Willy's RC Angel User manual

-------------Angel ---------------
Multi-rotors Aircraft manual

01 工具 Tools
02 飞行前的准备 Before Flight
ATTENTION : These all screws of the product is not add glue, pls use the glue of screw to reinforce the track of screw
before your application.
Transmitter (6-channel or more) Receiver (6-channel or more) 11.1V ( 3S) 2200~5500mA/h
11.1V 2200~5000ma/H
:Radio transmitter and electronic equipment required for assembly
Hexagon Screw Driver
1.5mm/2mm/2.5mm Cross Screw Driver Sharp nose pliers Screw Glue
:Additional tools required for assembly
DISCLAIMER OF LIABILITY
1.Using the company products within the limits permitted by local laws and
regulations. the company is not responsible for any illegal activities.
2.The Bumblebee is an aeromodelling product only. Please strictly follow the
aeromodelling safe function rules, the company does not hold responsible for
any control over its operation or usage.
3.Model aircraft are not toys! Fly under professional guidance and strictly
follow instruction rules in this document. the company is not responsible for
consequences caused by improper install, wrong setting or operation.
SAFETY CAUTIONS
1. Familiarize yourself with fly environment and any obstacles. Identify any
potential hazards such as power lines, cars, people, etc.
2.Do not fly the aircraft when fatigued, drunk or your mental state has been
compromised which may cause an accident.
3.Stay away from wet areas. Do not fly in the rain or wet environments which
can cause device failure and probably lead to danger. Do not fly at night or
in windy conditions.
5. Do not fly alone during your preliminary flights. If you need help, please
enlist the aid of an experienced pilot before flying for the first time.
6. Prepare rescue tools such as cell phones or other communication devices
which should you need to call for help.
7. Please fly under safe take-off weight, do not overload the aircraft which can
lead to danger.
8. Ensure all the equipment operates correctly before flight and that there is
no transmitter interference or conflicts.
9. Do not touch any moving or powered parts. Do not try to catch the
quadcopter which has rotating motors or blades for example. Keep loose
clothing away from moving parts as they may get caught and could cause
physical harm.
10. Always throttle down to minimum before fly.
11. Remove the propellers when testing the remote device or motors operation.
Attach the propellers after you have tested that everything is working good
to prevent an accident.
12. Assemble the aircraft with accessories the company provides. the company
is not responsible for any consequence resulted from assembly with other
accessories or modifications.
4. Stay away from any fire resulting in damage of the electronic parts or others
such as the flight battery.

03 LED模块和电池仓LED Plate and battery door
04 电机和电调 Brushless Motor and ESC
M4
M1
M2
M3
注意：
电机分两种(CW和CCW ),M1和M3安装CW的电 机，
M2和M4安装CCW电机，切勿装反。机架上有
M1,M2,M3,M4标识，电机包装袋上有CW和CCW标识。
Note:
Motor has two kinds(CW and CCW)
Motor M1 and M3 are installed in motor
CW, While M2 and M4 are installed
in CCW motors.
all of them will have tags on their
package,like
M1,M2,M3,M4. also with sign
“CCW” or “CW”.
pls pay attention to the motor ’s
direction.
M3*6螺丝
Screw M3*6
LED 灯罩
lampshade
LED 灯板
LED lamp board
无刷电调
brushless ESC
LED 灯罩
LED lampshade
参数调整模块
parameter adjustment board
机架下板
lower fuselage
插销
bolt
电池仓门
battery door

05 中心板和飞行控制器Centre board and Flight controller
06 云台的组装Gimbal installment
LED 灯罩
LED lampshade
减震球
dampling ball
螺丝Screw
螺母NUT
中心板
cen t r e p l a t e
自攻螺丝PA2*6
Screw PA2*6
飞行控制器
Flight controller
自攻螺丝PA2*6
Screw PA2*6
M1
M3
M2
M4
注意：
包装袋上 贴 有CCW标识 的电机
安装在M1、M3位置 ， 贴有CW标
识的电机 安 装在M2、M4位 置。
Warning:
pls install the motors with
“CCW”sign in M1 and M3 location,
while those with “CW”installed
in M2 and M4 location
!

07 起落架的安装 Landing gear Assembling
08 云台的安装 Gimbal Assembling
起落架
Landing Gear
螺丝M2.5*6
Screw M2.5*6
螺丝M2.5*6
Screw M2.5*6
螺丝M2.5*6
Screw M2.5*6
云台
Gimbal

09 螺旋桨的安装 Propeller Assembling
螺旋桨
pro p el l er
9443正 桨： 安装在M1、M3位 置。
9443 propeller(cw)istalled in M1 and M3
银色
siliver
安装前请确认M1&M3位置安装的电 机 为CCW（反牙）,M1&M3位 置 电 机旋转方向为逆时针旋
转;M2&M4位置安装的电机为CW（正牙）,M2&M4位置电机旋转方向为顺时 针 旋 转 ，
Before installing, Please make sure that motors( CCW )should put in M1&M3 place;
M1&M3's rotation direction is counterclockwise. However, motors(CW) should put in
M2&M4's direction is clockwise.
M1 & M 3
ccw
反牙
cc w tooth
9443反桨：，安装在M2、M4位置
9443 propeller (CCW)installed in M2 and M4。
黑色
Bl a c k
M2&M4
cw
正牙
cw t oo th
02 ***************
M1M2
M3 M4
正牙电机
cw mo t o r
反牙电机
CCW motor
10 电路接线示意图 Cirouit Wiring:
接收机接线示意图：
Flight Controller
Flight Controller
正牙电机
cw mo t o r
反牙电机
CCW motor