otherwise damage the
goodwill associated with the Bluetooth brand or the Fellow
Adopters (International Development Company). The
Bluetooth brand elements shall therefore not be used in
connection with products and services that do not enable any
Bluetooth wireless functionality or in connection with unlawful,
obscene, pornographic, excessively violent, hazardous,or
otherwise poor-taste activities.
®
®
®
®
®

WARNING:
1. This product is not a toy and contains small parts. Close supervision is necessary when
this unit is used near children.
2. To reduce the risk of electrical shock, do not put the unit in water or other liquids. Do
not place or store appliance where it can fall or be pulled into a tub or sink.
3. To clean, use a soft dry cloth.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmfull interference to radio
communications. However, there is no guarantee that interference will not occur during
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment.
PARTS AND SPECIFICATIONS
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
8.5"
11"
®
HOW TO PAIR WITH A SMART DEVICE:
1. Press power button (E) for 2 seconds to turn on speaker and initiate bluetooth pairing
mode.
2. Activate bluetooth on your smart device and find device named “Westinghouse SR80”.
Press to pair.
3. Once paired, select audio from your device and play through the solar LED light speaker.
4. Press power button (E) quickly to pause or play music.
5. Press power button (E) two times quickly to disconnect the bluetooth .
6. Press power button (E) for 2 seconds to turn off speaker.
NOTE: Adjust the volume and select music with your smart device.
HOW TO OPERATE FLASH LIGHT :
There are two ways to turn on the flash light:
1. Press light button (C) for 2 seconds to turn on the flash light for high light output
(100LM). Press again, a 2nd time, for low light output (50LM), press a 3rd time for strobe
light and a 4th time to turn off.
2. Press power button (E) for 2 seconds, then press the flash light button (C) to power on
the light.
NOTE: Do not look directly at the light.
®
®
HOW TO OPERATE THE MICROPHONE (G):
When the bluetooth of the smart device connected the light, microphone (G) can be used
for hands-free calling. Short press the power button (E) to answer the call and long press
the power button (E) for 2 seconds to reject the call.
®
A
B
D
F
G
CHARGING INSTRUCTIONS
CHARGING METHOD:
1) USB charging port (H)
Press the power button (E) and hold for 2
seconds to turn light OFF. Use USB cable (J)
to connect the external 5V power supply to
charge the light. (2 hours minimum needed
to fully charge light.)
2) Solar panel (A) charging
Press the power button (E) and hold for 2
seconds to turn light OFF. Place solar
panel (A) in direct sunlight and allow to
charge 18-20 hours for a full charge.
I
H
EN | 3EN | 2
C
E
J
I
Solar PanelA-
Flash LightB-
Flash Light ButtonC-
3W Bluetooth SpeakerD- ®
Power ButtonE-
LED IndicatorF-
MicrophoneG-
USB Charging PortH-
LanyardI-
Micro USB CableJ-
A
H
MULTI-COLOR LED INDICATOR (E) INSTRUCTIONS:
1) RED LIGHT indicates solar LED light is charging. USB plug or solar charging.
The red light will remain on until solar LED light is fully charged and turn off.
2) BLUE LIGHT indicates Bluetooth status. Turn on the Bluetooth speaker and once in
search mode or pairing mode the blue light flashes. After the smart device is connected
with the speaker, the blue light will stop flashing. When music is playing, the blue light
remains on.
NOTE: The solar LED light has an automatic reconnection feature. When the solar LED
light is connected to the smart device and then restarted, if the previously connected
device is in the connection range, the product will automaticlly connect with the previously
connected smart device first. In this case, if you want to connect with a (new) smart device,
the smart device that is connected to the solar LED light needs to be disconnected first.
Double click the power button (E), then the solar LED light can be connected with a (new)
smart device.
LOW BATTERY TIPS.
When the light experiences a low battery, it will voice a warning "low battery, please
charge". Immediately charge with USB plug provided, or place light outside in direct
sunlight. If product is not charged in time, product will shut off. Please keep the speaker
in a dry environment when using USB charging.
NOTE: Bluetooth speaker (F) and flash light (B) can operate independently
®
RUN TIME
Speaker 6.5 HOURS
Flash light 5 HOURS
Speaker & Flash light 3 HOURS
NOTE: Do not allow an open USB charging port to get exposed to water or any other
liquids keep USB charging port closed when not in use.
G
C
E
NOTE: This product includes a built-in lithium battery and cannot be replaced.
WARNING: Do not dispose of lithium batteries in municipal waste streams or by fire as
batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of
batteries in accordance with Local, State, and Federal regulations. Do not mix old and new
batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium,
nickel metal hydride or lithium ion) batteries .

PARTES Y ESPECIFICACIONES
INSTRUCCIONES DE OPERACIÓN
INSTRUCCIONES DE OPERACIÓN
8.5"
11"
HOW TO PAIR WITH A SMART DEVICE:
1. Press power button (E) for 2 seconds to turn on speaker and initiate bluetooth pairing
mode.
2. Activate bluetooth on your smart device and find device named “Westinghouse SR80”.
Press to pair.
3. Once paired, select audio from your device and play through the solar LED light speaker.
4. Press power button (E) quickly to pause or play music.
5. Press power button (E) two times quickly to disconnect the bluetooth .
6. Press power button (E) for 2 seconds to turn off speaker.
NOTE: Adjust the volume and select music with your smart device.
HOW TO OPERATE FLASH LIGHT :
There are two ways to turn on the flash light:
1. Press light button (C) for 2 seconds to turn on the flash light for high light output
(100LM). Press again, a 2nd time, for low light output (50LM), press a 3rd time for strobe
light and a 4th time to turn off.
2. Press power button (E) for 2 seconds, then press the flash light button (C) to power on
the light.
NOTE: Do not look directly at the light.
®
®
®
HOW TO OPERATE THE MICROPHONE (G):
When the bluetooth of the smart device connected the light, microphone (G) can be used
for hands-free calling. Short press the power button (E) to answer the call and long press
the power button (E) for 2 seconds to reject the call.
Solar PanelA-
Flash LightB-
Flash Light ButtonC-
3W Altavoz BluetoothD- ®
Botón de EncendidoE-
LED IndicatorF-
MicrophoneG-
USB Puerto de CargaH-
LanyardI-
Lentes de LuzJ-
A
B
D
F
G
INSTRUCCIONES DE CARGA
I
H
ES | 3ES | 2
C
E
J
I
A
H
MÉTODO DE CARGA:
1) Puerto de carga USB (H)
Para apagar la luz, presione el botón de encendido (E)
y manténgalo presionado durante 2 segundos.
Emplee un cable USB (J) para conectar la fuente de
alimentación externa de 5V para cargar la luz.
(Mínimo 2 horas para cargar la luz completamente)
2) Panel solar (A) de carga:
Presione el botón de encendido (E) y manténgalo
presionado durante 2 segundos para apagar la luz.
Coloque el panel solar (A) a la luz solar directa y deje
que se cargue de 18 a 20 horas para una carga completo.
MULTI-COLOR LED INDICATOR (E) INSTRUCTIONS:
1) RED LIGHT indicates solar LED light is charging. USB plug or solar charging.
The red light will remain on until solar LED light is fully charged and turn off.
2) BLUE LIGHT indicates Bluetooth status. Turn on the Bluetooth speaker and once in
search mode or pairing mode the blue light flashes. After the smart device is connected
with the speaker, the blue light will stop flashing. When music is playing, the blue light
remains on.
NOTE: The solar LED light has an automatic reconnection feature. When the solar LED
light is connected to the smart device and then restarted, if the previously connected
device is in the connection range, the product will automaticlly connect with the previously
connected smart device first. In this case, if you want to connect with a (new) smart device,
the smart device that is connected to the solar LED light needs to be disconnected first.
Double click the power button (E), then the solar LED light can be connected with a (new)
smart device.
LOW BATTERY TIPS.
When the light experiences a low battery, it will voice a warning "low battery, please
charge". Immediately charge with USB plug provided, or place light outside in direct
sunlight. If product is not charged in time, product will shut off. Please keep the speaker
in a dry environment when using USB charging.
NOTE: Bluetooth speaker (F) and flash light (B) can operate independently
®
TIEMPO DE FUNCIONAMIENTO
Speaker 6.5 HORAS
Flash light 5 HORAS
Speaker & Flash light 3 HORAS
NOTE: Do not allow an open USB charging port to get exposed to water or any other
liquids keep USB charging port closed when not in use.
G
C
E
NOTA: Este producto incluye una batería de litio incorporada y no se puede reemplazar.
CUIDADO: No deseche las baterías de litio en la corriente de desechos municipales o por el
fuego, ya que las baterías pueden explotar. No abra, provoque cortocircuitos ni mutile las
baterías. Deseche las baterías de acuerdo con los reglamentos locales, estatales y federales.
No mezcle las baterías viejas con las nuevas. No mezcle las baterías alcalinas, estándar
(carbono-zinc) ni recargables (níquel-cadmio, níquel e hidruro metálico o ion litio).
ADVERTENCIA:
1. Este producto no es un juguete y contiene piezas pequeñas. Se requiere una supervisión
cuidadosa al usar esta unidad cerca de niños.
2. Para reducir el riesgo de descarga eléctrica, no coloque a unidad en agua u otros
líquidos. Utilice un paño suave y seco para limpiarla. No coloque ni almacene el aparato en
lugares donde se pueda caer o jalar hacia una bañera o lavabo.
NOTA:
Este equipo fue probado y se determinó que cumple con los Iímites para un dispositivo
digital de Clase B, de conformidad con la Parte 15 del Reglamento de la FCC. Estos límites
se diseñaron para proporcionar una protección razonable contra la interferencia dañina en
instalación residenciales. Este equipo genera, utilza y puede irradiar energía de
radiofrecuencia y si no se instala y utiliza apegándose al instructivo, puede causar
interferencia dañina en las radiocomunicaciones. Sin embargo, no se garantiza que no
ocurra interferencia en unaa instalación en particular. Si este equipo causa interferencia
dañina en la recepción de las señales de radio o televisión, lo cual puede determinarse al
encender y apagr el equipo, se insta al usuario a tratar de corregir la interferencia por
medio de una o más de las siquientes medidas:
- Reorientar o reubicar la antena receptora.
- Aumentar la distancia entre el equipo y el receptor.
- Conectar el equipo en un tomacoriente dentro de un circuito diferente al cual esté
conedado el receptor.
- Consultar al distribuidor o a untécnico experimentado en radio/televisión.
Este equipo cumple con la Parte 15 de los reglamentos de la FCC. Su operación está sujeta
a las siguientes dos condiciones:
1) Este dispositivo no puede causar interferencia dañina.
2) Este dispositivo debe acaptar cualquier interferencia que recita, incluida la interferencia
que pueda causar un funcionamiento indeseable.
ADVERTENCIA:
Los cambios y modificaciones no aprobados expresamente por la parte responsable de su
cumplimiento, podrían invalidar la autoridad del usuario para operar el equipo.
RF EXPOSURE: This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment.

NOTA SOBRE ATRIBUCIÓN DE LA MARCA REGISTRADA
Siempre que las marcas registradas de Bluetooth se utilizan
en un producto particular, deben contar con la adecuada
nota al pie de atribución de la marca registrada. La nota de
atribución recomendada es la siguiente: “La marca y los logos
de Bluetooth son marcas registradas propiedad de SIG, Inc.
Cualquier uso de esas marcas por parte de INTERNATIONAL
DEVELOPMENT COMPANY es bajo licencia. Otras marcas
registradas y nombres comerciales pertenecen a sus
respectivos propietarios.”
®
NOTA:
Los componentes de la marca de Bluetooth no se utilizarán
de ninguna forma o manera que pudiera perjudicar o dañar
de otra manera la buena fe vinculada a la marca de Bluetooth
o sus miembros asociados (International Development
Company). Los componentes de la marca de Bluetooth , por
consiguiente, no se utilizarán en relación con productos o
servicios que no habiliten funcionalidad inalámbrica alguna, o
en relación con actividades ilegales, obscenas, pornográficas,
de excesiva violencia, nocivas o de mal gusto por cualquier
otro concepto.
®
®
®
8.5"
11"
Manual de Instrucciones
Modelo: SR80SP01H-08
www.westinghousesolarlights.com
, WESTINGHOUSE, es una marca registrada de Westinghouse Electric Corporation.
Usado bajo licencia por Sky Rich Star Limited. Todos los derechos reservados.
Para recibir asistencia con el montaje o las instrucciones, repuestos y servicio al cliente,
llame a: (solo EE.UU. y Canadá) 1-844-551-0680
de 8am – 5pm de lunes a viernes, hora estándar central O envíe un correo electrónico a:
[email protected]
ES | 1ES | 4
LUZ LED SOLAR CON
ALTAVOZ BLUETOOTH
®