Wittenstein Alpha LUC+125 User manual

1000088470 Revision: 01
Lubricator
LUC
+125, battery version, time-controlled
Operating manual

LUC+125, battery, time-controlled
1000088470 Revision: 01
Sales department
WITTENSTEIN alpha GmbH
Walter
-Wittenstein-Straße 1
D
-97999 Igersheim
Germany
Customer Service department
In the event of technical
questions, contact the following address:
Copyright
© WITTENSTEIN alpha GmbH 2022
reserves all rights for layout and corporate design.
© DLS Schmiersysteme GmbH 2022
reserves all rights for content and text.
This documentation is protected by copyright.
WITTENSTEIN alpha GmbH
and DLS Schmiersysteme GmbH reserve all rights to photo-
mech
anical reproduction, copying, and the distribution by special processes (such as computers,
file media, data networks), in whole or in part.
Subject to technical and content changes without notice.

LUC+125, battery, time-controlled
Revision: 01 1000088470 en-1
Table of contents
1About this manual .............................................................................................................................3
1.1 Information symbols and cross references...................................................................................3
1.2 Scope of delivery..........................................................................................................................3
2Safety..................................................................................................................................................3
2.1 EC/EU Directive............................................................................................................................3
2.2 Personnel .....................................................................................................................................3
2.3 Intended use.................................................................................................................................4
2.4 Reasonably foreseeable misuse ..................................................................................................4
2.5 Guarantee and liability..................................................................................................................4
2.6 General safety instructions...........................................................................................................5
2.7 Structure of warning instructions..................................................................................................5
2.7.1 Safety symbols......................................................................................................................5
2.7.2 Signal words..........................................................................................................................6
3Description of the lubricator.............................................................................................................7
3.1 Overview of lubricator components ..............................................................................................7
3.2 Name plate and labeling...............................................................................................................7
3.3 Marking.........................................................................................................................................8
3.4 Ordering codes.............................................................................................................................8
3.5 Dimensions...................................................................................................................................8
3.6 Scope of delivery..........................................................................................................................8
3.7 Technical data..............................................................................................................................9
3.8 Lubricants...................................................................................................................................10
3.9 Cord lengths...............................................................................................................................10
4Transport and storage.....................................................................................................................10
4.1 Transport....................................................................................................................................10
4.2 Storage.......................................................................................................................................10
5Assembly..........................................................................................................................................11
5.1 Preparations...............................................................................................................................11
5.2 Mounting the lubricator...............................................................................................................11
5.3 Connecting the prefilled hose.....................................................................................................12
5.4 Electrical interface connection....................................................................................................12
6Startup and operation .....................................................................................................................13
6.1 Operation and settings ...............................................................................................................13
6.1.1 General................................................................................................................................13
6.1.2 Factory settings...................................................................................................................13
6.1.3 Actions with magnetic pen...................................................................................................14
6.2 Menu and display messages......................................................................................................14
6.3 Selection of parameters t and c..................................................................................................16
6.3.1 Menu structure ....................................................................................................................17
6.4 Error messages..........................................................................................................................18

LUC+125, battery, time-controlled
en-2 1000088470 Revision: 01
6.5 Switching the lubricator on/off....................................................................................................20
6.6 Parameter change in standard menu (Pro)................................................................................ 20
6.7 Triggering single lubrication cycle..............................................................................................21
6.8 Triggering the filling function (venting/filling).............................................................................. 21
6.9 Changing parameters in the "Advanced programming" menu................................................... 22
7Output signals – Time control ....................................................................................................... 23
7.1 Connection assignment – Time control...................................................................................... 23
7.2 Output signals / Display messages – Time control.................................................................... 23
7.3 Standard output signals at PIN 4 – Time control ....................................................................... 24
7.3.1 Empty cartridge signal........................................................................................................ 24
7.3.2 High-signal output (+24 V) at PIN 4.................................................................................... 24
7.3.3 Low-signal output (0 V) at PIN 4......................................................................................... 24
8Maintenance and disposal ............................................................................................................. 25
8.1 Maintenance schedule............................................................................................................... 25
8.1.1 Visual inspection.................................................................................................................25
8.1.2 Cleaning .............................................................................................................................25
8.1.3 Changing the cartridge and battery .................................................................................... 26
8.2 Recommissioning ......................................................................................................................28
8.3 Disposal..................................................................................................................................... 28
9Appendix.......................................................................................................................................... 29
9.1 EC/EU declaration of conformity................................................................................................29

LUC+125, battery, time-controlled
Revision: 01 1000088470 en-3
1 About this manual
This manual contains information which is necessary for the safe use of the LUC+125
(FlexxPump 125), battery version (time-controlled), hereinafter referred to as lubricator.
If this manual is supplied with amendment sheets (e.g. for special applications), then the
information in the amendment is valid. Contradictory specifications in this manual are therefore
void.
The user should contact WITTENSTEIN alpha GmbH with any questions about special
applications. The actual operator must guarantee and ensure that this manual including any
amendments are read and understood by all persons assigned to install, operate, or maintain the
lubricator. For this reason, keep this manual in a suitable and ideally accessible location near the
lubricator.
Inform colleagues who work in the area around the machine about the safety instructions so that
no one sustains injuries.
The original was written in German, all other language versions are translations of the original
manual.
1.1 Information symbols and cross references
The following information symbols are used:
•Indicates an action to be performed
ÜIndicates the results of an action
iProvides additional handling information
A cross reference refers to the chapter number and the header of the target section (e.g.
2.3 "Intended use").
A cross reference to a table refers to the table number (e.g. Table "Tbl - 1").
1.2 Scope of delivery
•Check the completeness of the delivery against the delivery note.
iImmediately notify the carrier, the insurance company, or WITTENSTEIN alpha GmbH in
writing of any missing parts or damage.
i
2 Safety
This manual, especially the safety instructions and the rules and regulations valid for the
operating site, must be observed by all persons working with the lubricator. General legal rules
and regulations as well as applicable rules and regulations on prevention of accidents [e.g.
personal protective equipment (PPE)] and environmental protection must be observed.
2.1 EC/EU Directive
In scope of the EC/EU Directive, commissioning (recommissioning) of a machine at which the
lubricator was installed and/or attached is prohibited until it is verified that the machine complies
with all provisions of the applicable regulation.
An EC/EU declaration of conformity for this lubricator can be found in the appendix (see
chapter 9.1 "EC/EU declaration of conformity").
2.2 Personnel
Only technicians who have read and understood this operating manual may perform work on the
lubricator. Local and/or company regulations apply accordingly.

LUC+125, battery, time-controlled
en-4 1000088470 Revision: 01
2.3 Intended use
For the intended use of the lubricator, the following points must be observed:
- The lubricator is approved only for industrial applications.
- The lubricator may only be put into operation according to the technical specifications (see
chapter 3.7 "Technical data").
- Unauthorized modifications to the lubricator are not permitted.
- Read and observe the operating manual.
- During operation of the lubricator, regular visual inspections must be carried out at the
lubricator itself as well as the lubrication point. Any irregularities and their cause must be
corrected immediately.
- The cartridge must not be refilled.
- The lubricator must not be opened or dismantled.
- Only lubricants which are approved by WITTENSTEIN alpha GmbH may be used.
- Applicable rules and regulations on occupational safety, prevention of accidents and
environmental protection must be observed.
- Any works or tasks with or at the lubricator may only be carried out with authorization (see
chapter 2.2 "Personnel").
Any use other than the previously described intended use or non-compliance with one of the
points specified above is regarded misuse. In this case no liability or warranty claims will be
assumed.
2.4 Reasonably foreseeable misuse
Any usage of the lubricator that exceeds the maximum permitted technical data is considered
misuse and is therefore prohibited.
2.5 Guarantee and liability
Any guarantee and liability claims are excluded for personal injury and/or material damage in
case of:
- Ignoring the information on transport and storage;
- Misuse;
- Improper or not carried out maintenance and repair;
- Incorrect assembly / disassembly or incorrect operation;
- Operation of the lubricator when safety devices and equipment are defective;
- Operation of the lubricator without lubricant;
- Operation of the lubricator with non-approved lubricant;
- Operation of a heavily contaminated lubricator;
- Modifications or changes without written approval by WITTENSTEIN alpha GmbH;
- Opening and/or partly or complete dismantling of the lubricator.

LUC+125, battery, time-controlled
Revision: 01 1000088470 en-5
2.6 General safety instructions
The operation of the lubricator involves remaining risks even when adhering to the intended use.
Defective or faulty electrical connections or unapproved, current-carrying components can
cause serious injuries and even death.
•Have all electrical connection work performed by qualified technicians only.
•Immediately replace damaged cords or plugs.
Loose or overtightened screw connections can cause damage to the lubricator:
•Mount and check all screw connections according to the specified admissible tightening
torques. Use a calibrated torque wrench.
Lubricants are flammable, can cause skin irritation, and can contaminate soil and water:
•In case of fire, do not use a jet of water to extinguish.
•In case of fire, only use suitable extinguishing agents such as powder, foam or carbon
dioxide.
•Always observe the applicable safety instructions by the lubricant manufacturer on the safety
data sheet of the used lubricant.
•Use protective gloves to avoid direct skin contact with lubricants.
•Use and dispose of lubricants properly.
2.7 Structure of warning instructions
Warning instructions are situation-specific. They will
be precisely where tasks are described in which
dangers can arise.
The warning instructions in this manual are
designed according to the following pattern:
A
= safety symbol
B
= signal word
C
= Type and consequence of the danger
D
= Avoiding the danger
2.7.1 Safety symbols
The following safety symbols are used to indicate hazards, prohibitions and important
information:
General danger Electric voltage Flammable Environment
AB
CD

LUC+125, battery, time-controlled
en-6 1000088470 Revision: 01
2.7.2 Signal words
This signal word indicates an imminent danger that will cause
serious injuries or even death.
This signal word indicates a potential hazard that could cause
serious injuries and even death.
This signal word indicates a potential hazard that could cause minor
or serious injuries.
This signal word indicates a potential hazard that could lead to
property damage.
DANGER
WARNING
CAUTION
NOTICE

LUC+125, battery, time-controlled
Revision: 01 1000088470 en-7
3 Description of the lubricator
The lubricator is designed as a highly compact double piston pump for grease as lubricant. The
two pistons run force-controlled and in opposing directions. They are both connected to the same
outlet. The outlet is secured by an integrated check valve. At each dispensing cycle , approx.
0.15 cm³ of lubricant are dispensed. Multiple subsequent dispensing processes can be set.
The lubricator features an electrical interface. The included magnetic pen allows for the
lubrication amount dispensed per time to be adjusted or set to ensure ideal supply of lubricant to
the lubrication point.
The different operating states are displayed at the front as well as other additional information
(e.g. empty cartridge, errors).
The power supply is established via a replaceable battery. The lubricator can be switched on/off
via the M12x1 interface. An external power supply can also be used to transmit information about
an empty cartridge as well as error messages, e.g. to an external control system.
We recommend the battery-powered lubricator exclusively for stand-alone lubrication points
which do not have to be monitored externally or which may not be supplied with external power.
Owing to its increased operational reliability and the expanded settings options for emitting
signals, the 24V-DC version is the better choice in terms of technology and economic efficiency, if
information about an empty cartridge and error messages are to be transmitted to a control
system (e.g. PLC). You can obtain further information about an existing product from
WITTENSTEIN alpha GmbH directly.
3.1 Overview of lubricator components
Pos.
Designation
1
LUC+125, battery version, time-controlled
2
Exchange cartridge LUE+125
3
Assembly bracket
4
Interface M12x1, 4-pole
5
Magnetic pen (in holder)
6
Hose connection
7
Action field
8
Display
9
Name plate
10
CE symbol
-
Battery
Tbl - 1 Overview of lubricator components
3.2 Name plate and labeling
Pos.
Designation
A
Material number
B
Ordering codes (see chapter 3.4 "Ordering codes")
Tbl - 2 Name plate
1
8
7
2
3
4
5
6
9
10
Mat-No: xxxxxxxx
LUC+125-xxxx-xx
A
B

LUC+125, battery, time-controlled
en-8 1000088470 Revision: 01
3.3 Marking
The CE mark is attached to the lubricator housing. The position of the CE mark is described in
chapter 3.1 "Overview of lubricator components".
Manufacturer
DLS Schmiersysteme GmbH
Gewerbering 5
82140 Olching, Germany
Tel.: [phone]
Fax: [phone]
Email: [e-mail]
www.DLS-Schmiersysteme.de
3.4 Ordering codes
3.5 Dimensions
Dimensions can be found
- in our catalog,
- under www.wittenstein-alpha.de.
CAD data and dimension sheets are available upon request.
3.6 Scope of delivery
The lubricator is available in different versions. They can be distinguished by the execution, the
lubricant filling as well as the included accessories.