WilTec 51800 User manual

User’s manual
Hydraulic Gear Puller
51800
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.

© by WilTec Wildanger Technik GmbH Item 51800 Page 2
http://www.WilTec.de
http://www.aoyue.eu 03 2022-1
http://www.teichtip.de
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler Germany
Do you wish to collect your goods? Our address for collection is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler Germany
In order to shorten the waiting time and to allow for an easy on-site processing, we kindly ask you to
contact us briefly beforehand or to place your order via the webshop.
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]
To return your goods for exchange, repair, or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler Germany
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]

© by WilTec Wildanger Technik GmbH Item 51800 Page 3
http://www.WilTec.de
http://www.aoyue.eu 03 2022-1
http://www.teichtip.de
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Safety instructions
Before using the device, make sure to read and understand this manual.
Warning! Pulling off components might require an increased effort. Therefore, always make sure to
obey all safety precautions when pulling off.
•During work, wear appropriate protective equipment, such as working gloves, protective gog-
gles, safety shoes, etc.
•While pulling off, use a protective tarpaulin to avoid injuries and accidents.
•Before each use, check to condition of the hydraulic gear puller. Components worn or damaged
must be replaced immediately. Never use a damaged puller tool to avoid accidents and injuries.
•Do not modify the device in any way. Any incorrect use will increase the risk of accidents and
injuries.
•Safely apply the puller and always control the necessary effort during pulling. Should anything
indicate overload (e.g., stiffness), immediately interrupt pulling. In that case, choose a different
pulling part.
•Keep the shafts or traverses clean and well-lubricated.
•Always control the force input and never exceed the maximum load specified.
•To work the gear puller, never use additional electric or pneumatic impact wrenches.
•Do not extend it to increase the torque. This might lead to overload and breaking.
1. The capacity of a combined assembly (e.g., a puller with hydraulic system) always depends on
the weakest element.
2. To simplify pulling, components may be warmed up.
Attention! Nevertheless, the puller itself must never be warmed up, as this could impair its
stability properties.
3. The gear puller should be maintained regularly to increase its service time and ensure safe
operation.
Parts list
Name
Qty.
Name
Qty.
Hydraulic ram
1
Ram ring
1
Puller leg
9
Puller for separation of bearings
1
Traverse to 2-leg puller
1
Traverse for puller for bearings
1
Traverse to 3-leg puller
1
Extension for puller for separation of bear-
ings
2
Extension for shaft
3
Tie rods for puller for separation of bear-
ings
2

© by WilTec Wildanger Technik GmbH Item 51800 Page 4
http://www.WilTec.de
http://www.aoyue.eu 03 2022-1
http://www.teichtip.de
Use
1. Make sure that the work piece is only held by interference fit (parallel or taper).
2. Fix the appropriate puller (see fig. 1) and adjust the T handle (fig. 2, A) so that the puller (fig. 2,
B) is approximately 80 mm above the top of the ram (see fig. 2).
3. Apply the pulling legs behind the work piece. Then screw the ram body down, using the centre
adaptor at the end of the piston until the point of the adaptor engages the end of the shaft from
which the work piece is to be pulled off. If necessary, use an extension bar.
4. Turn the T handle clockwise by hand to pull the work piece off the shaft.
5. Do not screw the T handle in further than 25 mm from the end of the ram (see fig. 2). Should
the work piece need to be moved additionally, unscrew the T handle to 80 mm from the end of
the ram. Screw then ram body down so that the centre adaptor again contacts the shaft. Then
continue to pull the work piece off the shaft.
Important! The maximum safe load of the puller may only be reached by hand. Using tools or levers to
increase the load can damage the puller and cause injuries.
If the work piece does not move even with maximum effort, do not try to loosen the work piece or puller
by hitting it. This might cause damages to the puller/work piece and injuries. In that case, use a bigger
puller.
Figure 1
Figure 2
Important Note:
Reproduction and any commercial use (of parts) of this operating manual, requires a written permission
of WilTec Wildanger Technik GmbH.