Windoware HONEYCOMB User manual

Installation of Brackets – Inside Fit
• Measure 55mm at the cordlock side, each jam for end
bracket location and make a mark for each
• If you are given more than two installation brackets with
your order, space the additional brackets evenly between
the two end brackets.
• Centre each bracket on the marks you have made and then
mark where the screw holes need to be made.
• Check the surface where you will be mounting the brackets
to ensure it is level and the brackets are aligned.
• Drill the screw holes. NOTE: installation may require wall
anchors. (These are not provided)
• Fasten the brackets to the mounting surface by using the
screws provided.
To adjust the drop height and level the bottom rail:
• Loosen the cord on the ferrule
• Slide the ferrule up or down until the bottom rail is at the ordered drop height
• Tighten the cord on the ferrules
• Push the ferrules into the pockets non handleson there
• Again check the drop height and level. Adjust if necessary
CAUTION: Do NOT trim the excess cord under the ferrules. The installer will trim them after
making final adjustments during installation.
Installation of Brackets – Outside Fit
• Centre the head rail over the window opening at the height you wish. Lightly mark each end
of the head rail using pencil.
• Measure and mark 8cm in from both ends of the head rail.
• If you are given more than two installation brackets with your order space the additional
brackets evenly between the two end brackets.
• Centre each bracket on the marks you have made and then mark where the screw holes need
to be made. NOTE: The rear of the brackets must be flush against a flat mounting surface -
DO NOT mount brackets to a curved surface.
• Drill the screw holes. NOTE: installation may require wall anchors. (These are not provided)
• Fasten the brackets to the mounting surface by using the head screw provided.
HONEYCOMB
Installation Operation Care 2015
Re-order 9699
Care and Cleaning
Honeycomb blinds are anti-static, dust resistant fabric.
For most honeycomb fabrics, the following options are available if your blind needs cleaning:
Please take care with the Blockout as the metallic coating inside is very delicate.
Dusting Regular light dusting with a feather duster is all that is needed in most
cases.
Vacuuming For deeper cleaning, vacuum gently with a brush attachment.
Spot Cleaning Prepare a solution of warm water mixed with a mild detergent.
Dampen a clean cloth in the solution and wring it out well.
Dab the spot you want to clean with the dampened cloth until it is gone.
DO NOT rub the fabric.
Allow the blind to dry in the fully lowered position
Removal of Blind for cleaning
• Fully raise the blind.
• Unscrew the tab screw on each bracket to release
the head rail taking care not to fully unscrew it to
make replacement easier.
Before you install into brackets, release the cord lock by about 30 mm so that it is easier to
clip the blind into the back of the bracket. You should hear an audible click. You then need
to shift the fabric out of the way of the back of the headrail so you can tighten the screw up.
All manuals and user guides at all-guides.com

Trouble Shooting
Problem
The shade does not fit into
installation brackets
The shade is hard to lower
and lift, or will not lower or
lift at all
The shade will not lower
when pulling on the cord
The shade will not stay in
the lifted position
Operating your Honeycomb
• Be sure to keep the cord close to the fabric when
operating shade.
• To move the shade up or down, disengage the
cord lock by moving the cord to the centre of the
shade. Pull on the cord to lift the shade.
• Engage the cord lock by placing the cord back
to the original position.
• With all operations with the Blind ensure that the
cords do not twist or tangle.
Always use two hands to guide the blind up and
down, never release the blind and let it fall on its
own as this can cause the cords to twist.
Make sure installation brackets are level and aligned.
Make sure the heads of the mounting screws are flush against
the installation bracket and not sitting above it.
Make sure that the blind fabric is not caught between the
bracket and head rail.
Make sure the head rail and brackets are level and aligned.
Measure window to make sure it is square (measure diagonals).
Make sure the cords are not caught or tangled.
Make sure the shade fabric is not caught between the brackets.
Make sure the hold down brackets are released before the
operation of shade (If they are used).
Make sure the locking mechanism in the cord lock is released.
Pull the cord into the centre at about a 45 degree angle to
release cork lock. Let go of cord to drop shade.
Make sure you engage the cord lock by pulling on cord
towards the outside of the shade. This will lock the shade in
place.
Installation of Blind into Brackets
• Unwrap cords and position the Blind so that the
cords are facing you.
• Slide the head rail into the brackets so the front of
the bracket slides under the front groove on the top
of the head rail.
• Carefully roll the back of the head rail up and then
push back to click into place.
• Tighten the tab screw well but do not over tighten
Adjust the drop height and level the bottom
The drop height must be
equal to the ordered height
or up to 1/4” longer.
The height must be equal
on both sides of the shade.
Push the ferrules into the
pockets and check the
adjustment.
All manuals and user guides at all-guides.com