Winbond Flash Memory Sample Shield User manual

USER GUIDE
Winbond Flash Memory Sample Shield
[1] Publication Date: December 4, 2017 Revision 2.0
1. INTRODUCTION
This describes how to use the Winbond Flash Memory Sample Shield. The mbed enabled MCU
board, which has an Arduino UNO R3 compatible terminal, is used in this description.
2. GENERAL DESCRIPTION
The Winbond Flash Memory Sample Shield from Winbond Electronics is an Arduino-derived
shield that will interface with any Arduino-derived microcontroller host board with a standardized
Arduino UNO R3 pinout.
The Winbond Flash Memory Sample Shield is mounted with the flash memory listed below.
Part Number
Density
Product Type
Operation Temperature
W25Q80NESNIG
8Mb
1.2V Serial NOR Flash Memory
Industrial (-40’C to +85’C)
W25N01GVZEIG
1Gb
3.3V Serial NAND Flash Memory
Industrial (-40’C to +85’C)
W25M161AVEIT
16Mb + 1Gb
SpiStack 3.3V Serial NOR + Serial
NAND Flash Memory
Industrial (-40’C to +85’C)
W74M12FVZPIQ
128Mb
3.3V Serial NOR Flash Memory +
Authentication
Industrial (-40’C to +85’C)
3. OPERATION CONFIRMED HOST BOARDS
Host Board Supplier
Host Board
MCU
STMicroelectronics
NUCLEO-F411RE
STM32F411
4. HOW TO USE WITH NUCLEO-F411RE
Besides the host board and the Winbond Flash Memory Sample Shield, you will need:
1
Computer with Internet access and USB port.
USB cable with standard A to mini B connectors.
Sample program source code.
1
Please install “Arm Mbed Windows serial port driver” as necessary. https://os.mbed.com/handbook/Windows-serial-configuration

USER GUIDE
Winbond Flash Memory Sample Shield
[2] Publication Date: December 4, 2017 Revision 2.0
Step.1 Solder the terminal to Winbond Flash Memory Sample Shield
Solder the terminals for CN1~4, JP1~7 and J1~4 as shown in the red frame in the picture below.
CN1~4 should be toward below of the board. JP1~7 and J1~4 should be toward above of the
board.
Step.2 Place the jumper pin and switch its positions
The Winbond Flash Memory Sample Shield is mounted with 4 kinds of Flash Memory. It is
necessary to switch the position of the jumper pin for JP1~7 and J1~4 according to the Flash
Memory you want to use. When switching the position of the jumper pin, be sure to do with
the Winbond Flash Memory Sample Shield removed from the host board. The position of
the jumper pins other than the following 4 types is prohibited. Flash Memory may be
damaged.
1. Jumper pin positions for 1.2V Serial NOR Flash Memory
・Place a jumper pin to JP1 for chip select
・Place a jumper pin to JP5 for 1.2V Vcc
・Place jumper pins at positions 1 and 3 of J1~4
Sample program source code: “SPI_NOR.zip”

USER GUIDE
Winbond Flash Memory Sample Shield
[3] Publication Date: December 4, 2017 Revision 2.0
2. Jumper pin positions for 3.3V Serial NAND Flash Memory
・Place a jumper pin to JP2 for chip select
・Place a jumper pin to JP7 for 3.3V Vcc
・Place jumper pins at positions 2 and 4 of J1~4
Sample program source code: “SPI_NAND.zip”
3. Jumper pin positions for SpiStack 3.3V 16Mb Serial NOR + 1Gb Serial NAND Flash Memory
・Place a jumper pin to JP3 for chip select
・Place a jumper pin to JP7 for 3.3V Vcc
・Place jumper pins at positions 3 and 5 of J1~4
Sample program source code: “SPISTACK.zip”

USER GUIDE
Winbond Flash Memory Sample Shield
[4] Publication Date: December 4, 2017 Revision 2.0
4. Jumper pin positions for 3.3V Serial NOR Flash Memory + Authentication
・Place a jumper pin to JP4 for chip select
・Place a jumper pin to JP7 for 3.3V Vcc
・Place jumper pins at positions 4 and 6 of J1~4
Sample program source code: “SPI_NOR.zip”
Step.3 Get sample program source code
Please access URL below to get sample program source code.
http://www.winbond.com.tw/hq/about-winbond/news-and-events/events/product-
promotion/promotion00020.html?__locale=en
When you get sample program source code “SPI_NOR.zip”, “SPI_NAND.zip”, “SPISTACK.zip”.
Then unzip it.
2
Step.4 Plug in the Winbond Flash Memory Sample Shield to your computer
Plug the Winbond Flash Memory Sample Shield into your host board, then connect the host
board to your computer using USB cable. The host board will enumerate as a composite USB
device that includes a built in debugger, storage device and a virtual com port.
2
Please use “SPI_NOR.zip” to operate flash memory of W74M12FVZPIQ. If you would like to use W74M12FVZPIQ
authentication function, please contact the following e-mail address.
SalesSup[email protected]

USER GUIDE
Winbond Flash Memory Sample Shield
[5] Publication Date: December 4, 2017 Revision 2.0
A new drive will be created on your computer with a drive name as assigned by the host board.
We are using the NUCLEO-F411RE as an example for this Setup description.
Before mounting the Winbond Flash Memory Sample Shield After mounting the Winbond Flash Memory Sample Shield

USER GUIDE
Winbond Flash Memory Sample Shield
[6] Publication Date: December 4, 2017 Revision 2.0
Step.5 Log in to ARM mbed and create a Workspace
1. Log in to developer.mbed.org. (If you don’t have an mbed account, please create it.)
2. After log in, click on the Compiler button, then thembed compiler will bring up the Workspace.
Step.6 Load the platform for the host board
1. Click on the upper right button to open the available compiler platforms screen. Select the
host board platform you wish to load or, if it is not present, then select [Add].
2. If you selected Add, mbed will display a scrolling list of available platforms. Find the host
board you are using and click on the image.

USER GUIDE
Winbond Flash Memory Sample Shield
[7] Publication Date: December 4, 2017 Revision 2.0
3. mbed will open a new window as an information page for that host platform, such as the
NUCLEO-F411RE example here. To add this platform to your workspace, click on the [Add
to your mbed Compiler] button.
Step.7 Import the sample program source code
1. In your Workspace, click [Import]. The Import a program dialog box will open. Click on the
[Upload] tab. Click on the “Add File”, select sample program source code and “main.cpp”,
and click [Import!].

USER GUIDE
Winbond Flash Memory Sample Shield
[8] Publication Date: December 4, 2017 Revision 2.0
2. Select “Programs” in “Import As:”, and input any name in “Import Name:”
3. One more time, click [Import]. The Import a program dialog box will open. Click on the
[Libraries] tab. Search for the “mbed” libraries, select it and click [Import!].

USER GUIDE
Winbond Flash Memory Sample Shield
[9] Publication Date: December 4, 2017 Revision 2.0
4. Select “Library” in “Import As:”, and input the same name as inputted in step7-2 to “Target
Path:”
5. The sample program will now appear in the Program Workspace.

USER GUIDE
Winbond Flash Memory Sample Shield
[10] Publication Date: December 4, 2017 Revision 2.0
Step.8Compile the sample code and load to host board
1. Highlight the sample program folder in your Workspace tree in the left-hand column.
2. Click [Compile] in the top menu.
3. The program will be compiled and the binary (.bin) file created will automatically be
downloaded to your computer’s designated download location.
4. Drag and drop the binary file into the host board drive that you created in Step.4. When the
file is dropped into the folder, your host board will begin to program. When the program is
fully loaded, the binary file will automatically delete from your host board drive.

USER GUIDE
Winbond Flash Memory Sample Shield
[11] Publication Date: December 4, 2017 Revision 2.0
Step.9 Run sample program by terminal emulator
1. Use your favorite terminal emulator. For this example, we used the Tera Term.
2. Open Tera Term and select the serial port associated with your host board to create a new
connection.
3. Configure the serial port under Setup->Serial port with: 9600 baud, Setup->Terminal with:
line feed code as LF.
4. Press the Reset button on your host board to run the sample program.

USER GUIDE
Winbond Flash Memory Sample Shield
[12] Publication Date: December 4, 2017 Revision 2.0
5. SCHEMATIC

USER GUIDE
Winbond Flash Memory Sample Shield
[13] Publication Date: December 4, 2017 Revision 2.0
6. PCB LAYOUT

USER GUIDE
Winbond Flash Memory Sample Shield
[14] Publication Date: December 4, 2017 Revision 2.0
7. REFERENCE
1. 1.2V Serial NOR Flash Memory Product Introduction
https://www.winbond.com/hq/product/code-storage-flash-memory/1.2v-serial-nor-
flash/?__locale=en
2. 3.3V Serial NAND Flash Memory W25N01GVZEIG Datasheet
https://www.winbond.com/resource-files/w25n01gv%20revg%20032116.pdf
3. SpiStack 3.3V Serial NOR + Serial NAND Flash Memory Datasheet
https://www.winbond.com/resource-
files/w25m161av%20combo%20reva%20091317%20mod%20final.pdf
4. Authentication Flash Product Introduction
https://www.winbond.com/hq/product/code-storage-flash-memory/authentication-
flash/?__locale=en
5. Arm Mbed Windows serial port driver
https://os.mbed.com/handbook/Windows-serial-configuration
https://os.mbed.com/docs/latest/tutorials/windows-serial-driver.html

USER GUIDE
Winbond Flash Memory Sample Shield
[15] Publication Date: December 4, 2017 Revision 2.0
Revision History
Version
Date
Page
Description
1.0
11/07/2017
NA
New Create
2.0
12/04/2017
10, 11
Correct step number of title and sentence
Trademarks
Winbond, SpiFlash and SpiStack are trademarks of Winbond Electronics Corporation.
All other marks are the property of their respective owner.
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment
intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation
instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or
sustain life. Furthermore, Winbond products are not intended for applications wherein failure of Winbond products could
result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur.
Winbond customers using or selling these products for use in such applications do so at their own risk and agree to
fully indemnify Winbond for any damages resulting from such improper use or sales.
Information in this document is provided solely in connection with Winbond products. Winbond reserves the
right to make changes, corrections, modifications or improvements to this document and the products and
services described herein at any time, without notice.