Wfly WFT08X User manual

INSTRUCTION MANUAL
WFT08X RADIO CONTROL SYSTEM PCMS 1024
NOTICE
Read the instructions before operation!
V2

WFT08X INSTRUCTION
Thank you for purchasing WFLY products!
WFT08X
SERVICE
1.Retailers to provide free maintenance for one year (apart from
artificial damage)
2. WFLY retailers will always provide life-long maintance

CATALOGUE
Contents-------------------------------------------------------------------
WFT08X Spare parts-----------------------------------------------------
Transmitter front----------------------------------------------------------
Transmitter back----------------------------------------------------------
Receiver for 2.4GHz-----------------------------------------------------
2.4GHz operation instructions-----------------------------------------
Receiver for FM ----------------------------------------------------------
Trainer function-----------------------------------------------------------
Flying safety warnings---------------------------------------------------
Features--------------------------------------------------------------------
Keys–-----------------------------------------------------------------------
Adjust the stick head----------------------------------------------------
C --------------------------hange the throttle direction of mode1 or 2
1. Model selecting---------------------------------------------------------
2. Model name-------------------------------------------------------------
3. Model setting-----------------------------------------------------------
4. ATL-----------------------------------------------------------------------
5. Modulation setting-----------------------------------------------------
6. Swash select-----------------------------------------------------------
7. Stick setting------------------------------------------------------------
.------------------------------------------------------------- 8 Adjustment
9. Reset setting-----------------------------------------------------------
10. Send data-------------------------------------------------------------
11. Receive data----------------------------------------------------------
12.Sound------------------------------------------------------------------
13. Contrast setting------------------------------------------------------
14.About ------------------------------------------------------------------
15. Language--------------------------------------------------------------
1. Monitor-------------------------------------------------------------------
2. Dual rate & Exponential-----------------------------------------------
3. Servo reverse-----------------------------------------------------------
4. End point-----------------------------------------------------------------
WFT08X INSTRUCTION
I
HELICOPTER
SYS SETTING
NORMAL SETTING
01
02
03
04
05
06
07
08
09
10
11
12
13
17
18
19
20
21
22
23
24
25
26
27
28
29
29
30
31
32
33
34

II
5. Sub trim----------------------------------------------------------------
6. Swash param setting------------------------------------------------
7. Auxiliary channels setting------------------------------------------
8. Throttle curve setting------------------------------------------------
9. Pitch curve setting---------------------------------------------------
10. Revolution mixing---------------------------------------------------
11. Trim step setting-----------------------------------------------------
12. Throttle cut setting--------------------------------------------------
13. Fly model switch-----------------------------------------------------
14. Throttle holding setting---------------------------------------------
15. Fail safe---------------------------------------------------------------
16. Time-------------------------------------------------------------------
17. Advanced-------------------------------------------------------------
(1). GYRO sens setting---------------------------------------------
(2). Throttle hovering setting--------------------------------------
(3). Pitch hovering setting------------------------------------------
(4). HI/LO PIT Setting-----------------------------------------------
(5). Trim offset setting----------------------------------------------
(6). DELAY------------------------------------------------------------
(7). Governor mixing------------------------------------------------
(8). Swash and THR mixing----------------------------------------
(9). Curve setting----------------------------------------------------
(10)-(14). PROG.NOR.MIX1-5------------------------------------------
(15)-(16). PROG.CUR.MIX1-2-------------------------------------------
(17). Throttle needle mixing----------------------------------------
WFT08X INSTRUCTION
ADVANCED
35
36
37
38
40
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
61
62
63

WFT08X INSTRUCTION
AIRPLANE
SYS SETTING
1.Model selecting---------------------------------------------------
2.Model name-----------------------------------------------------------
3.Model setting-------------------------------------------------------
4.Atl------------------------------------------------------------------------
5.AIL-2---------------------------------------------------------------------
6.Modulation setting----------------------------------------------
7.Stick setting--------------------------------------------------------
8.Adjustment-------------------------------------------------------------
9.Reset setting---------------------------------------------------------
10.Send data------------------------------------------------------------
11.Receive data-------------------------------------------------------
12.Sound-------------------------------------------------------------------
13.Contrast setting-----------------------------------------------
14.About-------------------------------------------------------------------
15.Language---------------------------------------------------------------
III
NORMAL SETTING
1.MONITOR----------------------------------------------------------------
2.DUAL RATE & EXPONENTIAL SETTING---------------------------
3.SERVO REVERSE------------------------------------------------------
4.END POINT--------------------------------------------------------------
5.SUB TRIM----------------------------------------------------------------
6.AUXILIARY CHANNELS SETTING----------------------------------
7.THROTTLE CURVE SETTING----------------------------------------
8.TRIM STEP SETTING--------------------------------------------------
9.FLAPERON--------------------------------------------------------------
10.FLAP TRIM-------------------------------------------------------------
11.AIL-DIFF----------------------------------------------------------------
12.ELEV-FLAP------------------------------------------------------------
67
68
69
70
71
72
73
74
75
76
77
78
79
79
80
81
82
83
84
85
86
87
89
90
91
92
93

WFT08X INSTRUCTION
IV
13.THROTTLE CUT SETTING-----------------------------------------
14.IDLE DOWN-----------------------------------------------------------
15.FAIL SAFE-------------------------------------------------------------
16.TIMER------------------------------------------------------------------
17.ADVANCED------------------------------------------------------------
1.CURVE SETTING-------------------------------------------------------
2-6.PROG.NOR.MIX1-5-------------------------------------------------
7-8.PROG.CUR.MIX1-2-------------------------------------------------
9.AIR BRAKE---------------------------------------------------------------
10.ELEVON------------------------------------------------------------------
11.AILVATOR----------------------------------------------------------------
12.V-TAIL-------------------------------------------------------------------
13.SNAP-ROLL-------------------------------------------------------------
14.DELAY------------------------------------------------------------------
15.THROTTLE NEEDLE MIXING---------------------------------------
16.GYRO SENS SETTING-----------------------------------------------
ADVANCED
94
95
96
97
98
99
102
103
104
105
106
107
108
109
110
111

Contents
1. WFT08X transmitter
2. 2.4GHz WFTRFS RF module
3. Battery holder for transmitter
4. Neckstrap
5. WFR09S 2.4GHz receiver
6.Li-po Voltage Regulator
WFT08X INSTRUCTION
01

WFT08X Spare Parts for 2.4GHz
1. Transmitter 2. WFTRFS
2.4GHz RF module
3. Battery Holder
4. Neckstrap
WFT08X INSTRUCTION
5. WFR09S receiver
02
6.li-po Voltage Regulator

TRANSMITTER FRONT VIEW
MODEL NO.: WFT08X
MODULATION: PCMS 1024/PPM
OUTPUT POWER:≤100mW(2.4GHz);
≤ 700mW(35-75MHz)
POWER SUPPLY: 1.2V x 8 (9.6V)
CURRENT DRAIN: 200mA
Band: 35, 36, 40, 41, 72,75MHz
TRANSMITTER FRONT VIEW
WFT08X INSTRUCTION
03
Antenna
Power Light RF Light
Buzzer
Switch B
Switch A
Switch C VA VB VC
Switch F
Trainer switch
Switch D
SwitchE
Decrease
Menu
Exit
Increase
Rudder trim
Elevator trim
Rudder/
elevator stick
LCD
OK
Neckstrap attachment
Down
Right
Up
Left
Aileron trim
Power switch
Throttle trim
Aileron/throttle stick
RF Antenna
Green light refers to power light
(when you power on the transmitter, Green light will be on)
Blue light refers to RF light
(The light will be on when RF is on and stay on normal work)
Hereunder issues are the reasons for RF light is off.
1. Doesn't insert RF module into transmitter
2. RF module is on coding
3. When you enter into SYS setting ( for example: Data Transfer)
4. The modulation of your RF is not compatible with your transmitter.

STATU S SE T
NOR MA L
Gre en LED li ghts :p ower
Ora nge LED l ights : incor rect in put sig nal
SET M ODE: ho ld SET an d po we r on r adi o
Gre en LED li ghts :f ail saf e
Ora nge LED l ights : code ma tchin g
Gre en LED gl itter s :fail s afe is se tting
Ora nge LED g litte rs :con de matc hing is s ettin g
12 BI TS DIGI TAL PROPO RT IO NAL R /C SYST EM
TRANSMITTER BACK VIEW
Handle
RF module
Battery
cover
DSC
Charge hole
WFT08X INSTRUCTION
04

The receiver is used for all WFLY transmitters.
WFR09S 9 Channel Receiver
1．AIL：Aileron (Channel 1)-------------------------
2．ELE：Elevator (Channel 2)----------------------
3．THR：Throttle (Channel 3)------------------------
4．RUD：Rudder (Channel 4)------------------------
5．GYR：Landing Gear/Gyro (Channel 5)----------
6．PIT：Pitch (Channel 6)------------------------------
7．AUX1：Auxiliary channel 1 (Channel 7)----------
8．AUX2：Auxiliary channel 2 (Channel 8)-----------
9．Power：Input 4.8-6V----------------------------------
RECEIVER
MODEL NO.: WFR09S
TYPE: 9 CH PPM/PCMS 1024/PCMS 4096
POWER SUPPLY: 4.8-6V
CURRENT DRAIN: 30mA
RECEIVER SENSITIVITY:-97dBm
BAND: 2.400GHz-2.4835GHz
05
WFT08X INSTRUCTION
This receiver has fail safe function.
Characteristic
Can effectively select the best signal
Enhance the reliability
Improve the response speed
;
Enhance the anti-interference
Increased use of range
(There are 9 rows needles, 3 needles in each row,
from the top needle to the bottom, the 3 needles are PCMS/PPM pulse, +5V and Ground.)

06
WFT08X INSTRUCTION
Fail safe set Code matching
2. Operation Instructions
1. Code matching
Flash
2.4GHz system can automatically recognize WFLY PCMS1024 and PPM.
B. Hold SET of the module, then press Power to start the transmitter. Press SET again to enter the code
matching function.The orange LED of the receiver lights up. Press SET and hold until the orange LED
flashes,indicating the receiver enters the code matching status.
C. If the code matches successfully, the green LED of the transmitter lights up.
The LED of the receiver is off.
The receiver is on. The red LED lights up. Wait for the powering up of
the transmitter.
The receiver is on. The green LED of the transmitter lights up.
The LED of the receiver is off.
3. Fail Safe Setting
The same setting for WFR07S and WFR09S
WFLY 2.4GHz Operation Instructions
A. Press SET to start the receiver. The orange LED flashes, indicating the receiver waits for the code
matching signal.
A. Power on receiver.
B. Press SET of the module then start transmitter and hold SET for 2 seconds. The green LED flashes, indicating
the transmitter enters the code matching status.
C. The Green LED of receiver flashes, the output data of transmitter is the data of Fail Safe Setting of the
receiver.
D. Due to the heavy interference or out of normal range, the receiver enters Fail Safe. The Red LED of the
receiver lights when it is in Fail Safe status.

The receiver is used for WFT09(S)/08X transmitter.
WFR08-P 8 Channel Software decoding Receiver (PPM)
WFT08X INSTRUCTION
RECEIVER
MODEL NO.: WFR08-P
TYPE: 8CH Software decoding PPM
POWER SUPPLY: 1.2V x 4 (4.8V)
CURRENT DRAIN: 20mA
WEIGHT: 19 g
DIMENSION: 44.88mm x27.90mm x16.39mm
BAND: 35, 36, 40, 41, 72,75MHz
There is the function of fail safe
07
7．AUX1：Auxiliary channel 1 (Channel 7)------------------
8．AUX2：Auxiliary channel 2 (Channel 8)-------------------
1．AIL：Aileron (Channel 1)-----------------------------------
2．ELE：Elevator (Channel 2)--------------------------------
3．THR：Throttle (Channel 3)----------------------------------
4．RUD：Rudder (Channel 4)----------------------------------
9．Power：Input +4.8-6V--------------------------------------
The setting for fail safe:
Receiver connected to the battery (transmitter don't be opened), wait 16 seconds or so, the red
LED flashes, make sure every channel has been putting in the location you need, then open
the transmitter(that is the data receiver output after the out- of- control protection , for example:
throttle is set to 10%, the direction is set to 60%, then when entering the out-of-control protection the
receiver output data is throttle 10%, the direction 60%)
Note:If you need 35MHz to 75MHz,WFLY will supply
FM receiver and FM RF module
5．GYR：Landing Gear/Gyro (Channel 5)--------------------
6．PIT：Pitch (Channel 6)------------------------------ ----------

Trainer function
Two WFT08X transmitters can transfer data between each other or
act as trainer.
Setting Method:
1).Data transfer function: use Trainer/Data transfer cable to
interconnect two WFT08X transmitters.
Select “Send data/Receive data” in SYS setting to transfer the data.
2).Trainer function: use Trainer/Data transfer cable to connect two
WFT08X transmitters.
Insert RF module to the trainer transmitter, student transmitter
doesn’t insert the RF module.
Flip the Trainer switch to enable the student transmitter. By flipping
the trainer switch again, the student’s transmitter signal will be
disabled and the trainer controls the aircraft exclusively.
WFT08X INSTRUCTION
08

FLYING SAFETY WARNINGS
Dangers If you use it without proper operation, it is possible that you
hurt yourself or others seriously or may even cause death.
Warnings If you use it without proper operation, it may cause harm to
you and others as well as it could cause damage to third
party property.
Notices If you use it without proper operation, it may cause you to
hurt slightly or damage things , but it won't hurt you seriously
normally.
Special Symbol Instruction
Forbiddance! Obligation! Warning!
Flying Notice(warning)
Same frequencies can't fly at the same time.
Two radios transmitting on the same frequency will
cause an airplane to crash, even when the modulation
(AM, FM, PCM) is different.
Do not fly at night , during rain or in strong wind, as
you risk damaging your equipment. This device is not
water-proof.
Please check that all servos work properly and
eliminate all problems before operating your model.
(If the radio bounces after turning off the power, there
may be some disturbances, in this case, please
change your channel by exchange crystals)
Checking
Notices Always turn on the transmitter first, then the receiver. When
turning off the system, turn off the receiver first, then the
transmitter.
Notices Children under 14 must be accompanied and instructed by
adults!
To use the product safely, please pay attention to the instructions
as follows.
Please pay special attention to the symbol as follows:
WFT08X INSTRUCTION
09

FEATURES
Computerized transmitter.
132 x 64 FSTN LCD, easy operating keys.
Metal slab shell.
Adjustable antenna base.
Tightness and length of the control stick can be adjusted freely.
Excellent feeling on the stick.
Full digital trim.
Fully exchangeable RF modules.
Trainer function.
3 independent timers, all can be set to count down or increment.
PPM, PCM and PCMS 1024 modulation supported.
Multi-mixing function.
All curves have up to 7 adjustable points.
User-defined switches and knobs.
Model parameters can be exchanged between transmitters.
8-model memories.
The WFT08X transmitter is compatible with FUTABA and JR (PPM)
receivers.
Our Dual conversion receiver(PPM) is compatible with FUTABA and
JR transmitters.
WFT08X INSTRUCTION
10
BATTERY
Specification for the Battery of TX
1. Standared 1.2V AA--5# Ni-MH/Ni-Cd,served with 8S battery holder,
2. Standared 3S-12.6V Lipo,served with Lipo Voltage Regulator.

MENU
Menu key brings you to the function list of the transmitter.
EXIT
Exit key brings you back to the previous menu or exit edit.
+
This key will increase values. If you press long, the increasing
speed will be faster.
-
This key decreases values. If you press long, the decreasing speed
will be faster.
Cursor keys
Move the cursor.
OK
The key in the center of the direction keys is the OK key.
It has following functions:
Enter the function list.
Enter the edit function.
Change parameters back to default by long pressing the key.
Keys
WFT08X INSTRUCTION
11

Allen key
Top thread
stick head
Stick
Put the stick head cover the control rod
on the left and right sides,don't twist down
the stick head to the bottom, and then put
top thread with allen key to adjust the
height you need.
Adjust the height higher: first make the top
thread loose with the allen key, then twist
the stick head up, then, make the top
thread tighten with allen key, Ok, the stick
head was turned up.
Twist the top thread down
from here, the height of the
stick head depends on the
depth of the top thread.
Adjust the height lower: first make the
top thread loose with the allen key, then
twist the stick head down, then, make the
top thread tighten with allen key, Ok, the
stick head was turned down.
steps:
1 Put the stick head on the stick.
2 Put the top thread in the stick head with allen key.
3.Adjust top thread in the stick head with allen key to fix the height of
the stick head.
Adjust the stick head:
12

Bolt 1
Bolt 2
Bolt 3
Bolt 4
13
Change the throttle direction of mode1 or 2
Take the metal chip and
the screw down, and put
it on the similar position
of the right side .
Set up release link and
spring, according your habit
to addjust the the tightness of
screw 2 to adjust the control
feeling.
Take repositor and spring down, and
put it on the left side of the location
of corresponding.then twist bolt 1
down until withstand the adjust nail
in case adjust nail will move away.
Put on the metal chip, according
your habit to adjust the elasticity
of screw 3 and screw 4 to adjust
the damp of throttle control
feeling.

1. Start up Screen
The starting up screen displays the voltage, timer, model, aileron,
throttle, elevator and rudder fine-tuning state.
2. Menu Screen
You will find the “NORMAL SETTING”, “SYS SETTING”, “ADVANCED”.
When turn on the power switch, the LCD displays as follows.
A. NORMAL SETTING
Turning on the transmitter and pressing the menu key, the LCD
displays the follows. 1. MONITOR
2. DUAL RATE & EXPONENTIAL SETTING
3. SERVO REVERSE
4. END POINT
5. SUB TRIM
6. SWASH PARAM SETTING
7. AUXILIARY CHANNELS
8. THROTTLE CURVE SETTING
9. PITCH CURVE SETTING
10. REVOLUTION MIXING
11. TRIM STEP SETTING
12. THROTTLE CUT SETTING
13. FLY MODEL SWITCH
14. THROTTLE HOLDING SETTING
15. FAIL SAFE
16. TIMER
17. ADVANCED
18. LANGUAGE
Voltage Start time
Timer A
Timer B Timer C
Model type
Throttle trim
display
Rudder trim display Aileron trim display
Elevator trim display
Modulation
Editing mode and function introduction
Note: Press EXIT, the screen shows you the model name.
Setting method:
1. Use direction keys change
parameters or use the up/down keys to
browse the functions. Use the left/right
key to switch pages.
2. Press OK to enter submenu.
The submenu function is described in
the next chapter.
3. Press EXIT key to go back from
previous menus. Data is set automatically.
WFT08X INSTRUCTION
Model name
14
HELICOPTER