Whitewood Furniture ATHENA T-6840X User manual

ITEM NO.: T-6840X
ISSUED AUG 07, 2018
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: 40X66X84 ATHENA TABLE
: T-6840X

ITEM NO.: T-6840X
ISSUED AUG 07, 2018
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your table. Protect the surface of the table with cloth if you are using any product
with rubber feet or base.

ITEM NO.: T-6840X
ISSUED AUG 07, 2018
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Table Top
1
B
Leg Frame
2
C
Support
Stretcher
2
D
Extension
Leaf
1
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Large Bolt
(M8 x 40mm)
8
5
Small Spring Washer
(6.5 x 11mm)
4
2
Small Bolt
(M6 x 40mm)
4
6
Small Flat washer
(ɸ6.5 x 13mm)
4
3
Large Spring
Washer
(8.5 x 13mm)
8
7
Allen key
(M4 x 30mm x 110mm)
1
4
Large Flat Washer
(ɸ8.5 x 19mm)
8

ITEM NO.: T-6840X
ISSUED AUG 07, 2018
Printed in Vietnam
- 4 -
STEP 1
Use the Allen key (7) to loosen bolts and washers, and then remove the mounting plate from bottom
of the table top (A) as shown below.
STEP 2
Attach the mounting plate to support stretchers (C) with bolts (2), and washers (5) and (6) as shown
below. Tighten with the Allen key (7).
REMOVE
A
C

ITEM NO.: T-6840X
ISSUED AUG 07, 2018
Printed in Vietnam
- 5 -
STEP 3
Attach support stretchers (C) to leg frames (B) with bolts (2), and washers (5) and (6) as shown below.
Tighten with Allen key (7).
Attach the mounting plate to bottom of the top (A) with bolts and washers (from Step 1) as shown
below. Tighten with Allen key (7).
Attach leg frames (B) to top (A) with bolts (1), and washers (3) and (4) as shown below. Tighten with
Allen key (7).
7
2
5
A
C

ITEM NO.: T-6840X
ISSUED AUG 07, 2018
Printed in Vietnam
- 6 -
STEP 4
Unlock the table top on both sides from underneath the top. Pull the 2 parts of the table top apart.
Place the leaf (D) in the center of the open table top.
STEP 5
Push the table top closed. Lock the mechanism underneath two sides of the table top as shown below.
B
A
RELOCK SPRING CLIP

ITEM NO.: T-6840X
ISSUED AUG 07, 2018
Printed in Vietnam
- 7 -
STEP 6
Unlock the table top on both sides from underneath the top. Pull the 2 parts of the table top apart.
Remove the leaf (D) and put it on the mounting plate underneath the table top as shown below.
STEP 7
Push the table top closed. Lock the mechanism underneath two sides of the table top as shown below.
UNLOCK SPRING CLIP
A
D
RELOCK SPRING CLIP