Wfly WFT02 User manual

V1.3
INSTRUCTION MANUAL
www.wflysz.com
Attention
Please read the instruction before using the product
Please keep this manual
ON
ONONONON

WFT07
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE
Thank you for purchasing the WFLY product
Features
1.The large dot matrix LCD display: multi-language, graphical display. simple design, easy operation.
2.Original 2.4G technology : use of data transfer, greatly improve the handling agility. fully express
the fast Lightning : (Note: is WFLY exclusive technology).
3.Low-voltage design, lower battery consumption, a variety of battery available:such as 4S alkaline batteries ,
4S NiMH(Nickel Metal Hydride),1S lithium-ion battery ,1S lithium polymer battery . Voltage range 3.7V-6V.
4.Super anti-interference: the high spread spectrum (DSSS) + frequency hopping, can boot the 60 sets
at same time without interfere.
5.This RC equipment supports 3 groups of programmable mix.
6.Can store 10 groups of model data .
7.Functions design optimized,operation convenience.
Service
1.The WFLY warranty the quality of science and technology within a year (WFLY technology to bear the
postage, the user must provide a warranty card and proof of purchase,Indispensable).
2.Warranty card and proof of purchase effective by signed and sealed by the seller , and the information
must be completed.
3.Artificially damaged and over one year after the warranty period, the WFLY provide life long science
and technology service,only the users pay return postage, materials fees and maintenance costs.
4.This warranty is limited to China's remote control and accessories sales .
5.Seller does not give warranty card or do not fill out required from the seller to bear all the after-sales service.
ON
ONONONON

1
1
2
3
4
5
6
7
8
9
9
10
11
13
13
13
14
14
15
15
15
16
16
17
17
18
18
19
19
19
20
20
21
21
22
23
23
Ⅰ
WFT07 Remote control device contents
WFT07 Remote control device
WFT07 RC device parts of the name(front)
WFT07 RC device parts of the name( back)
Instructions of the 2.4Ghz receiver
WFT07 code match instructions
Trainer function
Special symbal instructions
WFT07 RC device characteristics
Express of input and buttons
Adjustment of stick head
Replacement throttle hand
Helicopter Functions
System Settings
Input mode and Functions
1.Model parameters
2.Model Settings
3.Coaching / Simulation
4.Control stick settings
5.Control stick Calibration
6.Restore factory settings
7.Tone settings
8.Contrast settings
9.Power supply scheme
10.Version information
Preferences
1.Monitor
2.Dual Rate
3.Servo Reverse
4.End point
5.Sub trim
6.Trim settings
7.Throttle curve settings
8.Pitch curve settings
9.Throttle cut settings
10.Throttle holding settings
11.Timer
12.Swashplate
13.Gyro sens mixing
14.Advanced settings
CONTENTS
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

27
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
29
29
29
30
30
30
30
30
30
31
31
31
32
32
32
Ⅱ
24
24
24
26
CONTENTS
Advanced settings
1.Speeder mixing
2.Programmable mix setting
3.Fail safe
3.Code match
system settings
Airplane Functions
Input mode and functions
1.Model parameters
2.Model settings
3.Coaching / Simulation
4.Control stick settings
5.Control stick calibration
6.Restore factory settings
7.Tone settings
8.Contrast settings
9.Power supply scheme
10.Version information
Preferences
1.Monitor
2.Dual Rate
3.Servo Reverse
4.End point
5.Sub trim
6.Trim settings
7.Flaperon mixing
8.Flap trim
9.Aileron diff control
10.Elev-flap
11.Throttle curve settings
12.Throttle cut settings
13.Throttle holding settings
14.Timer
15.Advanced settings
Advanced Settings
1.Elevator mixing
2.Ele-Aileron mixing
3.V-tail
4.Ail-2
5.Programmable mix setting
6.Fail safe
7.Code match
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

1
1.WFT07 remote control device 2. WFR07S 2.4Ghz receive
3.Simulator switch cable 4.Transmitter 4cell battery case
5.Manual 6.WFLY neck strap
1.WFT07 remote control device 2.WFR07S 2.4Ghz receive 3.Simulator switch cable Manual
4.Transmitter 4cell battery case 6.WFLY neck strap
WFT07 Remote control device contents
WFT07 remote control device diagram
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE
5.Manual/CD-ROM
1 set
1 Root
1 This/zhang
1 Only
1 A
1 Article
ON
ONONONON

ON
ONONONON
K1 K2 K3 K4 V1
2
Antenna(rotatable)
Power light RF light
Buzzer
Elevator trim
Rudder/
elevator stick
Rudder trim
Throttle trim
Aileron/
throttle stick
Power switch
Neckstrap
attachment
Aileron trim
Left
Up
Right
Down
Menu
Exit
Add
Reduce
LCD OK
K1: 2 stalls. Throttle holding and throttle cut K2: 3 stalls. Timer , airplane 5channel and airplane Elev-flap mixing.
K3: 2 stalls. Dual rate, Fight mode (normal,special IDLE) K4: Trainer. 7channels
WFT07 RC device parts of name
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE
WFT07 RC device Positive
(Right hand throttle)

3
WFT07 RC device back
WFT07 RC device parts of name
Trainer/DSC
Handle
Battery cover
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

4
Instruction of 2.4Ghz receiver
Model:WFR07S
Type: 7channel 2.4Ghz receiver,4096 resulotion(in the PCMS 4096 resolution)
(Adaptation WFLY 2.4Ghz series),ORGANIC 2.4G
Voltage :4.8V-6V
Current:30mA
Weight:9.6g
Size: 40.42mm x27.27mm x11.88mm
Frequency: 2.400GHz-2.483GHz
1．AIL：Aileron
2．ELE：Elevator
3．THR：Throttle
4．RUD：Rudder
5．GRY： Landing Gear/Gyro
6．PIT： Pitch
7．Auxiliary channel
(Channel 1)----------
(Channel 2)----------
(Channel 3----------
(Channel 4)----------
(Channel 5)----------
(Channel 6)----------
(Channel 7)----------
WFLY PCMS receiver can compatible with PCMS 4096, PCMS 1024 and PPM modulation
(Adaptive), and have fail safe function.ORGANIC 2.4G
(Note: Any channel can be used as power input)
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

5
WFT07 instructions of the code match
1.Remote control device settings
●unction instruction:
The remote control for the 2.4G spread spectrum,
frequency hopping systems, have high anti-
interference. The remote control has unique
address identification code information, Before
use the remote control,pls match the code with the
2.4Ghz receiver.
●Settings
Into the "Advanced Settings" menu item under the
"Preferences" . Press confirm button to enter the
"code" interface in the "Advanced Settings" . As
above. The specific settings as follows: 1. The
first use the button to select on the code, the code
process needs within a short distance. 2.4G
module system in the closed state is not available,
please refer to “ Once Code Coaching / Simulation”
successfully will return to the menu. Also can press
"exit”button to return.
Warning
When using this function, please ensure that no other remote control operating!
2.Receiver Settings
Remote control device into this interface:
Then going receiver settings: receiver hold "SET" button until the STATUS indicator light flashes slowly, waiting for
the transmitter of the code instructions.
(WFR07S/WFRO9S operating are same)
LED Slow flashing
After the success of the code ,the LED light is off, you can normally using.
Note: The code required in a short distance.
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

6
Trainer Function
Instruction of the Training function
The same two remote control devices WFT07 can do the Trainer function:
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE
1. Using the simulator cable to connect two WFLY equipment.
2. Trainer settings: Press MENU key to boot into the "System Settings" function, enter "
Training / simulation "menu,selected the" trainer mode ", (effect after re-boot ).
3. Student machine setting: Press MENU key of the another radio into the "System Settings" function,
entry "Training / simulation "menu,selected the " Simulator Mode ", (effect after re-boot ).
4. Release Trainer switch K4, this time the student machine does not sending signal, the operation
completed by the trainer.Advance push the trainer switch K4, then operation completed by the
Student machines now.
Settings:

● Large graphic dot matrix LCD display, easy to operate.
● Multi-language
● WFT07 RC device is the multi-function proportion of 7ch remote control .
● The original 2.4G technology , with data transfer , which greatly improve the handling agility
Fully explain the fast as lightning. (Note: The is the WFLY exclusive technology).
● Low-voltage design, lower battery consumption, a variety of battery available:such as 4S alkaline batteries ,
4S NiMH(Nickel Metal Hydride),1S lithium-ion battery ,1S lithium polymer battery . Voltage range 3.7V-6V.
● This RC equipment supports 3 groups of programmable mix.
● Can store 10 groups of model data .
● Joystick of elastic, are free to adjust the hength of the head. The new shape of the head makes a good Feel.
● Digital electronic tuning, 250 steps adjustable.
● Complete the timer function to ensure flight foolproof
● Monitor function can more intuitive operation.
● Training function
● Perfect timing function
● Up to 11 groups of curves, easy to deal with difficult moving actions.
● Multiple mixing control system , adjustable 9 point of the curve .
● A variety of flight patterns,ease flight.
7
Note the special symbol
For the safe use of this product, pls pay attention to
The marks have the following description of symbols.
Dangers: If you use in without a proper operation,it is possible to hurt user seriously injury or may even
cause death .
If you use it without proper operation, it may make the user or others to hurt badly or may even Warnings:
cause death,and it may cause slight hurt or damage to things
Children under 14 must be accompanied by an adult usingWarning:
If you use it without a proper operation, it may cause user to hurt slightly or damage things,butNotices:
it won't hurt you seriourly normally.
Turn on theTransmitter first, then turn on the receiver; after play pls turn off the Receiver first, thenNote:
the Transmitter
Flight Precautions Prohibitions Compulsory Items Warning
※
Do not fly in the evening, rain,or strong wind.
Possible damage to equipment or aircraft accidents.
The Feature of WFT07 Remote control device
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE
ON
ON ON ONON

8
Instruction of the input function
MENU:
After booting, press the menu button to enter the function menu - Preferences. In addition,when
staying in the function interface,press this key will be back
to the menu
EXIT:
Press this key, you can return to the previous menu level, or exit the edit state.
Add/Reduce Key:
Can be used to adjust numerical value. Setting numerical value, keeping pressing + / -, accelerate
the function setting.
Arrow Keys:
Arrow keys are divided into upper and lower, left and right keys, can be used to switch the set up
Or edit the item.
Confirm key:OK key ( this machine confirm key have three kinds of function )
※. With the menu to access the item.
※. To enter the edit mode.
※. Press this button long time, the selected item restore the default value
1.WFLY LOGO
2.2.4G RF circuit directed: shown 2.4G under work, closed without the logo.
3. Aircraft models: helicopter mode, shows the helicopter LOGO, airplane mode, shows the airplane LOGO.
4. Accumulative used time: to display the cumulative duration of the using, can also be reset clear.
5. Battery voltage display.
6. Model data file shows: 1,2,3 ... and so on.
7. Mixing status shows: mixing state (throttle holding, throttle cut, stunt mode) display MIX.
8. Helicopter swashplate shows: If you set a non-normal mode of swashplate, will show CCPM.
9. Trainer function display: Trainer mode will show "T",with flashing.
10. Timer display.
11. Digital electronic tuning: graphics + numerical value dual display, and with tone reminder.
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

ON
ON ON ONON
ON
ON ON ONON
ON
ON ON ONON
ON
ON ON ONON
9
Stick
Adjust the height higher:First make the top
thread loose with the allen key,then twist
the stick head up,then make the top head
tighten with allen key.the stick head was
turned up.
Put the stick head cover the control rod on
the left and right sides,don't twist down the
stick head to the bottom,and then put top
thread with allen key to adjust the height
you needed.
Adjust the height lower:First make the top
thread loose with the allen key,then twist
the stick head down,then make the top
head tighten with allen key.the stick head
was turned down.
Twist the top thread down from
here,the height of the stick head
depends on the depth of the top
thread.
Steps:
1. Put the stick head on the stick.
2. Put the top thread in the stick head with allen key.
3. Addjust top thread in the stick head with allen key to fix the height of the
stick head.
Allen Key
Top thread
Stick Head
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE
Adjustment of stick head

10
Replacement the throttle of mode 1 or 2
Bolt 1.
Bolt 2.
Bolt 3.
Bolt 4.
Set up release link and
springer,according your habit
to adjust the tightness of screw
2 to adjust the control felling.
Put on the matel
chip,according your habit to
adjust the elasticity of screw 3
and screw 4 to adjust the damp
of throttle control felling.
Take the metal chip and
screw down,and put it on
the similar position of the
right side.
Take release link and spring
Down,and put it on the left side of the
location of corresponding,then twist
bolt1 down until withstand the adjust
nail ,in case adjust nsil will move away.
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE
Right-hand man will lose their own free replacement warranty program

11
CCPM
Helicopter Functions
Introduction
This section are mainly introduces the helicopter functions. Please press the MENU button to turn on the
radio, you can enter the "System setting” menu, press Up/Down arrow keys to select" Model Settings ",
press the Enter key to enter the function setting interface, (as above). Please choose the model, re-boot,
then the transmitter can display the functions of the helicopter with the detailed description of each function .
Input mode and function introduction
1.The main interface
When the power turned on, the interface as shown. In this state, the user can view the machine voltage,
time display, model type and aileron, Throttle, elevator, rudder and so on trim state
Voltage WFLY Logo RF modulation Time display
Trainer function
display
Elevator
trim display
Special mixing
Throttle trim
display
Timer
Rudder trim
display
Model parameters
display
Aileron trim
display
Helicopter Functions
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

12
2.Function Menu-There are “System settings”,”Preferences”and “Adcanced settings”in this menu.
A. System Settings
In close state, hold down the MENU key, then turning on the power, you can enter the "System Settings"
menu page, the interface as shown.
In this state, all functions can be set one by one. As follows:
1. Use the arrow keys to select the functions you needed, use up and down keys to select
function items. With the left and right arrow keys to flip.
2. In the functional state ,press OK key to enter sub-menu of the function. The function of specific
configuration, please refer the next chapter.
3. When Settings finished, press EXIT key to return to superior menu,it will automatically store the Settings
value.
B. Parameter Settings
In the boot screen, press the MENU button on the left screen, you can enter the "settings" menu page, the
interface as shown.
In this state, the machine functions can be set one by one . As follows:
1. Use the arrow keys on the screen to select the functions you needed, use up and down arrow keys to
select function items. With the left and right arrow keys to flip.
2. In the functional state ,press OK key to enter sub-menu of the function. The function of specific
configuration, please refer the next chapter.
3.When Settings finished, press EXIT key to return to superior menu,it will automatically store settings
Value.
C. Advanced Settings
Into the "Preferences" menu, use the left and right arrow keys to flip, can see the "Advanced Settings"
function key. Click OK key to enter.
In this state, the machine functions can be set one by one. As follows:
1. Use the arrow keys on the screen to select the functions you needed, use up and down arrow keys to
select function items. With the left and right arrow keys to flip.
2. In the functional state , press OK key to enter sub-menu of the function. The function of specific
configuration, please refer the next chapter.
3.When Settings finished, press EXIT key to return to superior menu, it will automatically store settings
Value.
Helicopter Functions
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

13
System Settings Menu Introduction
1.Model Parameters
●Function
Model parameters function totally have 10
machines for the user to choose, you can select
any of them to setting.
●Settings
Press the MENU button to boot into the “System
Settings" menu, use Up / Down keys to
select the "model parameter settings", and
press the “OK ” key into the function interface,
as shown above.
The steps of setting is as follows:
1. Using the up / down keys to select different
models.
2. Selected the options, press OK key to select .
3. Settings successfully, press EXIT key to exit.
2.Model Settings
Model settings can be used to set to the helicopters, airplane as you needed.
●Function
●Settings
Press the MENU button to boot into the "System
Settings" menu, use Up / Down keys to select
"Model Settings", press the OK key into this
function interface, as shown above.
The steps of setting is as follows:
1. Up / Down keys to select the model.
2. Click OK key to confirm.
3. Settings finished, press EXIT key to return to
superior menu,meanwhile it automatically store
settings value.
3.Coaching / Simulation
◆Normal: normally use the model, RF 2.4GHz
work, do not support the trainer.
◆Trainer mode: use the unit as a trainer, use the
training cable connect the other one as a student
machine. control by the RE2.4machine,to the K4
switch. Not switch K4 is sending to the trainer
machine signal, when push the switch K4 is
sending the student machine signal.
◆Simulator Mode: This mode will turn off RF 2.4G
in order to facilitate learning with other remote
control. Or connect with the computer to simulate
the flight to reduce power consumption to increase
the use of time.
●Function
Note: For security, the above mode switch to take e ffect after reboot.
Helicopter Functions
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

14
图3
●Settings
Press the MENU key to boot into the "System
Settings" menu,use Up / Down arrow keys to
select the "trainer / Simulator", press OK key to
enter the function interface, as shown above. The
steps of setting is as follows:
1, first to use the up / down arrow keys to edit the
selected item.
2. Press OK button to confirm, then press the right
arrow keys to determine. Reboot to take effect.
4.Control Stick Settings
●Function
●Settings
Control stick settings function allows users
to freely setting the higher of the stick according
to personal preferences . As shown. This machine
Totally have four models to be chose .
Press the MENU key to boot into the "System
Settings" menu,use Up / Down keys
to select the "stick settings" and press OK key to
enter this function interface, as shown above
The steps of settings is as follows:
1. First to use the arrow keys to select the edited
item .
2 Use Up / Down key to implement Stick Mode .
3. Set successfully, press EXIT key to exit.
5.Stick Calibration
Joystick calibration function allows users to
change the throttle side according to personal
preferences .
●Function
●Settings
Press the MENU key to boot into the "System
Settings" menu , use Up / Down keys to select
"Stick calibration" and press OK key to enter the
function interface, as Shown above. Specific
settings, follow these steps: 1.First to use the arrow
keys to select the edited item, (aileron calibration as
example ). 2.Put the calibrate joystick placed in the
midpoint of the channel position, options Up / Down -
key implement the control calibration . 3.Selection into
the Figure 3. When the "middle" lights, press OK key
(this time the Point calibrated is OK), into the
stickmaximum (high) calibration. 4.When the "high"
lights, put the stick gently leaned on the right (throttle
/elevator on the top edge, aileron / rudder on the right
edge), press the OK key (in this case the maximum value
has been calibrated), into the stick minimum (low)
calibration. 5.When the "low" lights, put the stick gently
leaned on the left (throttle / elevator on the lowest,
Aileron / rudder on the left edge), press the OK key (while
the stick minimum calibrated OK). 6.At this memont the
bottom of the screen displays "confirmation / reset" and
press to OK key ,all the calibration is completed,
automatically return to the superior menu, use the
arrow key selects to re-enter Calibration
Procedures.
1---ileron
2---evator
3---hrottle
4---Rudder
Helicopter Functions
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

15
6.Restore factory settings
●Function
●Settings
Reset function is to restore the model all the
data back to the initial default settings, so can do
Comprehensive settings of re-work.
Press the MENU key to boot into the "System
Settings" menu, use Up / Down keys to select
"reset ", press Confirm key into the function
interface.As above:
The steps of settings is as follows:
1. First to use the arrow keys to select the
Edited item.
2. With + / - key to implementation the reset.
3. Set successfully, press EXIT key to return.
7.Tone Settings
●Function
●Settings
Tone settings allows users to freely set all the
sounds on or off according to personal
Preference.
Press the MENU key to boot into the "System
Settings" menu, use Up / Down keys to select
"Sound", press the OK key to enter the function
interface, as above.
The steps of settings is as follows:
1. Into the items, press OK key to select the sound
on or off.
2. Automatically saved after confirmation.
8.Contrast Settings
●Function
●Settings
The contrast setting function can
adjust the brightness of the display ,
increase or decrease the contrast value to
change the brightness of the screen.
Press the MENU key to boot into the
"System Settings" menu,use Up / Down
keys to select "Contrast settings" and
press OK key to enter the function
interface ,as above.
The steps of settings is as follows:
1. Using the + / - keys to set the value of
increase / decrease.
2.Keep pressing OK key to restore the default
value.
3. Set successfully, press EXIT key to return.
Helicopter Functions
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE

16
9.Power supply scheme
●Function
●Settings
The machine can use a variety of power options:
such as ordinary alkaline AA batteries 4S, Ni-MH /
Ni-Cd battery 4S, Li-Ion / Li-polymer battery 1S.
Different battery alarm different low-battery voltage
, in order to extend battery life, please select the
corresponding power supply plan.
Press the MENU key to boot into the "System
Settings" menu,use Up / Down arrow keys to
select "Power Information", press OK button to
enter the function interface. As shown above. The
steps of setting is as follows:
1. Use the arrow keys to edit the selected item.
2. Select the power scheme with the + / - key to
implementation.
3. Set successfully, press EXIT key to exit.
10.Power supply scheme
Note:Voltage range 3.7V-6V.
Helicopter Functions
INSTRUCTION MANUAL
WFT07 REMOTE CONTROL DEVICE