Wine Guardian D050 User manual

1
Ducted Wine Cellar Cooling Systems
Installation, Operation and Maintenance Manual
D025, D050, D088, D0200
Manufactured by:
Syracuse, NY
www.wineguardian.com www.airinnovations.com
Wine Guardian reserves the right, without notice, to make changes to this document at its sole discretion.
Please visit out web site for the most current version of the Wine Guardian manual and other literature.
Wine Guardian is a registered trademark (2,972,262) of Air Innovations, Inc.
Edition 3/2012
© Air Innovations 2012

2
TABLE OF CONTENTS
Directory of Terms ...........................................................................................................5
Illustrations ......................................................................................................................6
Receiving, Inspecting and Unpacking the Wine Guardian Unit........................................7
Receiving and Inspecting the Unit ........................................................................................7
Review the Packing Slip to Verify............................................................................................7
Check the unit for....................................................................................................................7
General Description.........................................................................................................8
Standard Specifications .................................................................................................9
The Wine Guardian Unit Contains ........................................................................................9
Accessories and Optional Equipment............................................................................10
Heating Coils ........................................................................................................................10
Water Cooled Option............................................................................................................10
Duct Collars and Flexible Ducts ............................................................................................10
Extended Compressor Warranty...........................................................................................10
Low Ambient Option..............................................................................................................10
Condensate Pump ................................................................................................................10
Humidifier and Humidistat .....................................................................................................10
High Ambient ........................................................................................................................10
Overview of the Wine Guardian Unit ...........................................................................11
Overview Illustration of the Wine Guardian Unit ....................................................................12
Overview Illustration of water-cooled system ........................................................................13
Wiring diagrams D025 and D050 ..........................................................................................14
Wiring diagrams D088 and D200 ..........................................................................................15
Wiring diagrams water-cooled D025 and D050 .....................................................................16
Wiring diagrams water-cooled D088 and D200.....................................................................17
Wine Guardian Dimensional Data .........................................................................................18
Wine Guardian Specifications sheet .....................................................................................19
Safety ............................................................................................................................20
Safety Message Conventions .............................................................................................20
Danger..................................................................................................................................20
Warning ................................................................................................................................20
Caution .................................................................................................................................20
Lockout/Tagout Procedure ..................................................................................................21
Safety Considerations...........................................................................................................21
Safety Hazards .....................................................................................................................21
Electrical Hazards.................................................................................................................21
Electrical Shock Hazards ......................................................................................................21
Hot Parts Hazards ................................................................................................................21
Moving Parts Hazards...........................................................................................................22
Equipment Safety Interlocks .................................................................................................22
Main Power Switch ...............................................................................................................22
Installation .....................................................................................................................24
Pre-installation Test ..............................................................................................................24
Air Flow Illustration................................................................................................................24

3
Planning the Installation.................................................................................................26
Addressing Items in the Planning Process ............................................................................26
Performing a Pre-installation Check......................................................................................26
Locating the Unit...................................................................................................................26
Grilles ...................................................................................................................................27
Reducing Noise from the Unit ...............................................................................................27
Installing the Unit Outdoors...................................................................................................27
Mounting the Unit ..........................................................................................................28
Floor Mounting......................................................................................................................28
Wall Mounting .......................................................................................................................28
Ceiling Mounting ...................................................................................................................28
Installing the Condensate Drain Connection .........................................................................28
Installing the Drain Line ........................................................................................................29
Priming the Drain Trap..........................................................................................................29
Wiring the Unit for Power...............................................................................................29
Installing the Thermostat and Communication Cable ....................................................31
Mounting the Remote Interface Controller.....................................................................31
Installation of the Wine Guardian Remote Sensor.........................................................33
Mounting the Remote Sensor ...............................................................................................33
Joining Communication Cable .......................................................................................35
Changing Jumper Positions ..................................................................................................35
Standard Controller Functions .......................................................................................36
Installing the Ductwork and Grilles ................................................................................41
Location of Supply and Return Grilles ...................................................................................41
General Duct Recommendation............................................................................................42
Using Ductwork.....................................................................................................................42
Cold Air to/from Wine Cellar..................................................................................................42
Warm Air to/from Condenser ................................................................................................42
Typical Mounting Arrangements ..................................................................................43
Duct Adapter Sizes........................................................................................................44
Ducting Options ...................................................................................................................44
Single Outlet Duct Installation .............................................................................................44
Inspection and Start-up Checklists ................................................................................45
Receiving and Inspecting ......................................................................................................45
Handling and Installing..........................................................................................................45
Starting-up the Unit...............................................................................................................45
Starting Up and Operating the Wine Guardian ..............................................................46
Turn on the Unit ....................................................................................................................46
Testing the Fan.....................................................................................................................46
Running the Unit ..................................................................................................................46
Cycling the Unit.....................................................................................................................47
Setting the Thermostat..........................................................................................................47
Regulating the Wine Cellar Temperature ..............................................................................47
Changing the Air Flow Direction............................................................................................47
Maintenance ..................................................................................................................48

4
General.................................................................................................................................48
Cleaning the Filters...............................................................................................................49
Cleaning the Condensate Drain System ...............................................................................49
Cleaning the Humidifier (optional) .........................................................................................49
Heating Coil Option...............................................................................................................49
Low Ambient Option..............................................................................................................50
Maintenance Schedule ................................................................................................50
Monthly .................................................................................................................................50
Yearly ...................................................................................................................................50
Troubleshooting ............................................................................................................51
Typical Start-up Problems ...................................................................................................51
Unit Does Not Start-up ........................................................................................................51
Power Switch Light is Off ......................................................................................................51
Power switch light is on and the thermostat light is off ..........................................................51
Power switch light is on and the thermostat light is on ..........................................................51
Unit is operating and blows evaporator air, ........................................................................52
Problems Controlling Cellar Temperature .............................................................................52
Cellar Temperature too cold (below 51°) when unit is running ..............................................52
Cellar Temperature is too cold (below 51°) when unit is not running .....................................52
Problems Controlling Cellar Humidity....................................................................................53
Humidity too low or supply air is too cold, without optional humidifier....................................53
Humidity too low, without optional humidifier.........................................................................53
Humidity too low with optional humidifier...............................................................................53
Humidity too high when unit is running but not cooling..........................................................53
Humidity too high when unit is not running............................................................................54
Humidity too high when unit is running and cooling...............................................................54
Other Miscellaneous Problems .............................................................................................54
Unit operates but the power switch light is not ON ................................................................54
Unit is leaking water..............................................................................................................54
Unit is running properly, but the sound of the unit is objectionable ........................................54
High Pressure Switch has Shut Down the Unit ..........................................................55
Instructions to Reset High Pressure Switch .......................................................................55
Advanced Troubleshooting ............................................................................................56
Evaporator coil is freezing.....................................................................................................56
High pressure switch keeps tripping......................................................................................56
Unit cycles on and off more than 8 times/hr ..........................................................................56
High pitched or loud rubbing noise, clanking or vibration ......................................................56
Replacing the blowers...........................................................................................................56
Contact and Warranty Information.................................................................................57
Contact Information...............................................................................................................57
Warranty and Warranty Procedure .....................................................................................57

5
Directory of Terms
Ambient Air –The surrounding area outside the cellar such as a room, basement, garage or
outdoors.
CFM –Cubic feet per minute. A unit of measurement for the amount of air handled by the fan.
Condensate / Condensation –The water formed out of the air when it is cooled below a certain
temperature (called dew point). Often referred to as “sweating” on pipes and cold surfaces. This
water collects at the bottom of the evaporator or cooling coil and drains out of the unit through the
drain line.
Condenser (Heat Rejection) Section / Coil –The Condenser Section uses the compressor,
condenser coil and fan to remove heat from the refrigerant to the ambient air outside the wine cellar.
The word condenser refers to the condensation of the refrigerant from gas to liquid phase.
CSA/ETL –Canadian Standard Association/Electric Testing Laboratory
Exhaust Air –The air leaving the evaporator or condenser section of the Wine Guardian unit.
Evaporator (Cooling) Section / Coil –The Evaporator Section uses the cooling coil and the fan to
remove heat from the air inside the wine cellar to the refrigerant, cooling the air and condensing
moisture out of the air. The word evaporator refers to the evaporation of the refrigerant from liquid
to gas phase in the coil. The Evaporator Section is connected to or inside the wine cellar.
Flexible Duct –Round ducts with steel reinforced plastic liners, a layer of insulation and an
outer plastic layer used to convey the air from the unit to the cellar or ambient space.
Grille or Diffuser –Inlet or outlet plates to direct the airflow or protect the inside of the unit.
Heat Gain / Loss –The amount of cooling or heating expressed in watts transferred between
the wine cellar and the ambient space. The Wine Guardian must offset this load.
Inlet Air –The air entering the evaporator and condenser sections of the Wine
Guardian unit.
Inlet Air –The air returning from the wine room to the Wine Guardian fan coil.
I.D. –Inside diameter
NEC –National Electrical Code
O.D. –Outside diameter
Psig Pounds –Force per square inch gauge
NEC –National Electrical Code
Recovery –The amount of cooling the unit does to return the cellar to its set point temperature
after some new load is introduced, such as people or new cases of warm wine entering the cellar.
Return Air - The air leaving the cellar and returning to the inlet of the evaporator coil.
SP –Static pressure. Unit of measurement (inches of water column) of the pressure of the air
handled by the fan.
Set Point –The desired temperature or humidity set on the thermostat or humidistat.
Supply Air - The air entering the cellar from the discharge of the evaporator coil.

6
Illustrations
Overview of the Wine Guardian unit.................................................................................12
Overview –vapor compression system .............................................................................12
Overview –water-cooled system.......................................................................................13
Overview –vapor compression system .............................................................................13
Wiring diagram of D025 and D050 ...................................................................................14
Wiring diagram of D088 and D200 ...................................................................................15
Wiring diagram of water-cooled D025 and D050 .............................................................16
Wiring diagram of water-cooled D088 and D200 .............................................................17
Wine Guardian dimensional data.......................................................................................18
Wine Guardian specifications sheet...................................................................................19
Airflow illustration.............................................................................................................24

7
Receiving, Inspecting and Unpacking the Wine Guardian Unit
Receiving and Inspecting the Unit
NOTE: Wine Guardian units are factory assembled and tested prior to shipment.
Wine Guardian units are shipped in individual corrugated boxes.
Lift at the designated handhold locations only or fully support from underneath. A
shipment may include one or more boxes containing accessories.
Before opening the container, inspect the packing crates or boxes for obvious signs of
damage or mishandling.
Write any discrepancy or visual damage on the bill of lading before signing.
Inspect all equipment for any sign of damage caused during transit.
Report all visual or concealed damage to the carrier and file a claim immediately.
Thoroughly inspect the contents for any visible damage or loose parts.
Review the Packing Slip to Verify
Model number
Factory installed options
Unit accessories
If any items listed on the packing slip do not match your order information, contact the place of
purchase immediately.
Check the unit for
An electrical power cord
A thermostat with communications cable plugged into side of unit
A drain line coming out of the unit
IMPORTANT
If this procedure is not followed, the shipping company may reject the claim and
the consignee may suffer the loss. Do not return the shipment to the factory.

8
General Description
Refer to overview illustrations starting on page 12
The Wine Guardian cooling unit is a professional grade, American manufactured, self-contained
climate control unit designed specifically for the storage of wine at cellar temperatures. It is
designed for easy installation and operation. Wine Guardian uses digital electronic controls and
R-134a refrigerant. The entire unit is tested at the factory and shipped as a single package. All
components are of a high quality, standard commercial grade. The entire unit is approved by ETL
according to UL 1995 and CSA safety standards. All wiring complies with NEC. Each unit is
furnished with a sealed, UL-approved power cord and plug.
The Wine Guardian unit is completely self-contained and includes either an integral air cooled or
water-cooled condenser. The unit is functionally divided into two sections, the evaporator (or
cooling section) and the condenser (or heat rejection section). Each section contains a coil to add
or remove heat and a fan to move the air through the coil and into or out of the cellar or adjacent
space. The Wine Guardian unit is designed to be used as a remotely mounted unit with external
ductwork connections.
Air first passes through the cooling coil and is cooled by the refrigerant inside the coil. This
causes any excess humidity in the air to condense and be captured in the drain pan and piped
outside the unit. Air then enters the fan where it is pressurized and discharged out of the unit.
Optional heating coils are located between the cooling coil and the fan. These coils heat the air
to prevent low temperatures in the cellar. The thermostat, located in the cellar, turns on the
cooling or heating as needed to maintain its setpoint. It does not allow the cooling and heating to
be on at the same time.
The compressor and condenser sections are activated whenever the unit is cooling. The condenser
fan draws air from the surrounding or ambient space either directly or through a duct. The air is
first drawn through a filter to remove any airborne dust particles to keep the coil clean. The air
flows through the condenser coil where it absorbs heat from the refrigerant in the coil. The air is
then discharged out of the unit by the condenser fan.
The water-cooled Wine Guardian system requires cooling water to be piped to the unit for proper
operation. The cooling water absorbs the refrigerant heat through the unit’s water-cooled
condenser coil. Warm water is then directed out of the unit back to the cooling water system or to
a drain.
IMPORTANT
The air exhaust from the condenser fan on air-cooled units is hot and will be 25 to 35 degrees F
above the entering temperature. This may cause overheating problems in the summer months,
especially with high humidity. Exhaust the hot air to the outside. In the winter, this heated air
can help to heat the surrounding space.

9
Standard Specifications
The Wine Guardian Unit Contains
A thermal expansion valve to control the flow of refrigerant into the evaporator coil
A filter dryer to keep the refrigerant clean and free of contaminants
A sight glass to observe the level of refrigerant
A manual reset high pressure switch to protect the system from high pressures
The unit uses only R-134a refrigerant
A built-in condensate drain trap. (no external trap is required)
The Wine Guardian meets or exceeds its rated capacities for total BTU/H and CFM at design cellar
conditions and external static pressures. Both the evaporator and condenser fans are capable of rated
CFM against the external static pressure imposed by recommended ductwork. Both fans are
motorized impeller plug fans, statically and dynamically balanced, and use permanently lubricated,
direct drive motors that require no maintenance.
All exterior framing of the Wine Guardian is powder coated 0.063” gauge aluminum to prevent rust
and corrosion. All coils are copper tubes with aluminum fins. The unit uses an external drain to
remove excess moisture and not reintroduce it into the cellar or ambient space. Removable, multiple
access doors are provided to facilitate cleaning and maintenance, duct connections, and access to
components and wiring.
The condenser coils have pre-filters on the inlet to prevent dust and dirt from fouling the coils,
thereby reducing capacity. Each unit has at least three discharge outlets on both the evaporator and
the condenser coils to facilitate custom installations. Water-cooled units have copper straight tube
connections for both cooling water inlet and outlet.
Each unit is provided with a pre-wired and tested electronic digital thermostat for remote mounting
in the cellar. The thermostat has multiple control functions for the fans, cooling and heating. It has a
fully automatic mode to switch between heating and cooling.
Compressors are rotary, self-lubricating, permanently sealed, hermetic reciprocating type compres-
sors, with internal overload protection and capacitor start with a minimum of one-year
manufacturer’s warranty and an optional five-year warranty. Compressors are mounted on rubber-in-
shear isolators to reduce noise and vibration.
Electric power is supplied by a single factory furnished cord and plug. All external controls are
digital and proprietary to Wine Guardian products. Only approved communication cable and Wine
Guardian controllers are suitable for proper system operation.
IMPORTANT
Design and specifications are subject to change without notice

10
Accessories and Optional Equipment
Heating Coils
An optional heating coil is built-in and requires no additional power source. The electric heating
option is factory installed and includes primary and secondary over-temperature protection devices
per UL and NEC.
Water Cooled Option
A water cooled option is available that uses a tube-in-tube heat exchanger in place of the
condenser coil and fan. Waste heat from the refrigerant is transferred to the water. A two-way
control valve is used to regulate the flow of water to maintain head pressure.
Duct Collars and Flexible Ducts
Ducting for the Wine Guardian is sold in kits by size for each unit. Each kit contains two adapter
collars, one 25-foot length of round flexible duct and two straps. The number of duct kits needed
depends on the layout. The size of the kit depends on the model Wine Guardian selected. Follow
installation instructions carefully. Poorly or incorrectly installed ducts can degrade the performance
of your unit dramatically.
Extended Compressor Warranty
The Wine Guardian uses only the best commercially available compressors on the market. However,
since the compressor is the single most expensive component in the unit, it is recommended that you
purchase the extended warranty option.
Low Ambient Option
A factory installed Low Ambient option is available that makes the Wine Guardian capable of
exposure to low ambient temperatures. This feature controls the condenser fan operation based on
head pressure and heats the oil reservoir. The Low Ambient Option (LAO) is recommended
whenever the condenser section is exposed to air temperatures below 40 degrees F. This can occur
if the unit is placed in a garage or under an outdoor canopy, or if the unit is located inside a heated
space but the condenser air is ducted in from the outside.
Condensate Pump
An optional Wine Guardian automatic condensate pump is available to pump the water to a sink or
outside. It requires a separate 120 volt electrical outlet.
Humidifier and Humidistat
Another popular option for the Wine Guardian is a humidifier. The humidifier is available as a
freestanding unit powered by the Wine Guardian system, as freestanding unit with its own power
cord and humidistat or as an integrated unit that bolts to the side of any Wine Guardian ducted
system. The Wine Guardian humidifier requires a water supply and drain for operation.
CAUTION
CAREFULLY FOLLOW THE INSTALLATIONS INSTRUCTIONS INCLUDED WITH THE HUMIDIFIER.
REFER TO THE INSTRUCTIONS CONTAINED IN THE BOX FOR THE HUMIDISTAT.
High Ambient
A factory installed high ambient option is available (on D025 and D050 models only) that makes the
Wine Guardian capable of exposure to high ambient temperatures. The high ambient feature consists
of high output, fan condenser, and fan and coil. The high ambient option is recommended whenever
the condenser section is exposed to air temperatures above 100 degrees F to a maximum of 120
degrees F.

11
Overview of the Wine Guardian Unit
Refer to overview illustrations starting on page 12
Cabinet – The cabinet and access doors are constructed of aluminum with a powder coated finish for
corrosion protection and an attractive, maintenance-free appearance. Areas in contact with cold
temperatures are lined with insulation to prevent condensation
.
Condensing Section – Ambient air is circulated through the condenser section by a direct drive,
permanently lubricated, motorized impeller blower. This section also contains the compressor and the
electrical controls. If the water cooled option is purchased, a heat exchanger is used in place of the
condenser coil and blower.
Evaporator Section
– Cellar air is circulated through the evaporator section by another blower the
same as above. The large evaporator coil face area eliminates condensate carry-over, reduces air
pressure drop and optimizes heat transfer. A drain pan is located directly below the coil to capture
condensate and is fabricated from aluminum to prevent rust and corrosion. The electric heating coil, if
ordered, is factory installed between the evaporator coil and the blower, and is complete with
contactor(s) and limit controls.
Electrical Controls
– Most of the electrical components and controls are located in a separate area
accessible on the side of the unit. All wiring is in accordance with the NEC. Wires are numbered and
color coded to match the wiring diagrams.
Factory Tested
– All Wine Guardian units are factory run-tested and checked for operational
performance.
Filters
–Nominal 1 inch thick filters are provided on both the evaporator and condenser inlets to
protect the coils from dust and dirt. These filters are washable and reusable.
Humidity Option
– The optional humidifier comes fully assembled and tested for field installation
onto the Wine Guardian without any additional electrical power wiring. It automatically adds
moisture into the cellar by the evaporation of water over a distribution pad. The same Wine Guardian
thermostat controller supplied with the Wine Guardian unit automatically controls humidity as well as
temperature.
Internal Drain Trap - Water condensate from the evaporator coil fills the trap and forms a seal to
prevent air from being drawn back through the drain tube. This allows the drain pan to drain freely.
No external trap is required.
Refrigerant Circuit
–The factory charged circuit includes a thermal expansion valve with an
external equalizer, sight glass with moisture indicator, a filter dryer, an automatic low pressure
switch, and a manual reset high pressure switch. For the low ambient option, an automatic pressure
switch controls the operation of the condenser blower and a heating element is added to the compres-
sor oil reservoir. See Fig 1 - Refrigeration Illustration on next page.
Supply/return grilles
–A p owder-coated steel single direction grille is provided on the outlet of
condenser section. One grille is provided on an outlet. The grille is interchangeable with access doors
to control and direct the airflow. These grilles may be used in the room on the end of the ducts in
ducted systems.

12
Overview Illustration of the Wine Guardian Unit
Fig. 1
Fig. 2

13
Overview Illustration of water-cooled system
Fig. 3
Fig. 4

14
Wiring diagrams D025 and D050
Fig.5

15
Wiring diagram D088 and D200
Fig.6

16
Wiring diagram water-cooled D025 and D050
Fig.7

17
Wiring diagram water-cooled D088 and D200
Fig. 8

18
Wine Guardian dimensional data
Fig. 9
Table 1
Wine Guardian Dimensional Data
Model Number
24S025
24S050
24S088
24S200
Dimensions - Nominal - add 0.375" for each grille
A –Width
Inches
14
22
22
22.38
B –Height
Inches
14
14
14
18
C –Length
Inches
32.63
32.63
32.63
49.50
D –Evap. discharge location
Inches
23.38
23.38
23.38
37.19
E –Cond. discharge location
Inches
9.25
9.25
9.25
12.31
F –Inlet opening width
Inches
10
10
10
18.88
G –Drain outlet location
Inches
16.31
16.31
16.31
28.75
H –Discharge opening width
Inches
10
10
10
11.63
I –Inlet opening Height
Inches
12
12
12
15
J –Duct opening
Inches
8
10
10
12
AA –Water out (O.D)
Inches
0.625
0.625
0.625
0.625
BB –Water in (O.D)
Inches
0.625
0.625
0.625
0.625
Weight
lbs
80
125
130
200

Model Number D025 D050 D088 D200
Performance
Nominal Compressor HP .33 .50 12.5
Net Cooling Capacity*
@ 70 Deg F Ambient
BTUH 3300 / 3650 5600 / 6050 8400 / 9100 16200 / 17750
@ 80 Deg F Ambient BTUH 3000 / 3300 5300 / 5700 7800 / 8450 15200 / 16550
@ 90 Deg F Ambient BTUH 2800 / 3050 4850 / 5275 7300 / 7900 14100 / 15350
Controls
Type Room mounted non-programmable thermostat
Accuracy ± 2°F
Evaporator Section
Fan Motor Size Watts 75 100 195 240
Rated Air Flow CFM 235 430 510 870
Air Flow with 25' flex duct CFM 207 400 485 (*4.*) 740
Air-cooled Condenser Section
Fan Size Watts 75 100 195 240
Rated Air Flow CFM 253 400 500 870
Air Flow with 25' flex duct CFM 220 365 475 (*4*) 740
Water-cooled condenser Section (option)
Water usage at 40 Deg F rise GPM 0.30 0.60 1.20 2.50
Pressure drop PSI 0.40 0.40 0.85 1.20
Pipe connection size (in/out) O.D. Inches 0.63 0.63 0.63 0.63
Heat
Type Integral electric heater coil
Capacity Watt/btuh 1000/3413 1000/3413 2000/6826 2000/6826
Temperature rise -including fan Deg F 13.5 8.6 12.0 8.1
Humidifier
Type Removable Drip pad with integral fan
Supply water temp of 60 Deg F gal./day 1.6
Supply water temp of 90 Deg F gal./day 3.5
Supply water temp of 120 Deg F gal./day 5.1
Control Cellar mounted digital humidistat
Electrical Requirements
Power Requirements V/P/H 115/1/60 115/1/60 230/1/60 230/1/60
Current Draw -Cooling mode Amps 8.6 11.9 9.0 16
Current Draw -Heating mode Amps 9.4 9.6 9.6 10
Minimum Circuit Size Amps 15 15 15 20
Optional Low Ambient Amps 0.4 0.4 0.2 0.2
Optional Humidifier Amps 0.3 0.3 0.2 0.2
7000 Performance Drive | North Syracuse, New York 13212 USA
800-825-3268 | 315-452-7400 | Fax [phone] | www.wineguardian.com |
[e-mail]
1. Net cooling capacity at entering temperature and humidity conditions of 55 Deg F and 60% RH / 60 Deg F and
60% RH and at rated airflow. Reduce capacity by 3%for each 10% reduction in either condenser or evaporator
airflow, 5% for both.
2. Wine Guardian reserves the right to make changes to this document without prior notice at its sole discretion.
3. All ratings at sea level.
4. D200 air flow based on 0.35 inches Wine Guardian external static pressure using 50’ of flexible ductwork, grilles
and collars . Rev. 3/2012

20
Safety
Before installing or maintaining the Wine Guardian unit do the following:
1.
Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions .
Safety Message Conventions
Safety messages contained in this manual, DANGER, WARNING, and CAUTION are bold and
highlighted in red for quick identification.
Danger
A Danger message indicates an imminently hazardous situation which, if not avoided, results in
death or serious injury. Messages identified by the word DANGER are used sparingly and only
for those situations presenting the most serious hazards.
Following is a typical example of a Danger message as it could appear in the manual
DANGER
HIGH VOLTAGE - RISK OF SERIOUS INJURY OR DEATH
High voltages are present in the cabinets.
Before opening panels turn off all power.
Use the Lockout/Tagout procedure.
Warning
A Warning message indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
Following is a typical example of a Warning message as it could appear in the manual
:
WARNING
RISK OF PERSONAL INJURY OR DAMAGE TO EQUIPMENT
Modification to the equipment may cause injury.
Caution
A Caution message indicates a potentially hazardous situation which, if not avoided, could result
in minor or moderate injury. It may also be used to alert against unsafe practice
IMPORTANT
The equipment described in this manual uses electricity. Be sure to follow the safety
procedures outlined in the Wine Guardian Manual.