Whitewood Furniture STURBRIDGE TV-51 User manual

ITEM NO.: TV-51
REVISED FEB 15, 2019
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: STURBRIDGE TV CENTER RTA
: TV-51

ITEM NO.: TV-51
REVISED FEB 15, 2019
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-51
REVISED FEB 15, 2019
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
F
Vertical Panel
(L-R)
2
B
Center Panel
1
G
Center Shelf
1
C
Door (L-R)
2
H
Side Shelf
(L-R)
2
D
Side Panel
(L -R)
2
I
Back Panel
1
E
Bottom Panel
1

ITEM NO.: TV-51
REVISED FEB 15, 2019
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Long Bolt
(M6 x 35mm)
20
8
Short Pan head screw
(M3.5 x 15mm)
9
2
Spring Washer
(6.5 x 11mm)
16
9
Short Screw
(M3.5 x 15mm)
16
3
Flat Washer
(6.5 x 19mm)
16
10
Magnet
2
4
Door pin
(5.2/13 x 1.2mm)
(7 x 10mm)
4
11
Allen key
(M4 x 30mm x 110mm)
1
5
Long Pan head screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
2
12
Short Pan head screw
(M3 x 15mm)
4
6
Wooden Knob
(38 x 30mm)
2
13
Warning Label
2
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
2
14
Steel band
2
7
Bracket
12
15
Long Screw
(M4 x 35mm)
2

ITEM NO.: TV-51
REVISED FEB 15, 2019
Printed in Vietnam
- 5 -
STEP 1
Attach vertical panels (F) to center panel (B) with bolts (1), and washers (2) and (3) as shown below.
Tighten with Allen key (11).
Attach doors (C) to center panel (B) and bottom panel (E) with door pins (4).
Attach vertical panels (F) to bottom panel (E) with bolts (1) as shown below. Tighten with Allen key (11).
Attach magnets (10) to vertical panels (F) with pan head screws (12) as shown below. Tighten with a
screwdriver.

ITEM NO.: TV-51
REVISED FEB 15, 2019
Printed in Vietnam
- 6 -
STEP 2
Attach side panels (D) to top (A), center panel (B) and bottom panel (E) with bolts (1), and washers
(2) and (3) as shown below. Tighten with Allen key (11).
STEP 3
Slide back panel (I) into grooves of the side panels (D) and top (A) as shown below. Then attach
back panel (I) to the unit with pan head screws (8) as shown below. Tighten with a screwdriver.

ITEM NO.: TV-51
REVISED FEB 15, 2019
Printed in Vietnam
- 7 -
STEP 4
Insert brackets (7) to the unit as shown below. Place shelves (G) and (H) on the brackets and attach
with screws (9). Tighten with a screwdriver.
Attach knobs (6) to doors (C) with pan head screws (5) as shown below. Tighten with a screwdriver.
Attach steel bands (14) to the unit with short screws (9) and attach the steel band to the wall with long
screws (15) as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.
Stick warning labels (13) on the back side of doors before use.