Wittkopp ANCHOR User manual

Anchor
User Manual
Brief instructions for the daily user
en_Axxxx -Teil 4-Anwenderhandbuch V2.03.docx
1 / 4
Note:
On the cover sheet you can find warning information, and an explanation of the symbols and
terms used, together with the exclusion of liability.
Contents
General................................................................................................................................. 1
Opening ................................................................................................................................ 2
Opening with Dualcode ......................................................................................................... 2
Opening with active delay time.............................................................................................. 3
Triggering a silent alarm........................................................................................................ 3
Menu functions...................................................................................................................... 4
0 Change code.................................................................................................................. 4
General
Depending on the setup, the opening of the lock can be subject to additional restrictions. A
combination of these restrictions is also possible:
1. Delay time → Opening is only possible once a defined delay time has come to the end
(with the exception of user 9).
2. Dualcode → Opening is only possible with two valid user codes.
Normally each user code has a length of 6 digits (0-9). If a silent alarm has been configured,
the number of code digits is increased to 7 places. The 7th code digit is therefore shown greyed
out in the following description.
Ask you administrator (master code) how your system has been set up.

Anchor
User Manual
Brief instructions for the daily user
en_Axxxx -Teil 4-Anwenderhandbuch V2.03.docx
2 / 4
Opening
e.g. factory code master


=
→

The opening code can be
input directly as described
above, without selection.
After a valid code is input the
lock releases the bolt
movement for around 3
seconds. Open the safe
within this time after inputting
the code.
=

Opening with Dualcode
e.g. user 3 begins the input of his code with code 030303
If there is an incorrect input
or if more than 30 seconds
elapse between the two code
inputs then the inputting is
terminated with a long signal
tone.


=
=
The "two pairs of eyes" principle, here user 5 with code
0505050, initiates the opening operation


=
→

=
→


Anchor
User Manual
Brief instructions for the daily user
en_Axxxx -Teil 4-Anwenderhandbuch V2.03.docx
3 / 4
Opening with active delay time
Start through code input


=
→

If a delay time has been
programmed, this must be
started first by inputting a
valid opening code. It can
then be opened by inputting
any desired valid user code
during the time window for
opening.
User 9 cannot start the delay,
but instead can open before
the end of the delay time.
=
♪…2 sec…♪…2 sec…♪…2
sec…♪…

♪…1 sec…♪…1 sec…♪…1
sec…♪…

Input the code for opening


=
→

=
→

If Dualcode / the "two pairs of eyes" principle has been activated the opening operation
corresponds to the described opening procedure after the end of the delay time.
Triggering a silent alarm
e.g. opening code 1234567, alarm addend 2
Start through code input


=
→

The last code digit is
amended in each case if
"silent alarm" is active. The
calculation is done on the
basis of the last digit + alarm
addend. If a number is
carried over then the units
are evaluated:
e.g. code digit 9 + alarm
addend 2 = 11, hence the
last number is = 1
→

=
→

The locking check can be done via the operating lever of the boltwork and should be
performed after each closing and locking.

Anchor
User Manual
Brief instructions for the daily user
en_Axxxx -Teil 4-Anwenderhandbuch V2.03.docx
4 / 4
Menu functions
0 Change code
e.g. change 1234560to 1111111
 ♪ ☼Change menu code
Start through code input


=
Input the new code


=
Confirm the new code


=