WisyCom MTP61 Instruction manual

QUICK USER GUIDEQUICK USER GUIDE
Main Accesories (nd more information at Wisycom.com )
LBC61: Multiple battery charger (4 MTP61
+ 4 batteries) + TX management + LTC
CAUSBM5P: Cable from USB/A to mag-
netic connector 5pin-M, lenght=1050mm
for battery charging, TX management and LTC
T i m e c o d e s y n c
LBP61: rechargeable Lithium-ion battery
Model CS-BCE10, Cameron Sino Part No.
CGA-S008E. 3.7V, 1050 mAh, 3.9Wh
LBP61: rechargeable Lithium-ion battery
Model CS-BCE10, Part No. CGA-S008E
3.7V, 1050 mAh, 3.9Wh, Cameron Sino
BCL61: spring loaded belt clip
BCLW61: reversible wire belt clip
MTP61-en-q03#ISTR-MTP61
(*)The Wisycom microphone pocket transmitter model MTP61 complies with the following requirements: FCC (Federal Communications Commission) Part 74.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operations. Changes or modication not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. FCC ID can be found inside the battery compartment.
This device complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.Note: the grantee is not responsible for any
changes or modications not expressly approved by the party responsible for compliance. such modications could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
(**) EN This device complies with Industry Canada license-exempt RSS-123 and RSS-210 standard. Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter IC: 11967A-MTP61 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible
gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
FR Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence RSS-123 et RSS-210. L’exploitation
est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Le présent émetteur radio IC: 11967A-MTP61a été approuvé
par Industrie Canada pour fonctionner avec les types d’antenne é numérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour
chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l’exploitation de l’émetteur.
Antenna types (50 Ohm impedance, max gain 2.1dBi): AWSS-507: band 470-547 MHz, AWSS-590: band 547-663 MHz, AWSS30-950: band 940-960 MHz.
This equipment complies has been evaluated for and shown compliant with the FCC and ISED RF Exposure limits. The unit of measurement for RF exposure
is Specic Absorption Rate (SAR). The FCC SAR limits for is 1.6W/Kg per 1g of tissue
The maximum SAR levels tested has been shown to be 0.85 W/kg at head with 0mm of separation distance from the body.
This device operates on a no-interference, no-protection basis. Should the user seek to obtain protection from other radio services operating in the same TV
bands, a radio license is required. For further details, consult Innovation, Science and Economic development Canada’s Client Procedures Circular CPC-2-1-
28, Voluntary Licensing of License-Exempt Wireless Microphones in TV Bands.
MTP61MTP61
This guide is intended to assist you with initial quick setup and
operation of your Wisycom product.
You can refer to Wisycom Autorized Distributors for technical
Support and information about service and repairs available in your
area or contact us directly by email.
Serial Number: Purchase Date:
Download Documentation and Firmware
Get declarations, user manual, specica-
tions and softwares on the download page:
wisycom.com/products/d/MTP61
Keep up with Wisycom online
Follow us on Facebook and Instagram. You
can also subscribe on Youtube for more.
wisycom.com/social
Product Registration and Warranty
Register your product to extend your warranty
and receive update on latest rmware:
wisycom.com/registration
Conformity
RADIO Directive 2014/53/
EU Radio Equipment
Directive (RED)
FCC-ID: POUMTP61 *
UK Conformity IC: 11967A-MTP61 **
IC
WISYCOM S.r.l.
Via Tiepolo 7/E
35019 Tombolo (PD) - ITALY
WISYCOM INC.
14301 Sullyeld Circle, Suite C
Chantilly, VA 20151- USA
[phone]
[email protected]
[email protected]
[email protected]
[email protected]
[phone]
conformity identication is visible on the display by accessing from the Main menu the Info> STD submenus:
step 1: access submenu Info; step 2: access submenu STD.

Antenna Connector (SSMA type).
SEL / ON
Push to switch ON the device. Push together with
GAIN/UP to enter the main MENU. When in menu
single push to save and conrm selections.
EXIT / OFF
Long press to switch the unit OFF.
Short press to step back in menu
Press together with SEL/ON to mute/
unmute the audio.
Ch Shortcut/Down
Short press to access channel/group/
frequency menu and/or scroll down while in
the menu. Long press it with EXIT/OFF to
lock the front panel.
Gain Shortcut/Up
Push to quickly access gain setup frequency
menu and/or scroll up while in the menu.
Recording Status Led
Solid red when recording has started.
Battery compartment
Press to
open
Mic Input (LEMO type)
Load a mic PRESET to suit your
wiring or enter the Audio menu.
Transmitter name
Frequency
Group
Channel Audio bar
Tx PWR status
Battery
status
Panel
locked
RF level
in mW
Bluetooth
Recording ON
Label Code Band MHz
Antenna type
507 AWSS-507 470-547
590 AWSS-590 547-663
552 AWSS-552 510-595
646 AWSS-646 595-698
710 AWSS-710 663-760
796 AWSS-796 760-832
808 AWSS-808 806-810
950 AWSS-950 940-960
1K1 AWSS-1K1 960-1160
1K2 AWSS-1K2 1240-1260
Mic Mode Pinout
2 W 1 = GND / 3 = AF
2 W+B 1 = GND / 3 = AF+5,5 V
3 W 1 = GND / 2 = 5,5 V / 3 = AF
AUX 1 = GND / 3 = AF (High impedance)
Magnetic Connector 5 pin
to recharge battery, connect to Wisycom
Manager, LTC Timecode sync, Download
recorded les (USB High Speed).
OFF: Audio is muted
GREEN: Audio is enabled
RED: Audio is peaking
OFF: MTP61 is OFF
GREEN: Transmission is ON
RED: Transmission is OFF
RED SLOW BLINK: battery < 25%
RED FAST BLINK: battery < 12%
Audio LED RF/Power LED