Whittier Wood Furniture 2319AFGACa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 01/13
Model #
2319AFGACa; 2319AFCAFa
McKenzie King Mantel Storage Bed
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended to
use this unit in a commercial setting.
Remove items before you move this unit.
Do not overload the drawers.
Before you load or move this unit, tighten all screws
and supports.
Before you begin your project, completely read the
Assembly Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a cold
and possibly damp cement floor).
Periodically inspect your furniture for any loose glue
joints, screws or any other problem that might affect the
stability of your furniture. Tighten or repair as needed.
This assembly requires two people.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE
CALL US FIRST! Do not return this item to the store.
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, contact Whittier Wood Products customer service
department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Parts List
2319AFGACa_2319AFCAFa —Page 2 —01/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
1318AFGACd; 1318AFCAFd Pedestal Kit (x2)
Part
Description
Quantity
E
#8 x 1-1/4" Black Screw (inserted)
30
Id
Pedestal Kit
1
J
Small Drawer Box (assembled)
2
Kd
Large Drawer Box (assembled)
1
L
Small Drawer Face (attached)
2
Md
Large Drawer Face (attached)
1
N
#8 x 1-1/2" Machine Screw (installed)
3
O
Knob (attached)
3
Pd
Deckboard
1
Q
Drawer Slides (installed)
3 sets
T
#8 x 2" Black Screw (inserted)
12
Y
#8 x 7/8" Lo-Profile Screw (inserted)
20
YD
#6 x 1/2" Philtruss Screw (inserted)
18
YE
#6 x 3/4" Philtruss Screw (inserted)
18
ZP
#8 x 1" Black Screw (inserted)
16
ZQ
Left Bracket (attached)
2
ZR
Right Bracket (attached)
2
ZX
#8 x 1-5/8" Black Screw (inserted)
16

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Parts List
2319AFGACa_2319AFCAFa —Page 3 —01/13
2320AFGACa; 2320AFCAFa
K. Mantel Headboard/Footboard Kit (x1)
Part
Description
Quantity
Aa
Headboard Assembly
1
B
Footboard Assembly
1
Rb
Center Deckboard
1
YH
Top Assembly
1
YI
#8 x 1-1/4" Pan Head Screw
2
YJ
Cam Connector (inserted)
2
YK
Cam Housing
2
ZP
#8 x 1" Black Screw (inserted)
32
ZQ
Left Bed Bracket (attached)
4
ZR
Right Bed Bracket (attached)
4
ZX
#8 x 1-5/8" Black Screw (inserted)
4

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Parts List
2319AFGACa_2319AFCAFa —Page 4 —01/13
2321W
K. Mantel Assembly Kit (x1)
Part
Description
Quantity
Da
Trestle With T-Nuts
7
E
#8 x 1-1/4" Black Screw
45
(9 inserted)
F
1/4" x 1-3/4" Hex Bolt
26
H
1/4" Flat Washer
26
Ua
Foot Assembly
3
W
Adjustable Glide (installed)
3
YD
#6 x 1/2" Philtruss Screw
8
YG
90oBracket
2
ZU
1/4" T-Nut (inserted)
28
ZV
#8 x 20mm Pan Head Screw (inserted)
12
ZY
Foot Bracket (attached)
3

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 5 —01/13
Tools Required: Phillips screwdriver, 7/16" open end or box end wrench and Tape measure
1. Remove the Center Deckboard (Rb) from the back of the Headboard (Aa) and place to the side.
See Figure 1.
2. NOTE: READ CAM INSTRUCTIONS NOW BEFORE YOU BEGIN THE FOLLOWING STEP.
Insert Cam Housings (YK) into the two pre-drilled holes on the Headboard Assembly (Aa) as
shown in Figure 2. Lower Top Assembly (YH) so that the Cam Connectors (YJ) fit into the
housings (YK) tighten the cam housings as indicated in the Cam-lock System instructions. See
Figures 2 and 2a.
Fig. 1
Shipping Straps
Rb
Aa
Fig. 2
Aa
YH
YK
x 2
YK
YK
Fig. 2a
YK
YJ

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 6 —01/13
3. Attach the Top Assembly (YH) to the Headboard Assembly (Aa) by inserting two #8x1-1/4" Pan
Head Screws (YI) into the predrilled holes in the block that is attached to the Headboard
Assembly (Aa). See Figures 3 and 3a.
4. Place both Pedestals (Id) approximately 79" apart as shown in Figure 4.
Fig. 3
YI
x 2
Fig. 3a
YI
Fig. 4
79"
Id
Id

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 7 —01/13
5. To attach the Footboard (B) to the Pedestal Assembly (Id), align the Brackets and slide the
Pedestal Assembly down on to the Footboard (B). See Figures 5 and 5a.
6. Repeat step two for the left side.
Fig. 6
Id
Fig. 6a
Fig. 5
Id
B
Fig. 5a

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 8 —01/13
7. Align the Brackets on both sides and slide the Pedestal/Footboard assembly down on to the
Headboard (Aa). See Figure 7.
Fig. 7
Aa

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 9 —01/13
8. Open the drawers. Face the Footboard and stand in between the first and second braces.
Place a Trestle with T-Nuts (Da) on the outside surfaces of the first upper left and right braces
so that the T-Nuts (ZU) sit near the top. See Figure 5a. Line up the upper edges of the trestle
and braces so they are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (H) and
tighten. Repeat for the second upper brace.
Place a Trestle with T-Nuts (Da) on the outside surface of the second lower brace so that
the T-Nuts (ZU) sit near the bottom. Line up the bottom edges of the trestle and braces so they
are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (H) and tighten.
See Figures 8 and 8a.
Fig. 8
Da
First brace
Second brace
Da
F
H
F
H
x 6
x 6
Footboard
Headboard removed for illustration purposes.
Fig. 8a
H
F
Brace
Da

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 10 —01/13
9. Face the Headboard and stand in between the third and fourth braces. Place a Trestle with
T-Nuts (Da) on the outside surfaces of the third upper left and right braces so the T-nuts sit
near the top. See Figures 6 and 6a. Line up the upper edges of the trestle and braces so they
are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (H) and tighten.
Place a Trestle with T-Nuts (Da) on the outside surface of the third left and right lower braces
so that the T-nuts sit near the bottom. Line up the bottom edges of the trestle and braces so
they are nearly flush. Insert two 1/4" x 1-3/4" Hex Bolts (F) and Washers (H) and tighten.
See Figures 9 and 9a.
Repeat for the fourth braces.
Fig. 9
Fourth brace
Third brace
Da
F
F
H
x 8
x 8
Fig. 9a
H
F
Brace
H
Trestle with T-Nuts (Da)
Da

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 11 —01/13
10. Facing the Headboard, place two Foot Assemblies (Ua) on the inside faces of the third and
fourth upper and lower Trestles. Attach with Washers (H) and 1/4" x 1-3/4" Hex Bolts (F).
See Figures 10 and 10a.
Fig. 10
Ua
F
H
x 8
x 8
Fig. 10a
H
Fourth set
of Trestles
Third set
of Trestles
Trestle with T-Nuts (Da)
H
Ua
F
Ua
F

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 12 —01/13
11. Facing the Footboard, place a Foot Assembly (Ua) on the inside of the second set of Trestles
and attach with four Washers (H) and four 1/4" x 1-3/4" Hex Bolts (F). See Figures 11 and 11a.
Place your bed in its final position. Adjust all three Glides (W) found at the bottoms of the Foot
Assemblies so that the Glides just touch the floor.
IMPORTANT: Make sure the Glides touch the floor and carry weight.
Fig. 11
F
H
x 4
x 4
Fig. 11a
Second set
of Trestles
H
H
Ua
F
F
W

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 13 —01/13
12. Facing the Footboard, attach a 90º Bracket (YG) to the Pedestal Assembly to the Footboard
with four #6 x 1/2" Philtruss Screws (YD). Repeat for the other side. See Figures 12 and 12a.
Fig. 12
Fig. 12a
YG
YD
YG
YD
x 2
x 8

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 14 —01/13
13. To make sure the bed is square, measure the distance between opposing corners. If one of the
measurements is larger, tap on a footboard leg until the measurement is equal. See Figure 13.
14. Place the Deckboards (Pd) as shown in Figure 14 and secure with twenty-four #8x1-1/4" Black
Screws (E). There should be a small gap between each deckboard.
Fig. 14
E
E
x 24
Pd
Fig. 13

2319AFGACa; 2319AFCAFa McKenzie King Mantel Storage Bed
Assembly Instructions
This assembly requires two people.
2319AFGACa_2319AFCAFa —Page 15 —01/13
15. Place the Center Deckboard (Rb) as shown in Figure 15 and secure with twelve #8 x 1-1/4"
Black Screws (E).
If you need to readjust the center feet, remove the Center Deckboard, adjust the glides and
reattach the deckboard.
Fig. 15
E
E
x 12
Rb

CAM - LOCK SYSTEM INSTRUCTIONS
P.O. Box 2827
Eugene, OR 97402 USA
Toll Free: 800-653-3336
Ph: 541-687-0213
Fax: [phone]
www.whittierwood.com
Page 1 of 1
Rev. 01/13
NOTE: To avoid scratching the surface of the
wood, assemble the unit and place face-down
on a clean, protected surface.
12 1
2
3
4
5
6
7
8
9
10
11
Optimum
tightness
Face of
Cam Housing
Correct way to tighten
your Cam-Lock system.
Cam Connector
Shoulder must be
flush with the surface
of the wood.
DO NOT embed
the shoulder into the wood!
1. Insert the Cam Housing so the arrow faces the Cam
Connector. To achieve tension and holding power,
you MUST TURN the Cam Housing clockwise at
LEAST 1/4 turn to the 9:00 position. Turning the
Cam Housing between 1/4 and 1/2 turn should be
enough to ensure rigid tension. Tension should be
initiated as soon as 10:00. You should receive
optimum tightness at 11:00. IF this does not occur,
tighten or loosen the Cam Connector to achieve
proper tension.
2. You may need extra tension if:
A. The Cam Connector was screwed in deeper or
not as deep as if should.
B. If the furniture is repeatedly assembled and
disassembled.
C. If you place a heavy load in the unit.
To achieve extra tension,tighten the Cam
Connector between the 11:00 and 12:00
positions.
Shelf
Side Panel
Cam
Connector
Cam
Housing
Install the Cam
Housing so the
arrow is directly
over the bolt.
Lock the Cam
Housing with:
Phillips
Screwdriver
Slotted
Screwdriver