Winners Only D3-M172R User manual

Assembly Instruction
for
Revised 2008.11.13
D3-M172R

A
BCD
E
H
I
J
K
A
B
C
D
E
Components List
Main Pedestal
Main Centre Back Panel
Main RHF Back Panel
Main RHF Side Panel
Main RHF Small Panel
Main RHF Glide Assembly
Main Drawer Support
Main Drawer
Main Top
Triangular Shelf
Return Pedestal
Return Back Panel
Return Small Panel
Return Keyboard Support
Return Keyboard Tray
Return Top
Parts List
Place [Main Pedestal] (A) on
a flat surface, Using 3
machine screws (5), secure
[Main Centre Back Panel] (B)
to the back of [Main Pedestal]
(A).
A
B
Insert the other end of (G) into the square hole of [Main
RHF Glide Assembly] (F). Secure [Triangular Shelf] (P)
using 4 [Machine Screws] (5).
L
M
(1) Figure-8 Irons: 24
(2) Long (1¼“) Flat Head
Wood Screws : 27
(4) Wood Dowels
(5/16 x 1"): 6
(5) Machine Screws
(1¼“): 28
(6) Pan Head Wood
Screws (1¼“): 4
(7) Long Machine
Screws (1¾“): 1
Other Parts (photo not shown)
(9) Metal Grommets: 1
(10) Keys for File Drawer: 2
(11) Power Centre: 1
F
G
N
O
(8) Short Machine
Screws (1"): 1
H
I
J
K
L
N
O
CUsing 3 machine screws (5),
attach [Main RHF Back
Panel] (C) to [Main Centre
Back Panel] (B).
B
Using 6 machine
screws (5) to loosely
secure (D) to (C)
and to attache (E) to
(D). Place (G) into
the square hole on
(A).
D
E
C
G
A
F
G
Use Short Machine Screw (8) to secure (F) to (E)
through the hole indicated by the arrow above. Fasten
(G) to (A)/(F) with 2 (6) Pan Head Wood Screws. Now
tighten the machine screws holding (C) and (D).
E
F
G
(3) Short (¾”) Flat Head
Wood Screws: 24
P
P
P
(8)

Place [Return Pedestal] (J) on
a flat surface, Using 3
machine screws (5), secure
[Return Back Panel] (K) to the
back of [Return Pedestal] (J).
J
J
K
Using 3 machine screws (5), attach [Return Small
Panel] (L) to [Return Back Panel] (K). Do not tighten the
machine screws yet.
K
J
L
L
M
J
K
Insert [Return Keyboard Support] (M) into the square
holes on (L) and (J). Fasten (M) using 2 [Pan Head
Wood Screws] (6).
Extend the keyboard metal glides. Insert [Return Key-
board Tray] (N) into the metal glides.
N
Place Main Desk and Return side by side. Secure the
two together using 1 [Long Machine Screw] (7) and 3
[Machine Screw] (5), through the holes indicated by
arrows below. Insert [Main Drawer] (H) into the metal
glides found on the sides of (A) and (F).
(5) x 3
(7)
A
F
L
E

Put 1 [Long (1¼“) Flat Head Wood Screws] (2) through
the larger hole of each [Figure-8 Iron] (1). Fasten each
[Figure-8 Iron] to one of the 24 round depressions on the
top edge of desk. Insert and tap in [Wood Dowels] (4)
into each of six 5/6" holes. The main desk has 15 round
depressions and 4 dowel holes; the return has 9 round
depressions and 2 dowel holes.
Take note of the position of the extra wood connector on
the top of [Main RHF Glide Assembly] (F). You will need
it in later steps.
Look under the overhang of the desk, including kneehole.
There should be 24 half-exposed [Figure-8 Irons] (1).
Use [Short (¾”) Flat Head Wood Screws] (3) to secure
the bases to the tops. Do not use anything longer than
the short wood screws provided. Longer screws may
penetrate the tops and cause irreparable damages.
In addition, use the remaining 3 [Machine Screws] (5) to
fasten [Main Desktop] (I) through the extra wood connec-
tor (found on the top of (F) and noted earlier).
Similarly, use 3 [Long (1¼“) Flat Head Wood Screws] (2)
to fasten top (I) through the extra wood connector found
on top of (D).
The desk is now fully assembled. When moving the
desk, please remove the 4 [Machine Screws] (7) and (5)
holding (E) & (L) so that the desk can be handled as 2
parts.
F
H
I
O
Place [Main Top] (I) and [Return Top] (O) on their respec-
tive bases. Take care to align pre-drilled holes on the
underside of tops and the wood dowels inserted earlier.