Wolf ICON Q2 User manual

INSTRUCTION MANUAL
ENGLISH V1
www.wolnt.co.uk
WIDE TRANSMISSION
RANGE
RUMBLE
ALERT
HUBB
LINK
GLOBAL
MUTE
HIGH VISIBILITY
LEDS
LONG BATTERY
LIFE

2
CONTENTS
FEATURES 3
INSERTING BATTERIES 4
BATTERY LEVEL 4
POWER ON/OFF 4
RUBBER SOCKET HOLDERS 4
CONTROL KNOBS 5
SENSITIVITY LEVELS CONTROL 5
DROPBACK DETECTION 5
LOCAL MUTE 5
LOCAL UNMUTE 5
PAIRING 5
FACTORY DEFAULT 5
ALERTS 6
LED ILLUMINATION COLOURS 6
NIGHTLIGHT LED COLOUR 7
NIGHTLIGHT LED BRIGHTNESS 7
STAINLESS STEEL STUD WITH LOCKING NUT 7
IQ PORT 7
SMART PORT 7
ADJUSTMENT OF BITE ALARM
CONTROLS FROM HUBB 8
DEVICE MENU 8
ROLLER SENSITIVITY SETTING LEVELS 8
LED ILLUMINATION COLOURS 8
BITE LED BRIGHTNESS 8
ADVANCED MENU 8
ALERT TIMEOUT 9
ALERT VOLUME 9
ALERT TONE 9
NIGHTLIGHT SETTINGS 9
DEVICE STATUS 10
BATTERY LEVEL INDICATION 10
RANGE TEST 10
ANTI THEFT 10
MUTE 10
ADJUSTMENT OF BITE ALARM
CONTROLS FROM QrHUBB 10
LED ILLUMINATION COLOURS 10
TONE SETTING 10
BATTERY LEVEL INDICATION 10
RADIO SIGNAL STRENGTH 10
BIVVY LIGHT LINK 10
IQ PORT ON/OFF 10
ANTI-THEFT 10
MUTE 10
MOISTURE OUTLET
NIGHT LIGHT
IQ PORT SMART LED PORT
ISOTOPE SLOTS
LEDLED
NON-SLIP RUBBER GRIP
AND ROD PROTECTOR NON-SLIP RUBBER GRIP
AND ROD PROTECTOR
SPEAKER
VOLUME DIAL
ON/OFF MENU BUTTON
TONE DIAL
PAIR/MUTE BUTTON
STAINLESS LOCKING NUT
STAINLESS STUD
COMPRESSION WASHER

3
FEATURES
•
High Sensitivity Roller Wheel
•
Roller Wheel Detection - 5 Sensitivity Levels
•
Dropback Differentiation
•
Recoil Elimination
•
High Visibility Dual Bite LED’s - 4 Changeable Colours -
Green, Blue, Yellow or Red
•
LED’S Indicates Forward and Backward - Flashes on
dropback
•
LED’S Time adjustable via HUBB and Stealth mode
(LED’S Off)
•
Piezo Speaker
•
Night Light - 4 Changeable Colours and Level Adjustment &
Manual Level Adjustment via HUBB
•
Smart Indicator Port - LED Drive, colour change on bite
detection
•
IQ Port - Links other ICON Accessories
•
HUBB/Qr HUBB Link - Receives and Transmits Commands
•
Pairing Button
•
Menu Button
•
Extreme Transmit/Receive Range 2km Line of sight
•
Fully Sealed Water Resistant Electronics
•
Battery Level Indication
•
Indication type - Event sent to HUBB
•
Mute - 30 Seconds
•
Hard Case
•
Non-Slip Rubber Grip & Rod Protectors
•
Stainless Steel Stud, Locking Nut & Compression Washer
•
Battery Life - 1000 hrs on Standby
•
Beta Light Slots x 2 - Size 6mm x 2mm
•
Rubber Socket Covers
•
Range Test
•
Power Down Alert To HUBB - Anti Theft
•
Volume Settings - Adjustable from Alarm & HUBB
•
Tone Settings - Adjustable from Alarm & HUBB
•
Sensitivity Settings - Adjustable from Alarm & HUBB
•
Tone difference - Run Forward & Dropback
•
Latching Run Time - 60 seconds / 30 seconds /
20 seconds / 10 seconds / 5 seconds Adjustable
via main HUBB
•
Low power mode is available when not paired to HUBB only.
After HUBB pairing LP mode can be re-enabled by a hard
reset of the Bite Alarm
•
Warranty 2 Years with 3rd Year Free
Register you ICON at www.wolfint.co.uk.

4
To insert batteries use a Philips screwdriver and open
2 screws on battery compartment. When inserting new
batteries always replace all of them and turn off Alarm
before replacing. After use of Alarm in damp conditions
leave to dry out somewhere warm before packing away
and if not going to be used for a while it is recommended
to remove batteries in case of leakage. Be careful when
attaching Alarm to banksticks, buzz bars etc. and avoid
over-tightening. See website for full care advice and
instructions.
BATTERY LEVEL
The Battery Level of the
Bite Alarm is displayed
when the button is
pressed..
To power up the Bite
Alarm, press.the
button until the LED’s
turn Blue.
To turn off the Bite
Alarm, press.the
button until the LED’s
turn Blue.
NOTE: Hard case will
not shut off Alarm.
INSERTING BATTERIES POWER ON/OFF
Good battery level
OK battery level
Bad battery level
RUBBER SOCKET HOLDERS
When IQ Port or Smart LED Port are
not being used the rubber socket
holders should be pressed into ports.
When not needed they should be
pressed into the socket holders on
reverse of Alarm.
3 AA 1.5v
Batteries
Battery
Cover

5
LOCAL UN-MUTE
The Bite Alarm can be un-muted after it has been muted.
A single press of the button will un-mute the Bite Alarm.
PAIRING
When the receiver device is ready for pairing with HUBB
(see receiver device instructions), press and hold the
button until indicator LED turns Blue then release Button,
this will initiate pairing.
FACTORY DEFAULT
To reset the Bite Alarm to factory settings, and remove all
user data, hold the button while powering on the Bite
Alarm. After the LED’s illuminate, release the button.
A tone will play to confirm the reset.
LOCAL MUTE
The Bite Alarm can be temporarily muted by pressing the
button, The Bite Alarm is muted for 60 seconds.
CONTROL KNOBS
The Bite Alarm control knobs can be used to adjust various
settings.
The volume knob adjusts the volume of the alerts
on the Bite Alarm.
The tone knob adjusts the pitch of the alerts on
the Bite Alarm.
DROPBACK DETECTION
During a dropback detection, a two tone signal is triggered
and the LED’s should flash.
SENSITIVITY LEVELS CONTROL
The Sensitivity Levels of the Q2 can be adjusted by pressing
the menu button.
Press button and release,
1 flash of LED indicates 2mm Sensitivity
Press button again and release,
2 flashes of LED indicates 6mm Sensitivity
Press button again and release,
3 flashes of LED indicates 18mm Sensitivity
Press button again and release,
4 flashes of LED indicates 35mm Sensitivity
Press button again and release,
5 flashes of LED indicates 60mm Sensitivity

6
ALERTS
ALERT
TYPE LED INDICATION SOUND
Forward
Solid Alert Colour
Single Tone at user
selected pitch.
Dropback
Flashing Alert Colour
Tone at alternating pitch.
IQ Empty
IQ Trigger
Solid Alert Colour
Piercing security tone.
Battery
Critical
Flashing Red
No tone played.
RECOIL ELIMINATION
The Bite Alarm includes Recoil Elimination. The alarm will only
sound if line moves the distance set by the sensitivity dial in
one direction only. If it moves forward and then drops back
immediately as in windy conditions, the alarm won’t sound.
For a given distance of line travel 4mm extra in the opposite
distance is needed before an alert is triggered. LED ILLUMINATION COLOURS
By pressing and holding the menu button the
configuration menu can be entered, indicated by the
LED’s turning white and a special tone.
While in the
configuration menu
the volume knob
adjusts the colour of
the LED colours.
4 colours are
available:
Blue
Yellow
Green
Red
Stealth Mode (Off)
Press menu
button to set
LED colour.
MENU BUTTON

7
IQ PORT
SMART LED PORT
Link to other wired ICON accessories.
Smart LED Drive. Colour matching LEDs and 2 options,
*when used with WOLF Indicators only. Also drives some
3rd party indicators.
STAINLESS STEEL STUD WITH
LOCKING NUT & COMPRESSION
WASHER
Incorporates a 3/8”
stainless steel stud
with locking nut and
compression washer
for attaching the alarm
to your buzz bar or
bankstick. Be careful
when attaching Alarm
to banksticks, buzz
bars etc. and avoid
over-tightening.
LED ILLUMINATION BRIGHTNESS
By pressing and holding the menu button the
configuration menu can be entered, indicated by the
LED’s turning white and a special tone. While in the
configuration menu the pressing the Mute button
toggles the LED and Nightlight brightness high/low.
Modes Selectable:
Bite LED 100% Nightlight 100%
Bite LED 10% Nightlight 100%
Bite LED 100% Nightlight 10%
Bite LED 10% Nightlight 10%
NIGHTLIGHT LED COLOUR
By pressing and
holding the
menu button the
configuration menu
can be entered,
indicated by the
LED’s turning white
and a special tone.
While in the
configuration menu
the Tone knob adjusts
the colour of the
Nightlight LED.
There are 4 selectable colours:
Blue - Yellow - Green - Red - Off.
Press menu button to set Nightlight LED colour.

8
5 Sensitivity Levels.
2mm, 6mm, 18mm, 35mm, or
60mm.
4 Colours: Blue - Yellow - Green - Red - Stealth Mode (Off)
ADJUSTMENT OF BITE ALARM
CONTROLS FROM HUBB
DEVICE MENU
When the HUBB has been paired with Alarms press the
corresponding Alarm channel to change any settings. Press
and hold channel button until ‘Device Menu’ is shown on
screen.
On activation of the bite Alarm the
tone is replicated on the HUBB
and the HUBB LED’s replicate the
alert colour shown on the bite
Alarm. Depending on the HUBB’s
settings, the HUBB will also vibrate
on alert.
When ‘Device Menu’ is shown, use OK button to enter sub
menu.
Go to ‘Sensitivity’ to adjust the connected bite Alarm line
sensitivity. Press OK and adjust setting using left or right
arrows. When confirming this option a message will be sent
to the bite Alarm, if successful you will be notified on screen.
ROLLER SENSITIVITY SETTING LEVELS
< Device Menu >
[Enter]
< Sensitivity >
12 mm
LED ILLUMINATION COLOURS
Go to ‘Alert Colour’ to change the
colour used to display alerts on
the bite Alarm and HUBB. Press
OK and adjust setting using left or
right arrows. When confirming this
option a message will be sent to
the bite Alarm, if successful you
will be notified on screen.
< Alert Colour >
Blue
BITE LED BRIGHTNESS
Go to ‘LED Brightness’ to change
the brightness of the LED’s
displayed on the bite Alarm. Press
OK and adjust setting using left or
right arrows. When confirming this
option a message will be sent to
the bite Alarm, if successful you
will be notified on screen.
< LED Brightness>
73%
ADVANCED MENU
Go back to ‘Device Menu’, Press
right arrow and go to ‘Advanced
Menu’ and use OK button to enter
this menu.
< Advanced Menu >
[Enter]

9
ALERT TIMEOUT
In ‘Advanced Menu’ Go to ‘Alert
Timeout’ to adjust the time that
the LED remains turned on after
an alert on the bite Alarm. Press
OK and adjust setting using left or
right arrows. When confirming this
option a message will be sent to
the bite Alarm, if successful you
will be notified on screen.
60 seconds / 30 seconds / 20
seconds / 10 seconds /
5 seconds
< Alert Timeout >
30 secs
ALERT VOLUME
In ‘Advanced Menu’ go ‘Volume’
to adjust the volume of the bite
Alarm alert. Press OK and adjust
setting using left or right arrows.
When confirming this option a
message will be sent to the bite
Alarm, if successful you will be
notified on screen.
< Volume >
50%
ALERT TONE
In ‘Advanced Menu’ go ‘Alert
Tone’ to adjust the pitch on the
Alarm and the HUBB. Press OK
and adjust setting using left or
right arrows. When confirming this
option a message will be sent to
the bite Alarm, if successful you
will be notified on screen.
< Alert Tone >
28%
Go to option ‘Nightlight Colour’ and adjust as desired. Press
OK and adjust setting using left or right arrows. When
confirming this option a message will be sent to the bite
Alarm, if successful you will be notified on screen.
Colours available: Red - Green - Blue - Yellow and Off.
NIGHTLIGHT SETTINGS
In ‘Advanced Menu’ go ‘Nightlight’.
Find the first option titled
‘Brightness’ and adjust to Manual
or Auto setting. Press OK and
adjust setting using left or right
arrows. When confirming this
option a message will be sent to
the bite Alarm, if successful you
will be notified on screen.
< Nightlight Con >
[Enter]
Go to ‘Copy to Port’. When this option is turned on the
Nightlight colour is copied to any connected Wolf hanger
or swinger. Press OK and adjust setting using left or right
arrows. When confirming this option a message will be sent
to the bite Alarm, if successful you will be notified on screen.

10
DEVICE STATUS
MUTE
Go back to ‘Advanced Menu’ and navigate to the option
titled ‘Device Status’ using right arrow and enter sub menu
using OK button.
ANTI-THEFT
When turning off the connected Alarm, a tone is played on
the Alarm and HUBB for theft prevention.
BATTERY LEVEL INDICATION
Navigate to the option ‘Battery
Level’. This provides a detailed
measurement of the Alarms
battery level.
RANGE TEST
Navigate to the option ‘Range
Test’ and use the OK button to
begin the test. When a connection
is established the HUBB will
report the signal strength of
the connected Alarm and also
indicates that the LED is working.
Pressing the Mute button once should mute all connected
Alarms. On activation neither the HUBB or Alarm will play a
tone. A double press of the Mute button will undo the mute
on the HUBB and Alarms.
< Battery Level >
97%
< Range Test >
[Start]
ADJUSTMENT OF BITE ALARM
CONTROLS FROM Qr HUBB
This provides a detailed measurement of the paired alarms
battery level.
BATTERY LEVEL INDICATION
The Qr HUBB replicates the tone of the linked/paired Alarm.
TONE SETTING
The Qr HUBB will report the signal strength of the connected
alarm and also indicate that the LED is working.
RADIO SIGNAL STRENGTH
Qr HUBB can link other devices to also activate the bivvy
light when the device is active.
BIVVY LIGHT LINK
IQ PORT ON/OFF
LED ILLUMINATION COLOURS
Replicates colour of LED’s.
MUTE
Pressing the Mute button once should mute all connected
Alarms. On activation neither the Qr HUBB or Alarm should
play a tone. A double press of the Mute button should undo
the mute on the Qr HUBB and Alarms.
ANTI-THEFT
When turning off the connected Alarm, a tone should be
played on the Alarm and Qr HUBB for theft prevention.