Whittier Wood 2906AFGAC User manual

Model #
2906AFGAC
48" Pedestal
Extension Table
Assembly Instructions
For normal household use only.
recommended for commercial use.
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading the Assembly Instructions before you begin
your project.
Do not climb, sit or stand on this piece of
furniture.
Completely read the Assembly Instructions before
you begin your project.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose
glue joints, screws, or any other problem that might
affect the stability of your furniture. Tighten or repair
as needed.
Service Policy: We will replace any parts
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
OOuuttsside ide UU..S. or Canada: S. or Canada: 554411--668877--00221133
MMaaiill: : PP.O.O. . BBoox 28x 28227 • 7 • EEugenugenee, , OOrregon egon 997744002, 2, UU..SS..AA..
FFaax: x: 554411--668877--2200660 • 0 • wwwwww..wwhhiittttieierrwwoooodd..ccomom
05/09VN
Production Code:
P.O. Box 2827
Eugene, OR 97402 USA

2906AFGAC 48" Pedestal Extension Table — Parts List
Before beginning assembly, check that the quantities of parts received match those listed below.
If you need to replace a part, please refer to the following list for name and number.
B — Pedestal
— Qty.1
A — Top Assembly
— Qty. 1
H — Top Support
(attached) — Qty. 1
J — Block #1
(attached) — Qty. 1
K — Apron Cleat
(attached) — Qty. 2
Y — Top Support Cleat
(attached) — Qty. 2
I — Leaf Apron
(attached) — Qty. 2
C — Foot — Qty. 4 G — Leaf Assembly — Qty. 1
2907AFGAC
2908AFGAC
X — Block #2
(attached) — Qty. 1
PART
ITEM
DESCRIPTION QUANTITY PART
ITEM
DESCRIPTION QUANTITY
D5/16"x3" Lag Bolt . . . . . . . . . . . . . . . . 4
E5/16" Flat Washer . . . . . . . . . . . . . . . . . 12
F 3/8" Hex Nut . . . . . . . . . . . . . . . . . . . . . 8
L#8 x 1¾" Pan Head Screw (inserted) . . 26
MB Leaf Hinge (attached) . . . . . . . . . . . . . . . 3
MA Apron Hinge (attached) . . . . . . . . . . . . 4
N Lever Lock (attached) . . . . . . . . . . . . . . 4
O Leveler Plate (attached). . . . . . . . . . . . 4
P #6 x 5/8" Flat Head Screw (inserted) . .
52
Q 3/8"x3½" Hanger Bolt (inserted) . . . . . . . 8
R Insert Nut (inserted) . . . . . . . . . . . . . . . . . 4
S Adjustable Glide (attached). . . . . . . . . . . 4
T 3/8" Guide Pin (inserted) . . . . . . . . . . . . . 8
U ½" x 2¼" Wood Dowel (inserted) . . . . . . .
. . . . .
4
V Slide (installed) . . . . . . . . . . . . . . . . . . . . . 2 sets
W #12 x 1¾" Pan Head Screw (inserted) 16
. . . . . . . . . . . . . . . .
ZA Apron Cap (attached) 4
ZB 90° Bracket (attached) . . . . . . . . . . . . . . . . 4
ZC #6 x 5/16" Flat Head Screw (inserted). . . . . 8
ZD #6 x ¾" Brass Flat Head Screw (inserted). . 8
Page 2 — 2906AFGAC — 05/09

ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED:
Phillips Screwdriver, Mallet or Padded Hammer, 9/16" Wrench and 7/16" Wrench, Wood Glue
Page 3 — 2906AFGAC — 05/09
2906AFGAC 48" Pedestal Extension Table
DOWEL HOLE
Fig. 2
Fig. 2a
Fig. 1a
FE
C
B
Q
2. Turn the Pedestal (B) upside-down so the top end of the pedestal is on the floor. Apply a light film
of glue into each of the four dowel holes in the Pedestal. See Figure 2a. Insert the Foot (C)
into the holes on the Pedestal (B). With a damp rag, quickly wipe off any excess glue. The Hanger
Bolts (Q) should go all the way through the base. Gently tap feet into place with padded hammer.
Fasten in place with 5/16" Washer (E) and 3/8" Hex Nut (F). See Figure 2.
Place the Top Assembly (A) upside down on a clean, protected surface and remove the Feet (C)
as seen in Figure 1 and place them off to the side. Unlatch the locks. Turn the top assembly
right-side up and pull open the table ends to expose the Leaf Assembly (G). Remove the Leaf
Assembly (G) and set it off to the side. See Figure 1a. Remove the foam now, but when you store
the leaf, place foam in between the folded leaves. This will help protect its surface.
1.
G
Fig. 1
G
C
Shipping Straps
A
Leaf Hinge and Lever Lock
Leaf Hinge
and Lever
Lock

Page 4 — 2906AFGAC — 05/09
Fig. 4b
Fig. 4
G
D
E
Fig. 3
E
D
Fig. 3a
A
S
C
3. Turn the Pedestal right-side up and line up the pre-drilled holes in the Top Assembly
to the pre-drilled holes in the pedestal. Attach using four 5/16"x3" Lag Bolts (D) and four 5/16"
Washers (E) as shown in Figures 3 and 3a. To level the table, turn the Adjustable Glides (S)
on the bottom of each Foot (C).
4. To insert the leaf, flatten out the Leaf Assembly (G) as shown in Figure 4. Flip open the Apron on
each end of the leaf assembly as in Figure 4a and turn it right-side up. Place it in the open space
between the table ends and line up the dowel and dowel holes. Gently push the table ends until the
leaf fits snugly. See Figure 4b. Close the locks that are underneath the table.
Fig. 4a
G

Fig. 5c
Page 5 — 2906AFGAC — 05/09
Fig. 5 Fig. 5a
G
5. To remove the leaf, release the locks underneath the table. Gently pull away the table ends until
the dowels pull out of the dowel holes. Lift out the leaf and place it on a clean, protected surface.
See Figure 5. Push flat the apron on each end of the leaf. See Figure 5a. To protect the finish, place
foam in between the leaves. Fold the leaf in half as shown in Figure 5b. Place the folded leaf
in the storage area underneath the table ends and push the ends tightly shut. See Figure 5c.
Fig. 5b
G