Whitewood Furniture LACASA ROUND END TABLE OT-621RE User manual

ITEM NO.: OT-621RE
ISSUED SEP 20, 2022
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: LACASA ROUND END TABLE
: OT-621RE

ITEM NO.: OT-621RE
ISSUED SEP 20, 2022
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: OT-621RE
ISSUED SEP 20, 2022
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Mounting
Plate
2
C
Base(small)
2
D
Base(large)
2
E
Leg
4
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Short Bolt
(M6 x 30mm)
16
2
Medium Bolt
(M6 x 45mm)
4
3
Medium Screw
(M4 x 35mm)
2
4
Lock Washer
(6.5 x 11mm)
20
5
Flat Washer
(6.5 x 13mm)
20
6
Allen Key
(M4 x 30mm x 110mm)
1

ITEM NO.: OT-621RE
ISSUED SEP 20, 2022
Printed in Vietnam
- 4 -
STEP 1
Attach legs (E) to bases (C) with bolts (1), and washers (4) and (5) as shown below. Tighten with Allen
key (6).
Put two bases (C) together as shown below.
STEP 2
Attach mounting plates (B) to legs (E) with bolts (1), and washers (4) and (5) as shown below. Tighten
with Allen key (6).

ITEM NO.: OT-621RE
ISSUED SEP 20, 2022
Printed in Vietnam
- 5 -
STEP 3
Attach bases (D) to bases (C) with bolts (2), and washes (4) and (5) as shown below. Tighten with
Allen key (6).
Attach bases (D) to bases (C) with screws (3) as shown below. Tighten with a screwdriver.
STEP 4
Attach mounting plates (B) to top (A) with bolts (1), and washes (4) and (5) as show below. Tighten
with Allen key (6).

ITEM NO.: OT-621RE
ISSUED SEP 20, 2022
Printed in Vietnam
- 6 -
STEP 5
Adjust the levelers to the appropriate height to level the table.