Whitewood Furniture MILANO T-4096 T Series User manual

ITEM
NO
:
T
-
4096XXT
AND
T
-
4096XXB
REVISED NOV 20, 2012
Printed in Vietnam
THE HARDWARE REQUIRED TO ATTACH THE PEDESTAL IS PACKED WITH THE PEDESTAL. - 1 -
Description
Item No
:
MILANO
TA LE TOP & MILANO
TA LE
ASE
:T-4096XXT AND T-4096XX
ASSEMBLY INSTRUCTIONS

ITEM
NO
:
T
-
4096XXT
AND
T
-
4096XXB
REVISED NOV 20, 2012
Printed in Vietnam
THE HARDWARE REQUIRED TO ATTACH THE PEDESTAL IS PACKED WITH THE PEDESTAL. - 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
- Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
- Remove all wrapping material, including staples & packing straps before you start to assemble.
- DO NOT tighten all screws and bolts until completely assembled.
- Keep all hardware parts out of reach of children.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM
NO
:
T
-
4096XXT
AND
T
-
4096XXB
REVISED NOV 20, 2012
Printed in Vietnam
THE HARDWARE REQUIRED TO ATTACH THE PEDESTAL IS PACKED WITH THE PEDESTAL. - 3 -
PART
LIST
When unpacking, please be careful not to discard any parts with the packaging. efore continuing, please make sure you
have the following parts:
NO
Des ription
Qty
Sket h
NO
Des ription
Qty
Sket h
A Top 1
Long leg 2
C Short leg 2
D Pedestal
column 2
E Crossbar 1
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. efore continuing, please make sure you
have all of the following hardware:
NO Des ription Qty Sket h NO Des ription Qty Sket h
1 Hexagon nut
(M8x13mm) 12
2 Flat washer
( Φ8.5x19mm) 12
3
Lock washer
( Φ8.5x11mm)
12
4
Wrench
(M13mm)
1
5 Wood screw
(M4x30mm) 4
6
olt
( M8x70mm)
2
7 Allen key
(4mm) 1
8 U-washer
(M8) 2

ITEM
NO
:
T
-
4096XXT
AND
T
-
4096XXB
REVISED NOV 20, 2012
Printed in Vietnam
THE HARDWARE REQUIRED TO ATTACH THE PEDESTAL IS PACKED WITH THE PEDESTAL. - 4 -
STEP 1
Attach crossbar (E) to pedestal columns (D) with bolts (6) and U-washers (8). Tighten with Allen key (7)
Attach legs (C) to legs ( ) with screws (5). Tighten with a screwdriver.
Attach legs ( & C) to pedestal columns (D) with nuts (1), and washers (2) and (3) as shown below.
Tighten with the wrench (4).
1
3
2
4
5
7
6
8

ITEM
NO
:
T
-
4096XXT
AND
T
-
4096XXB
REVISED NOV 20, 2012
Printed in Vietnam
THE HARDWARE REQUIRED TO ATTACH THE PEDESTAL IS PACKED WITH THE PEDESTAL. - 5 -
STEP 2
Using Allen key (7) to loosen bolts and washers and remove the mounting plates.
STEP 3
Attach mounting plates to the top of the pedestals (D) with nuts (1), and washers (2) and (3). Tighten
with wrench (4) as shown below.
A
7
1
3
2
4

ITEM
NO
:
T
-
4096XXT
AND
T
-
4096XXB
REVISED NOV 20, 2012
Printed in Vietnam
THE HARDWARE REQUIRED TO ATTACH THE PEDESTAL IS PACKED WITH THE PEDESTAL. - 6 -
Carefully place the base (from Step 3) on the bottom side of top (A). Attach mounting plates to table
top (A) with bolts and washers. Tighten with Allen key (7).
Unlock the table top from both sides underneath the table top. Pull the 2 parts of the top apart.
Place the leaves in the center of the open table top. Push the table top closed.
STEP 4
STEP 5
A

ITEM
NO
:
T
-
4096XXT
AND
T
-
4096XXB
REVISED NOV 20, 2012
Printed in Vietnam
THE HARDWARE REQUIRED TO ATTACH THE PEDESTAL IS PACKED WITH THE PEDESTAL. - 7 -
Lock the mechanism underneath 2 sides of the table top before use.
To unlock, press the button up from the steel glide before opening the leaf as shown below.
STEP