WhatsGPS R11 User manual

Model：R11
User Manual
GPS Tracker

Thank you very much for using the R11 vehicle terminal
(mobile user terminal) product. Please read this
manual carefully before use. Please pay attention to all
the cautions and warnings mentioned in the manual.
Please keep this manual properly for reference.
This manual, as well as the description of the software,
can be used or copied directly after receiving the
license, only in accordance with such authority.
The content of this manual is to provide information for
use, subject to change without notice, and should not
be regarded as a commitment by SEEWORLD.
SEEWORLD assumes any liability or any deviation of
legal liability may appear in this book.
SEEWORLD Company reserves the right to make
changes to specifications at any time without notice.
SEEWORLD Corporation believes that this manual is
accurate and reliable. However, SEEWORLD
Corporation is not responsible for its use, or
infringement of patents or the rights of other third
parties caused by its use. Without a license, any patents
or patent rights will belong to SEEWORLD.
Statement

Content
1. Product Description ----------------------------------- 3
2. Product Features --------------------------------------- 3
3. Specifications ------------------------------------------- 4
4. Appearance ---------------------------------------------- 5
5. Installation Instrusctions ----------------------------- 6
6. Setting Command Instructions----------------------- 9
7. Installation diagram-----------------------------------11
8. Troubleshooting---------------------------------------11

1. Product Description ----------------------------------- 3
2. Product Features --------------------------------------- 3
3. Specifications ------------------------------------------- 4
4. Appearance ---------------------------------------------- 5
5. Installation Instrusctions ----------------------------- 6
6. Setting Command Instructions----------------------- 9
7. Installation diagram-----------------------------------11
8. Troubleshooting---------------------------------------11
The R11 is a multifunctional GPS tracker with a wide
range of applications. Adopts MTK6261 chip and
supports GPS, COMPASS, GLONASS satellite
systems. In addition to supporting satellite
positioning, the equipment also supports
single-base and multi-base station positioning. Rich
extended functions, please refer to the following
descriptions about extended functions. Integrating
a self-developed hardware monitoring circuit
enables the equipment to work reliably and stably
for a long time, and can automatically recover when
an abnormality occurs.
● GSM quad-band, built-in GSM/GPS antenna;
● Support all global navigation satellite systems
GPS, COMPASS, GLONASS, Beidou that have been
deployed and will be in operation
● Support global multi-base station and satellite
positioning mode;
● Voltage input 9-90V;
2. Product function
1.Product Description

● Built-in high-power surge protection circuit;
● Adopt high temperature resistant, safe and
explosion-proof rechargeable lithium cobalt oxide
battery;
● Built-in high-power surge protection circuit;
● Built-in hardware monitoring circuit, automatic
recovery of abnormal state;
● Support remote oil circuit control;
● Support ACC detection and alarm;
● Built-in battery switching circuit, support power
failure alarm;
● Built-in vibration sensor, support vibration
alarm;
● Support remote upgrade;
● IP65 waterproof design;
2. Main Function

3. Specification
Items Specifications Remark
Working Voltage DC9V-90V
Working Current
Dimension
Positioning mode
25ma @12V
(Quiescent current 10mA) Not charging
L80mm *W28mm*H14mm
GPS+LBS+WIFI(Optional)
Positioning error <10 Meters
communication
network GPRS
Communication
way TCP
GSM frequency 850/900/1800/1900MHz
Temperature
range -25℃~ +75℃
Backup battery
working time 0.5h
Warranty period 1 Year
Storage
temperature range -40℃ ~ +85℃

By checking the status indicator, you can
understand the working condition of the device.
The status of the indicator is described as follows:
Thank you very much for using the R11 vehicle terminal
(mobile user terminal) product. Please read this
manual carefully before use. Please pay attention to all
the cautions and warnings mentioned in the manual.
Please keep this manual properly for reference.
This manual, as well as the description of the software,
can be used or copied directly after receiving the
license, only in accordance with such authority.
The content of this manual is to provide information for
use, subject to change without notice, and should not
be regarded as a commitment by SEEWORLD.
SEEWORLD assumes any liability or any deviation of
legal liability may appear in this book.
SEEWORLD Company reserves the right to make
changes to specifications at any time without notice.
SEEWORLD Corporation believes that this manual is
accurate and reliable. However, SEEWORLD
Corporation is not responsible for its use, or
infringement of patents or the rights of other third
parties caused by its use. Without a license, any patents
or patent rights will belong to SEEWORLD.
4. Appearance

5.1. Wiring
LED
Color LED Status Description
Red
Fast flash
GPRS online
GPS receive signal is normal
Slow flash
light
GSM starting
No GSM signal/card/still sleep
Drak
Blue
GPS signal searching
Fast flash
GPS position
Light
GPS sleep/not working
Dark
5.Installation instructions
Line No. Specification Color Instruction
MOTOR Yellow
ACC
V-
8
9
ACC
White
Black
Fuel control wire
ACC
12V/24V
Connect to Powe
of 12V/24V
Red11
10

Precautions for Relay Wiring
Pump relay wiring: the oil connectors at both ends
are thin white wire (85) and thin yellow wire (86).
The thin white wire (85) is connected to the vehicle's
positive power supply (+12V). The thin yellow wire is
connected to the device relay control wire.
Cut off the positive connection wire of the pump;
then connect in series to the relay normally closed
contact (green thick line 87a), and the other end to
the relay COM contact (green thick line 30).

● GSM quad-band, built-in GSM/GPS antenna;
● Support all global navigation satellite systems
GPS, COMPASS, GLONASS, Beidou that have been
deployed and will be in operation
● Support global multi-base station and satellite
positioning mode;
● Voltage input 9-90V;
6.Description of command
Instructions
6.1.Oneline Setting Command List
1
SERVER,1,<domain>,<port>#
E.g.:SERVER,1,gps.
whatsgps.com,6801,0#
Please move to the
network service
provider service area
3TIMER,T#
T:The range of T is
5-900 second
The default reporting
interval is T second
after setting
2APN,<use_apn>#
E.g.:APN,internet# Set APN
6.2. Query command
1PARAM# Query device parameters
2STATUS# Set APN
3WHERE# Query latitude and longitude
4RESET# evice restart

● Built-in high-power surge protection circuit;
● Adopt high temperature resistant, safe and
explosion-proof rechargeable lithium cobalt oxide
battery;
● Built-in high-power surge protection circuit;
● Built-in hardware monitoring circuit, automatic
recovery of abnormal state;
● Support remote oil circuit control;
● Support ACC detection and alarm;
● Built-in battery switching circuit, support power
failure alarm;
● Built-in vibration sensor, support vibration
alarm;
● Support remote upgrade;
● IP65 waterproof design;
6. Installation Instruction
6.3.Alarm mode setting and description
1Vibration
alarm
SENALM,A
,M#
A=ON/OFF, turn on or turn
off the alarm, the default
is off
M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
2: GPRS+SMS+PHONE
2Power off
alarm
POWERAL
M,A,M#
A=ON/OFF, turn on or turn
off the alarm, the default is
off
M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
2: GPRS+SMS+PHONE
3ACC alarm ACCALM,A
,B,M#
A=ON/OFF, turn on or turn
off the alarm, the default
is off
B=1/2/3, 1 is ACC ON
alarm, 2 is ACC OFF alarm,
3 is ACC ON + ACC OFF
alarm
M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
3: GPRS+SMS+PHONE
4Displacemen
t alarm MOVING,A
,R,M#
A=ON/OFF, turn on or turn
off the alarm, the default is
off
R=100-1000, moving
distance, unit: meter,
default is 300
M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
3: GPRS+SMS+PHONE

5Over speed
alarm
SPEED,A,
B,M#
A=ON/OFF, turn on or turn
off the alarm, the default is
off
B=1-255 (Km/h), the
overspeed threshold, the
default is 100 (Km/h)
M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
3: GPRS+SMS+PHONE
6.4.SOS and Center Number Setting
1SOS setting SOS,A,phon
e1,phone2,
phone3#
The SOS number can be
set to 1-3 numbers.
Note: When the number
already exists, using this
command will clear the
previously set number and
replace it with a new SOS
number
2Center
number
setting
CENTER,
A,phone
number#
Add center number, only
center number and SOS
number can be set
6.5.Remote oil cut
1Remote oil
cut
RELAY,1#
When the car speed
reaches below 20KM/H, the
command will be executed
successfully
2Remote oil
restore RELAY,0# Restore the oil circuit

7.Installation diagram

8.Trouble shooting
When operating the terminal, if you feel that the
equipment is abnormal, please refer to the
following problems and solutions. If the problem
still cannot be solved, please contact the seller or
service provider.
Common
Problem Reason Solution
Bad Signal
Unable to
connect to
the network
Dirt on the metal
surface of the SIM
card
Wipe with a clean cloth
Invalid SIM card Contact your internet
service provider
Please move to a place
with strong signal and
try again
Out of GSM service
area
When using the
terminal in areas
with poor signal
reception, such as
near high-rise
buildings or
basements, radio
waves cannot be
effectively
transmitted
SIM card is not
installed
Check the SIM card
Use the terminal in
a location with
good signal

Precautions for Relay Wiring
Pump relay wiring: the oil connectors at both ends
are thin white wire (85) and thin yellow wire (86).
The thin white wire (85) is connected to the vehicle's
positive power supply (+12V). The thin yellow wire is
connected to the device relay control wire.
Cut off the positive connection wire of the pump;
then connect in series to the relay normally closed
contact (green thick line 87a), and the other end to
the relay COM contact (green thick line 30).
Common
Problem Reason Solution
Please confirm
whether the device
is switched on
Turn on the device
battery switch
SIM卡Please install
the SIM card
Unable to
connect to
the network
Poor contact Check if the plug is
connected
Switch off Please check if the
SIM is installed
Weak signal
Please move to a
place with strong
signal and try again

Warranty card
Maintenance record
Maintenance shop
Fault description
Maintenance situation
IMEI number
Maintenance
person
Sending date
Maintenance record
Maintenance shop
Fault description
Maintenance situation
IMEI number
Maintenance
person
Sending date

FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions (1)this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.