Wirquin 20980001 User manual

HINGE FITTING INSTRUCTIONS 270913
B_06/2021
Stainless steel soft close hinges
BEFORE INSTALLING YOUR WIRQUIN TOILET SEAT
•Verify the colour and size.
•Check that the visual surface is free from cracks and surface defects.
•Ensure that all components are present and in a satisfactory condition.
•No claims will be entertained after installation.
ONLY SUPPLIED WITH SELECTED COMPATIBLE SEATS. Ignore this step if not included.
1
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
2
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
3
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
4
 holds the seat in place!
STOP SEAT
MOVEMENT
A : INSTALLATION OF FIXATION TO PAN
FAST
SLOW SLOW SLOW SLOW
A
B
x1
x1
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
B : INSTALLATION OF SOFT CLOSE CARTRIDGES
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
•Ensure the seat and lid are clean from any debris.
•Unscrew the fastener on the cartridges by hand with minimum
force to a maximum of 2mm to OPEN position.
•Align cartridges and insert into seat.
•A- Controls speed of LID. B- Controls speed of SEAT
•CLOSED position •OPEN position
•DO NOT unscrew the fastener with the allen key.
•DO NOT force fastener beyond mechanical stop.
•DO NOT attempt to unscrew the fastener completely.
•THE ABOVE WILL CAUSE IRREPAIRABLE DAMAGE TO THE SCREW
THREAD AND RENDER THE HINGES USELESS!
2mm
5 6
1h30 1h00 30 mn 15 mn 10 mn
1 2 3
click !

HINGE FITTING INSTRUCTIONS 270913
B_06/2021
Stainless steel soft close hinges
www.wirquin.co.za
WIRQUIN Manufacturing | 1 Hospital Road - Somerset East | Eastern Cape - 5850
T: [phone] | Email: [email protected].za
CARE AND CLEANING INSTRUCTIONS
•The seat and cover should be cleaned using warm soapy water.
•Do NOT use aggressive or abrasive cleaners as this may scratch the surface.
•The hinges should be cleaned using soap or mild detergent.
•After cleaning, the hinges should be rinsed in clean water and dried.
•NEVER use bleach, concentrated cleaners or acids as this will cause discolouring
and pitting.
•Do not leave bleach in the toilet bowl with the cover closed because it may
cause discolouration of the seat and hinges.
•The cover of the toilet seat is for decorative purposes only. The lid is not
guaranteed to carry weight.
(Do NOT stand or sit on the cover.)
FAST
SLOW SLOW SLOW SLOW
A
B
x1
x1
•Place seat onto fixation to align before placing covers over.
•Align seat in position and remove seat to tighten fixation with a
screwdriver.
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
FAST
SLOW SLOW SLOW SLOW
A
B
x1
x1
•Once fixation is tight, place covers over.
•Place seat onto fixation.
•Tighten fastener with alan key supplied.
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
FAST
SLOW
SLOW
SLOW
SLOW
A
B
x1
x1
•Adjust speed of seat and lid independantly as shown below.
B : INSTALLATION OF SOFT CLOSE CARTRIDGES C : ADJUSTING THE SPEED OF SOFT CLOSE
7
8
9
10
11
SCAN THE QR TO VIEW THE HINGE
ON OUR WEBSITE WITH DETAILED
VIDEO’S ON SETTING THE HINGES