Whittier Wood Furniture McKenzie 1123AFGACb User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 07/13
Model #
1123AFGACb;
1123AFCAFb
McKenzie Office Chest
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Do not overload the drawers.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

1123AFGACb; 1123AFCAFb McKenzie Office Chest
Parts List
1123AFGACb_1123AFCAFb —Page 2 —07/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Top Assembly
1
Ba
Case
1
C
Hutch Drawer (inserted)
2
D
Small Drawer Box (inserted)
1
E
Large Drawer Box (inserted)
1
F
Small Drawer Face (installed)
1
G
Large Drawer Face (installed)
1
H
Adjustable Shelf (attached)
1
I
Door (attached)
1
J
Insert Nut (inserted)
4
K
Small Adjustable Glide (installed)
4
L
Large Knob (attached)
4
M
#8 x 1-1/2" Machine Screw (installed)
4
N
Small Knob (attached)
3
O
4x32mm Machine Screw (installed)
3
P
Drawer Slides (pre-installed sets)
2
Q
#6 x 1/2" Philtruss Screw (inserted)
12
R
#6 x 3/4" Philtruss Screw (inserted)
12
S
Hinge (attached)
2
V
#6 x 5/8" Philtruss Screw (inserted)
4
W
#6 x 5/8" Undercut Screw ZN (inserted)
0 (AFGAC)
12 (AFCAF)
X
Door Stay (attached)
2

1123AFGACb; 1123AFCAFb McKenzie Office Chest
Parts List
1123AFGACb_1123AFCAFb —Page 3 —07/13
Part
Description
Quantity
Y
Shelf Bracket (attached)
4
ZA
#6 x 1/2" Undercut Screw (inserted)
4
ZB
#8 x 7/8" Lo-Profile Screw (inserted)
12
ZC
#8 x 1-1/4" Pan Head Screw (inserted)
14
ZD
#8 x 20mm Pan Head Screw (inserted)
4
ZF
#6 x 3/4" P. O Zinc Screw (inserted)
6
ZG
#6 x 1" P.OZinc Screw (inserted)
4
ZH
#8 x 1-3/8" Lo-Profile Screw (inserted)
8
ZI
Tuscan Magnetic Lock & Plate (pre-installed sets)
2
ZJ
#6 x 5/8" Undercut Screw AB (inserted)
16 (AFGAC)
4 (AFCAF)
TR
Furniture Tipping Restraint
2 sets

1123AFGACb; 1123AFCAFb McKenzie Office Chest
Assembly Instructions
1123AFGACb_1123AFCAFb —Page 4 —07/13
Tool Required: Phillips Screwdriver
1. Place the chest at its final destination. Rotate the Small Adjustable Glides (K) on the bottoms of
the legs until the unit is level. See Figure 1.
2. To move the Adjustable Shelf (H), remove the #6 x 1/2" Undercut Screws (ZA) and the Shelf
(H). Reposition the Shelf Brackets (Y) to the desired positions, replace the shelf and insert the
screws. See Figures 2 and 2a.
Fig. 2
H
ZA
Y
Fig. 2a
K
K
Fig. 1

1123AFGACb; 1123AFCAFb McKenzie Office Chest
Assembly Instructions
1123AFGACb_1123AFCAFb —Page 5 —07/13
3. Open the Door (I). To adjust the brake tension on the Door Stay (X), turn the screw on the Door
Stay (X) clockwise to loosen or counterclockwise to tighten. See Figures 3, 3a and 3b.
Continued on Page 6.
Fig. 3b
Fig. 3a
Fig. 3
L
o
o
s
e
n
T
i
g
h
t e
n
I
X
X

1123AFGACb; 1123AFCAFb McKenzie Office Chest
Assembly Instructions
1123AFGACb_1123AFCAFb —Page 6 —07/13
4. Tipping restraint: Locate two studs in the wall behind the unit. Attach a Clip (T1) to one wall
stud with two #8 x 2" Black Screws (T3). See Figure 4a. Attach a second clip to the unit with two
#6 x 5/8" Philtruss Screws (T5). See Figure 4b. Connect the two clips with the Nylon Restraint
Strap (T2). Pull the Nylon Restraint Strap (T2) tight so there is no slack. See Figures 4c and 4d.
Repeat this procedure to attach the second tipping restraint. If you cannot locate two studs,
purchase the proper wall attachment hardware for your type of wall and secure the unit.
Fig. 4a
T1
T3
Pull tight
Fig. 4d
T1
T2
T5
Fig. 4c
Pull the Nylon Restraint
Strap (T2) tight
so there is no slack.
T3
T5
T1
Fig. 4b