WilTec XPOtool 64158 User manual

User’s manual
Hose reel
64158
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

https://www.XPOtool.com Item 64158 Page 2
The Tool Experts
02 2023-1
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler – Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler – Germany
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]

https://www.XPOtool.com Item 64158 Page 3
The Tool Experts
02 2023-1
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Before using the reel
•This product has been packed to arrive in the best possible condition. Please be careful when
unpacking it.
•Before assembly, read the user’s manual.
•This kit contains pieces that could be damaged when assembled incorrectly. Please obey the
instructions concerning the correct assembly.
Scope of delivery
Figure
Name
Quantity
Reel
1
Hand crank
1
Water-system inlet
1
Hose guiding unit
1
Brass adaptor (for connection to water system)
2
Guide hose
1
Stop ball
1
Tools needed
•Cross-head screwdriver
•Sealing tape (optional, not included)

https://www.XPOtool.com Item 64158 Page 4
The Tool Experts
02 2023-1
Mounting
Carefully take all pieces out of the box.
Step 1: mounting the hose guiding system
1. Determine the hose-guiding-system piece.
2. Set the hose-guiding-system piece into the tubes (see figure).
Step 2: mounting the hand crank and water-system inlet
1. Set the hand crank to the axle.
2. Fix it with the help of the screw included in the scope of delivery.
3. Install the water-system inlet. Push down the locking lever and set the water-system inlet in,
giving it the alignment desired.
4. Make sure that the inlet tube is pushed in totally before closing the locking lever.
5. Then remove the guide hose from the drum.
6. Set one end of the guide hose into the water inlet and tighten the threaded coupling by hand.
Step 3: connecting adaptor to water system
1. Take the adaptor piece out.
2. Install the adaptor to the water system (see illustration).

https://www.XPOtool.com Item 64158 Page 5
The Tool Experts
02 2023-1
Step 4: connect hose with reel
1. Set the adaptor to the inlet and outlet water system.
2. Attach the C clamp to the ends of the hose connected to the inlet/outlet water system.
3. Guide the hose into the inlet/outlet water system, making sure that it penetrates deeply.
Step 5: adjusting the stop ball
The position of the stop ball can be adjusted to determine the length of the hose that stays outside the
reel when the hose is reeled up.
1. Extract the hose to the desired length.
2. Open the lock of the stop ball and slide it to the desired position.
3. Re-lock the ball.
Attention! Make sure that the stop ball is fixed securely before unlocking the drum.

https://www.XPOtool.com Item 64158 Page 6
The Tool Experts
02 2023-1
Use
1. Extract the hose to the desired length.
2. Open the water supply by opening the water tap.
3. Use the hose for watering.
4. Before reeling the hose up, return to the device, holding the nozzle, then turn off the water, and
press the nozzle for a few seconds to release the pressure built up inside the hose.
5. Reel up the hose. It might be helpful to hold the device with one foot while using the hand crank.
Maintenance and care
Annual lubrification of seals
To avoid leakage and to extend the service life of the seals of the water inlet, these should be lubricated
once a year (see Fig. 1).
1. Turn off the water supply to the device by closing the tap.
2. Let the locking lever loose (see Fig. 2).
3. Pull the inlet tube off the axle.
Fig. 1
Fig. 2
Storage
•Turn off the water when not using the hose reel.
•Store the device indoors when it is not in use.
•To avoid damage from expanding ice, always unplug and drain all hoses during the winter
months to prevent freezing.
•Clean the hose with mild soap and water only.
Important note: Reproduction and any commercial use (of parts) of this operating manual, requires a
written permission of WilTec Wildanger Technik GmbH.