Whittier Wood 3501GACc User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 03/17
Model #
3501GACc
3501CAFc
McKenzie End
Table
GAC = Glazed Antique Cherry finish
CAF = Caffè finish
Assembly
Instructions
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Do not climb, sit or stand on this piece of furniture.
•Unload items before you move this unit.
•Do not overload the drawers.
WARNING
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

3501GACc, 3501CAFc McKenzie End Table
Parts List
3501GACc_3501CAFc — Page 2 — 03/17
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
Ac
Case Assembly
1
Bc
Top Assembly(attached)
1
C
Leg
4
E
Drawer (inserted)
2
F
Drawer Face (installed)
2
G
20" Drawer Slides (pre-installed sets)
2
H
#6 x 3/4" Philtruss Screw (inserted)
12
I
#6 x 1/2" Philtruss Screw (inserted)
12
J
Knob (attached)
2
Kb
#8 x 1-1/2" Machine Screw Tuscan (installed)
2
M
Adjustable Glide (installed)
4
N
#8 x 1-1/4" Pan Head Screw (inserted)
40
Ob
#8 x 7/8" Black Lo-Profile Screw (inserted)
8
P
3/8" x 1" Insert Nut (inserted)
8
Q
5/16" Flat Washer
8
R
3/8" x 2-1/2" Hex Bolt
8
S
1/4" x 20mm Insert Nut (inserted)
4
U
#8 x 1-3/8" Lo-Profile Screw (inserted)
2
V
#10 x 2" Pan Head Screw (inserted)
6
W
#8 Washer (inserted)
6
X
Top Support (attached)
2

3501GACc, 3501CAFc McKenzie End Table
Assembly Instructions
3501GACc_3501CAFc — Page 3 — 03/17
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench
1. Remove the Drawers (E) from the Case Assembly (Ac). To remove the drawers, pull up on the
left side of the Drawer Release Lever while pushing down on the right Drawer Release Lever.
See Figure 1a. Note where each drawer came from to ensure correct installation.
2. Turn the unit upside down on a clean, protected surface. Place two Legs (C) at the front corners
of the Case Assembly (Ac) making sure the drilled corners of the legs face toward the Corner
Blocks. Insert two 3/8" x 2-1/2" Hex Bolts (R) with two Flat Washers (Q) through the Corner
Blocks and into the leg and fasten securely. See Figures 2 and 2a. Repeat for the other two
legs.
Fig. 2
Q
R
x 8
x 8
Fig. 2a
Q
R
C
C
R
Q
Ac
Fig. 1
Drawer Release Lever
Fig. 1a

3501GACc, 3501CAFc McKenzie End Table
Assembly Instructions
3501GACc_3501CAFc — Page 4 — 03/17
3. Turn the table upright and insert the Drawers (E).
4. Place the table at its final destination. To level the table, rotate the Adjustable Glide (M) found at
the bottom of each leg. See Figure 3.
Fig. 3
M
M