Whalen Linwood MNFP60LW26IO User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2020-05-23 Rev. 0001-A
Linwood 60in Fireplace Console
Model # MNFP60LW26IO
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenfurniture.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /
OR

2
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and
non-abrasive surface. You will need the parts identified on page 3 and 4 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE
WIPED OFF WITH A DAMP CLOTH.
Insert dowel at least half way by tapping lightly with a rubber mallet (not included), IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the pre-drilled small holes on the panel. Connect both panels together; making
sure the Cam Bolt goes into the pre-drilled hole at the end of the panel with the Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole in the panel. Make sure the arrow on the Cam Lock is
pointed towards the Cam Bolt.
3. Once the Cam Bolt is connected inside the Cam Lock, take a Phillips screwdriver (not included) and
tighten the Cam Lock clockwise.
4. Plug the Cam Lock Cover into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
How to adjust the European adjustable hinges on doors?
Shipping may cause doors to become out of alignment. If you find that the doors need to be adjusted
slightly, turn the appropriate screw as illustrated below.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
12
3
GLUE
XXFINAL
1 2 43
1234

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Fixed Shelf (Qty. 1)
C- Base (Qty. 1) D- Side Panel (Qty. 2)
E- Left Partition Panel (Qty. 1) F- Right Partition Panel (Qty. 1) G- Wood Door Panel (Qty. 2)
H- Middle Stile (Qty. 2) I- Firebox Support (Qty. 1) J- Adjustable Shelf (Qty. 4)
K- Door (Qty. 2) L- Side Back Panel (Qty. 2) M- Middle Back Panel (Qty. 1)
N- Middle Crossbar (Qty. 1) Fireplace Insert (Qty. 1) Remote Control with Battery (Qty. 1)

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 20+1 extra) (Qty. 20+1 extra) (Qty. 22+1 extra)
(4) M3.5x15mmWasherHeadScrew (5) M3.5x15mmPanHeadScrew (6) M4x 25mmScrew
(Qty. 41+2 extra) Qty. 8+1 extra) (Qty. 6+1 extra)
(7) M8 x 20 mm Wood Dowel (8) L-shaped Metal Bracket (9) Handle with Metal Plate
(Qty. 4+1 extra) (Qty. 2) (Qty. 2)
(10) 5/32’’ x 22 mm Bolt (11) Shelf Support (12) Rubber Bumper
(Qty. 4+1 extra) (Qty. 16+1 extra) (Qty. 4+1 extra)
(13) Cam Lock Cover (14) M3.5x12mmScrew (15) M4x 32mmScrew
(Qty. 16+1 extra) (Qty. 4+1 extra) (Qty. 3+1 extra)
(16) Mending Plate(Qty. 2) Glue (Qty. 1) Touch-up Pen (Qty. 1)
TippingRestraintHardwareKit(Qty.2)
(Included in plastic bag)
Tools required (not included): Phillips screwdriver, stud finder, pencil, tape measure, power drill and 1/8 in
drill bit.

5
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A), Base (C) and
Partition Panels (E and F) with a Phillips screwdriver.
NOTE: Screw-in cam bolts must be screwed down flush.
3. Insert twenty 30 mm Wood Dowels (3) into the inner holes on the Fixed Shelf (B), Side Panels (D) and
Partition Panels (E and F). Make sure that you use a small amount of glue with both ends of all dowels.
NOTE: It is very important to use a small amount of glue on both ends of dowels.
2
C
A
F
E
3
3
B
3
3
33
333
3
3
3
3
3
EF
DD
3
3
3
3
3
3

6
Assembly Instructions
4. Glue two 20 mm Wood Dowels (7) into the inner holes on each Middle Stile (H).
5. Attach the Middle Stiles (H) to the Partition Panels (E and F) respectively with three 25 mm Screws (6)
per stile.
6. Glue two 30 mm Wood Dowels (3) into the inner holes on the Middle Crossbar (N).
7. Attach the Middle Crossbar (N) to the Fixed Shelf (B) with three 32 mm Screws (15).
E
6
H
H
H
F
6
H
7
7
7
7
3
3
B
N
NB
N
15

7
Assembly Instructions
8. Attach the Fixed Shelf (B) between the Partition Panels (E and F) by engaging four Cam Locks (1)
(Refer to page 2 on Cam Lock system operation supplement).
9. Using the wood dowels as a guide, firmly press the assembled Partition Panels (E and F) to the Base (C)
and fasten them with four Cam Locks (1).
1
E/F
B
E
F
B
1
C
E/F
E
F
C

8
Assembly Instructions
10. Align the large holes on one Side Panel (D) with the inserted wood dowels on the Base (C). Firmly
press them together and fasten it in place by engaging two Cam Locks (1).
11. Repeat the same procedure to attach the other Side Panel (D) at the other end.
12. Place the Top Panel (A) onto the inserted wood dowels properly and fasten it in place by engaging
eight Cam Locks (1).
1
CD
C
D
D
1
AD/E/F
D
D
A
E
F

9
Assembly Instructions
13. Ask for assistance to flip the unit around at its front edge as shown.
14. With the pilot holes as a guide, fasten the Middle Crossbar (N) to the Middle Stiles (H) by attaching
two Mending Plates (16) at the joints, using two 12mm Screws (14) per plate.
15. Pick up the Middle Back Panel (M) and align the pre-drilled holes against the upper long edge with the
pilot holes on the back rail of Top Panel (A). Attach the Middle Back Panel (M) in place with provided
15mm Washer Head Screws (4).
16. Using the pilot holes as a guide, align and attach the Side Back Panels (L) to the mantel frame with the
provided 15mm Washer Head Screws (4).
NOTE: We recommend attaching back panel with washer head screws at the corners first.
NH
H
14
16
NH
L
M
L
4
L/M

10
Assembly Instructions
17. Ask for assistance to lift the assembly unit upright and position it near the final installation location.
18. Pick up one Door (K) and attach the extended hinge arms to the hinge bases installed on the one Side
Panel (D). Please follow the steps below to combine the door hinges together.
a). Extend both hinge arms of the Door (K) to open position.
b). Locate the lugs on the mounting plates pre-attached on the Side Panel (D) into the “J” hooks
beneath the hinge arms.
c) Press lightly on the end of both hinge arms to engage the catch.
d) To remove the hinge arms from the mounting plates, press gently in the release lever on the back of
hinge arms.
19. Repeat the same procedure to install the other Door (K) to the other Side Panel (D).
20. Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the
screws for a good fit. Refer to the hinge sticker on door for adjustment.
21. Open the doors and attach one Handle with Metal Plate (9) to the front side of each Door (K) with two
22 mm Bolts (10).
D
D
D
K
K
K
K
K
K
10
9