Wfly WFT09 User manual

INSTRUCTION MANUAL S02
WFT09 RADIO CONTROL SYSTEM PCM1024
NOTICE
Read the instruction before operation!

WFT09 INSTRUCTION
Thank you for purchacing WFLY product!
WFT09
SERVICE
1. Please come to our retail shops for services. Our retail
shops will service you free in the first half year when you buy
the radio.(apart from people damage)
2. WFLY retail shops will always take your radio service.

CATALOGUE
Contents------------------------------------------------------------------- 01
Transmitter front--------------------------------------------------------- 03
Transmitter back--------------------------------------------------------- 04
Receiver------------------------------------------------------------------ 05
Trainer function----------------------------------------------------------- 06
Flying satety warnings---------------------------------------------------07
Features--------------------------------------------------------------------08
BUTTONS------------------------------------------------------------------09
Editing mode and function introduction-------------------------------10
1. Model selecting--------------------------------------------------------12
2. Model name------------------------------------------------------------13
3. Model setting---------------------------------------------------------- 14
4. ATL--------------------------------------------------------------------- 15
5. Modulation setting----------------------------------------------------16
6. Swash select---------------------------------------------------------- 17
7. Stick setting---------------------------------------------------------- 18
8. Rest setting----------------------------------------------------------- 19
9. Send data------------------------------------------------------------- 20
10. Receive data------------------------------------------------------- 21
11. Contrast setting------------------------------------------------------22
14. Language-------------------------------------------------------------22
Curve setting------------------------------------------------------------ 23
1. Monitor---------------------------------------------------------------- 24
2. Dual rate & Exponential--------------------------------------------- 25
3. Servo reverse--------------------------------------------------------- 26
4. End point---------------------------------------------------------------27
WFT09 INSTRUCTION
I
HELICOPTER
SYS SETTING
NORMAL SETTING

5. Sub trim---------------------------------------------------------------28
6. Swash param setting----------------------------------------------- 29
7. Auxiliary channels setting----------------------------------------- 30
8. Throttle curve setting----------------------------------------------- 31
9. Pitch curve setting-------------------------------------------------- 33
10. Revolution mixing-------------------------------------------------- 35
11. Trim step setting--------------------------------------------------- 36
12. Throttle cut setting------------------------------------------------- 37
13. Fly model switch--------------------------------------------------- 38
14. Throttle holding setting--------------------------------------------39
15. Fail safe--------------------------------------------------------------40
16. TIMER----------------------------------------------------------------41
18. Language------------------------------------------------------------42
(1). GYRO sens setting--------------------------------------------44
(2). Throttle hovering setting------------------------------------- 45
(3). Pitch hovering setting---------------------------------------- 46
(4). HI/LO PIT Setting--------------------------------------------- 47
(5). Trim offset setting--------------------------------------------- 48
(6). DELAY----------------------------------------------------------- 49
(7). Governor mixing----------------------------------------------- 50
(8). Swash and THR mixing--------------------------------------- 51
(9). Cuve setting---------------------------------------------------- 51
(10). PROG.NOR.MIX1-7----------------------------------------- 52
(11). PROG.CUR.MIX1-4----------------------------------------- 53
(12). Throttle needle mixing-------------------------------------- 54
WFT09 INSTRUCTION
II
ADVANCED

WFT09 INSTRUCTION
AIRPLANE
SYS SETTING
MODEL SELECTING-----------------------------------------------------57
MODEL NAME------------------------------------------------------------ 58
MODEL SETTING------------------------------------------------------- 59
ATL------------------------------------------------------------------------- 60
AIL-2----------------------------------------------------------------------- 61
MODULATION SETTING------------------------------------------------ 62
STICK SETTING----------------------------------------------------------63
REST SETTING-----------------------------------------------------------64
SEND DATA----------------------------------------------------------------65
RECEIVE DATA-----------------------------------------------------------66
CONTRAST SETTING---------------------------------------------------67
LANGUAGE----------------------------------------------------------------67
III
NORMAL SETTING
MONITOR------------------------------------------------------------------68
DUAL RATE & EXPONENTIAL SETTING---------------------------- 69
SERVO REVERSE------------------------------------------------------ 70
END POINT--------------------------------------------------------------- 71
SUB TRIM---------------------------------------------------------------- 72
AUXILIARY CHANNELS SETTING------------------------------------ 73
THROTTLE CURVE SETTING------------------------------------------74
TRIM STEP SETTING----------------------------------------------------76
FLAPERON-----------------------------------------------------------------77
FLAP TRIM-----------------------------------------------------------------78
AIL-DIFF--------------------------------------------------------------------79
ELEV-FLAP-----------------------------------------------------------------80

WFT09 INSTRUCTION
IV
THROTTLE CUT SETTING-------------------------------------------- 81
IDLE DOWN-------------------------------------------------------------- 82
FAIL SAFE--------------------------------------------------------------- 83
TIMER--------------------------------------------------------------------- 84
ADVANCED---------------------------------------------------------------85
LANGUAGE-------------------------------------------------------------- 86
CURVE SETTING--------------------------------------------------------87
PROG.NOR.MIX1-7----------------------------------------------------- 88
PROG.CUR.MIX1-4----------------------------------------------------- 89
AIR BRAKE--------------------------------------------------------------- 90
ELEVON------------------------------------------------------------------ 91
AILVATOR----------------------------------------------------------------- 92
V-TAIL---------------------------------------------------------------------- 93
SNAP-ROLL---------------------------------------------------------------94
DELAY----------------------------------------------------------------------95
THROTTLE NEEDLE MIXING------------------------------------------96
GYRO SENS SETTING--------------------------------------------------97
TO THE PILOT
ADVANCED

Contents
Thank you for your attention and support to WFLY radio!
WFLY promises every WFT09 radio control system include the
following contents:
1. WFT09 transmitter
2. WFTRF01 RF module
3. Battery holder for transmitter
4. Battery holder for receiver
5. Charger
6. Neckstrap
7. Trainer cable/Data transfer cable
8. Simulator cable
9. WFR09-P 8 channel dual conversion receiver PPM
10. WFR09-C 9 channel dual conversion receiver PCM
11. Switch harness
12. English instruction manual.
To thank WFLY customers, we provide two times free upgrade
service.
The first version is for helicopter, the following two times
upgrade will add airplane and glider function.
The buyer should take the transportation charge.
WFT09 INSTRUCTION
01

WFT09 Contents
1. Transmitter 2. RF module 3. Transmitter battery
holder
4. Receiver batter
holder
5 Charger 6. Neckstrap
7. Trainer cable/Data
transfer cable
8. Simulator cable 9. PPM receiver
11. Switch harness
WFT09 INSTRUCTION
10. PCM receiver
02

TRANSMITTER
MODEL NO.: WFT09H
MODULATION: FM(PPM) and PCM
OUTPUT POWER: ≤700mW
POWER SUPPLY: 1.2V x 8 (9.6V)
CURRENT DRAIN: 200mA
Band: 35, 36, 40, 41, 72MHz
TRANSMITTER FRONT
WFT09 INSTRUCTION
03
Antenna
Alarm light
RF light
VC Switch F
Trainer switch
Switch D
Switch E
VR
Buzzer
Neckstrap attachment
LCD OK
Down
Right
Up
Left
Aileron trim
Power switch
Throttle trim
Aileron/throttle stick
Decrease
Menu
Exit
Increase
Rudder trim
Elevator trim
Rudder/elevator
stick
VL
Switch B
Switch A
Switch C
VA VB
Power light

TRANSMITTER BACK
Handle
RF module
Battery cover
DSC
Charge hole
WFT09 INSTRUCTION
04

WFR09-P 8 Channels Dual Conversion Receiver (PPM)
1．AIL：Aileron (Channel 1)------------------------
2．ELE：Elevator (Channel 2)----------------------
3．THR：Throttle (Channel 3)-----------------------
4．RUD：Rudder (Channel 4)-----------------------
5．GYR：Landing Gear/Gyro (Channel 5)---------
6．PIT：Pitch (Channel 6)------------------------------ -
7．AUX1：Auxiliary channel 1 (Channel 7)---------
8．AUX2：Auxiliary channel 2 (Channel 8)---------
9．Power：Input +5V-----------------------------
(There are 9 rows needles, 3 needles in each row,
from the top needle to the bottom, the 3 needles are PCM/PPM pulse, +5V and Ground.)
72MHz, pull up the switch to A, the receiver is compatible with WFLY
and FUTABA series transmitters.
Pull down the switch to B, the receiver is compatible with JR series
transmiters.
35MHz and 40MHz are compatible with WFLY, FUTABA and JR
transmitters.
The receiver is only used for WFT09 transmitter.
Make sure you set FAIL SAFE when using PCM.
WFR09-C 9 Channels Dual Conversion Receiver (PCM)
1．AIL：Aileron (Channel 1)-------------------------
2．ELE：Elevator (Channel 2)----------------------
3．THR：Throttle (Channel 3)------------------------
4．RUD：Rudder (Channel 4)------------------------
5．GYR：Landing Gear/Gyro (Channel 5)----------
6．PIT：Pitch (Channel 6)------------------------------
7．AUX1：Auxiliary channel 1 (Channel 7)----------
8．AUX2：Auxiliary channel 2 (Channel 8)-----------
9．Power：Input +5V--------------------------------------
(There are 9 rows needles, 3 needles in each row,
from the top needle to the bottom, the 3 needles are PCM/PPM pulse, +5V and Ground.)
Indicator light
1. Usually, it’s Bit Error Rate indicator. The light becomes brighter
when the rate is bigger.
2. The light glitters once per second when the voltage is low.
3. The light glitters once per 0.4 second when receiving data(Fail safe)
or big Bit Error Rate occurs.
WFT09 INSTRUCTION
RECEIVER
MODEL NO.: WFR09
TYPE: 9 CH PCM/PPM, Dual conversion
POWER SUPPLY: 1.2V x 4 (4.8V)
CURRENT DRAIN: 9.5mA
WEIGHT: 19 g
DIMENSION: 44.88mm x27.90mm x16.39mm
BAND: 35, 36, 40, 41, 72MHz
05

Trainer function
Two WFT09 transmitters can transfer data and realize trainer function.
Setting Method:
1).Data transfer function: use Trainer cable/Data transfer cable to
connect two WFT09 transmitter.
Select “Send data/receive data” in SYS setting to transfer the data.
2).Trainer function: use Trainer cable/Data transfer cable to connect
two WFT09 transmitters.
Insert RF module to the trainer transmitter, student transmitter
doesn’t insert the RF module.
Pull Trainer switch for student transmitter operating. If any wrong
operation occurs, trainer pushes trainer switch and student
transmitter stops sending signal, trainer transmitter controls the
aircraft.
WFT09 INSTRUCTION
06

FLYING SAFETY WARNINGS
Dangers：If you use it without proper operation, it is possible to hurt
you seriously or may even cause death.
Warnings：If you use it without proper operation, it may make you or
others to hurt badly or may even cause death, and it may
cause slight hurt or damage to things.
Notices：If you use it without proper operation, it may cause you to
hurt slightly or damage things , but it won't hurt you seriously
normally.
Special Symbol Instruction
Forbiddance! Obligation! Warning!
Flying Notice(warning)
Same frequencies can't fly at the same time.
Same frequencies used synchronously will cause
the plane to crash or to damage even the modulation
ways of AM, FM, PCM are not the same, when the
frequencies are identical, it will cause the plane to
prang or to damage.
Do not fly at night , in rain day ,or in strong wind,
which will damage the device or plane. This device
is not water-proof.
The antenna should be fully pulled out when using it
or the signal will be weakened and the control range
will reduce, which may cause the crash.
Please check every servo works properly and eliminate
any disturbing signals before you play it. (If the radio
bounces after turning off the power, there may be some
disturbances, in this case, please change your channel
by exchange crystals )
Checking
Notices: Turn on the transmitter first, then the receiver. When turning
off the system, turn off the receiver first, then the transmitter.
Notices：Children under 14 must be accompanied and instructed by
adults!
To use the product safely, please pay attention to the instruction
as follows.
Please pay special attention to the symbol as follows:
WFT09 INSTRUCTION
07

FEATURES
Computerized transmitter.
132 x 64 FSTN LCD, easy operating buttons.
Metal slab shell.
Adjustable antenna basement.
Tightness and length of the control stick can be adjusted freely.
Excellent touch of the stick movement.
Full digital trim.
Independent RF module for easy band exchange.
Trainer function.
3 independence timer, all can be set to count down or increment.
PCM and PPM modulation supported.
Multi mixing function.
All curves have eleven fully position adjustable point.
User defined switch and knob.
Model parameter can be exchange between transmitter..
10-model memory.
WFT09 transmitter is compatible with FUTABA and JR (PPM) receiver.
Dual conversion receiver(PPM) is compatible with FUTABA and JR
transmitter.
WFT09 INSTRUCTION
08

MENU
Menu button brings you to the function list of the transmitter.
EXIT
Exit button is to back the previous menu or exit edit.
+
This button is to increase the value. If you press it for a while,
the increasing speed will be faster.
-
This button is to decrease the value. If you press it for a while,
the decreasing speed will be faster.
Cursor buttons
Move the cursor.
OK
The button in the middle of the direction buttons is the OK button.
The function is as follows:
To enter the function list.
To enter the edit function.
To back the default for long time press.
Buttons
WFT09 INSTRUCTION
09

HELICOPTER
Press Menu and turn on the transmitter to enter SYS SETTING.
Select MODEL SETTING, press OK button to select the model
type.
Restart the transmitter after setting.
WFT09 INSTRUCTION
HELICOPTER

1. Opening Screen
The opening screen displays the voltage, timer, model, aileron,
throttle, elevator and rudder state.
2. Menu Screen
There are “System setting”, “SYS setting”, “More setting”.
Turn on the power switch, the LCD displays as follows.
A. System setting
Turn on the transmitter, press the menu button, the LCD displays
as follows. 1. MONITOR
2. DUAL RATE & EXPONENTIAL SETTING
3. SERVO REVERSE
4. END POINT
5. SUB TRIM
6. SWASH PARAM SETTING
7. AUXILIARY CHANNELS
8. THROTTLE CURVE SETTING
9. PITCH CURVE SETTING
10. REVOLUTION MIXING
11. TRIM STEP SETTING
12. THROTTLE CUT SETTING
13. FLY MODEL SWITCH
14. THROTTLE HOLDING SETTING
15. FAIL SAFE
16. TIMER
17. MORE SETTING
18. LANGUAGE
Voltage Start time
Timer A
Timer B Timer C
Model type
Throttle trim
display
Rudder trim display Aileron trim display
Elevator trim display
Idle
Editing mode and function introduction
Note: Press EXIT you can see the model name.
Setting method:
1. Use direction button to select the
editing part,use up/down buttons to
select function item. Left/right
direction button to turn page.
2. Press OK button to enter submenu.
The submenu function is in the next
chapter.
3. Press EXIT button to back previous
menu and the data is set automatically.
WFT09 INSTRUCTION
Model name
10
HELICOPTER

B. SYS SETTING
Press Menu and turn on the power switch, the LCD displays as
follows.
1. MODEL SELECTING
2. MODEL NAME
3. MODEL SETTING
4. ATL
5. MODULATION SETTING
6. SWASH SELECT
7. STICK SETTING
8. REST SETTING
9. SEND DATA
10. RECEIVE DATA
11. CONTRAST SETTING
12. ENGINEER MODEL
13. ABOUT
14. LANGUAGE
Setting method:
1. Use direction button to select the
editing part,use up/down buttons to
select function item. Left/right direction
button to turn page.
2. Press OK button to enter submenu.
The submenu function is in the next
chapter.
3. Press EXIT button to back previous
menu and the data is set automatically.
C. ADVANCED
1. Enter “NORMAL SETTING”, use right direction button to turn page,
select “ADVANCED”.
Press OK button to enter.
Setting method:
1. Use direction button to select the editing part,
use up/down buttons to select function item.
Left/right direction button to turn page.
2. Press OK button to enter submenu. The submenu
function is in the next chapter.
3. Press EXIT button to back previous menu and the
data is set automatically.
WFT09 INSTRUCTION
11
HELICOPTER

1.Model selectting
There are 10 helicopter models. You can select any one to set.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “Model selecting”, OK button is
to enter editing.
Steps:
1. Use up/down direction button to select the model.
2. Press OK button to select.
3. Press EXIT after setting.
SYS SETTING
WFT09 INSTRUCTION
12
HELICOPTER

2. Model name
This function is to make new names by users.
Setting Method:
Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “Model name”, OK button is to
enter editing.
Steps:
1. You can edit the underlined letter.
2. Press OK button to choose the word you like.
3. Press EXIT after setting.
WFT09 INSTRUCTION
13
HELICOPTER