Winners Only GC266R User manual

Notes: Need two people to assemble.
1
1
2
1
1
1
1
Instructions:
Chart 1
Step 1. Align the R1B pedestal (A) & back panel extension (F) to the back panel (E), insert
and tighten with 1-1/4" machine bolts (6PCS).
Chart 2
Step 2. Align the RSF side panel (G) to the back panel extension (F) and the L-shaped RHS
panel (I) to the RSF side panel (G), insert and tighten with 1-1/4" machine bolts
(6PCS).
2
2
2
2
2

5
5
5
5
6
6
6
3
4
78
1-1/4"
7
8
9
8
7
3
2
X4
X4
X12
X12 X3 X2
X1
Chart 3
Step 3. Use 1-1/4" machine bolts (4PCS) to connect RHS glide panel (D) to L-shaped RHS
panel (I) and back panel (E).
Step 4. Using a Mallet, carefully insert Cross Bar (H) to the R1B pedestal (A) and RHS glide
panel (D), tighten with 1-1/4" flat head wood screws (2 PCS) to Cross Bar (H) from
R1B pedestal (A) side and from RHS glide panel (D) side.
Step 5. Hammer the wood dowels (4 PCS) on the R1B pedestal (A) and RSF side panel (G).
Step 6. Loosen the screw to adjust metal figure 8 (12 PCS) of its direction of the panel and
re-screw.
H
DI
G
Chart 4
Step 7. Insert short (1") flat head wood screws (12 PCS) through metal figure 8 to connect
R1 desk top (B) and base.
Step 8. Use 1-1/4" machine bolts (3 PCS) and (1-1/4") flat head wood screws (2pcs) to
connect the RHS glide panel (D) and R1 desk top (B).
Step 9. Use long(1-1/4")flat head wood screws (2 PCS) to connect Cross Bar (H) to R1
desk top (B). Main Desk completely assembled
DHD
4
X1
3
Remove strap
8X2
4

10
11
11
Chart 5
Step 10. Align the R2B pedestal (K) & L-shaped LHS panel (O) to the back panel (N),insert
and tighten with 1-1/4" machine bolts (6PCS).
Step 11. Using a Mallet, carefully insert Cross Bar (M) to the L-shaped LHS panel (O) and
R2B pedestal (K), tighten with 1-1/4" flat head wood screws (2 PCS).
10
10
10
10
10
Chart 6
Step 12. Assemble the Return Desk to the Main Desk by using four 1-1/4" machine bolts
(4PCS) to attach connecting board.
12
12
12
12
X4 RETURN DESKMAIN DESK
11

ball bearing
retainer
17
MAIN DESK
RETURN DESK
16
Chart 8
Step 16. Insert the two Grommets on top of the Main Desk and Return Desk.
Step 17. Install the drop front center drawer (C) and keyboard pullout (L) to place.
Important:
(Be sure to move the ball bearing retainer all the way to the front of the glide
and carefully slide the rails into the glides and ball bearing retainer.)
Assembly is now complete
CL
13
14
14 13
15
15
Return Desk completely assembled
Chart 7
Step 13. Hammer the wood dowels (2 PCS) on the R2B pedestal (K) .
Step 14. Loosen the screw to adjust metal figure 8 (8 PCS) of its direction of the panel and
re-screw.
Step 15. Insert short (1") flat head wood screws (8 PCS) through metal figure 8 to
connect R2 desk top (J) and base.
Remove strap