World Market 618185 User manual

R
Assembly Instructions
2022.08.08
Farmhouse Bookcase 48" Wide
SKU - 618185
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST WORLD MARKET STORE
IF YOU ARE NOT NEAR A STORE PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
All products sold at World Market are not for commercial use and are intended for residential use only.
Page 1

Top Frame
LABEL DESCRIPTION Q.TY
PICTURE
A 1
Bottom Frame
B 1
Left Side Frame
C-1 1
Component List
Right Side Frame
C-2 1
Middle DividerD 1
Door
E 1
Door Support
F 2
Back Panel
G2
Page 2

Fixed Shelf
LABEL DESCRIPTION Q.TY
PICTURE
H 4
Removable Shelf
J4
HandleK 1
Component List
Hardware List
16
Cam lock Ø15 mm
Cam Screw
Connecting Screw M7 x 70 mm
Bolt Ø8 x 30 mm
Flat Washer Ø8 x Ø19 x T2 mm
Lock Washer Ø8 x Ø13 x T2 mm
H-1
H-2
H-3
H-4
H-6
H-7
H-5
H-8
Flat Washer Ø6 x Ø19 x T2 mm
Shelf pin
H-10
H-9
Pan head Screw M3.5 x 15 mm
H-11
Nut Ø8 x 13 mm
Anti Tip Kit
H-13
Decorative Door Bolt M8 x 25 mm
16
12
2
6
16
45
7
1
2
6
6
LABEL DESCRIPTION Q.TY
PICTURE
LABEL DESCRIPTION QTY
PICTURE
Tool List
Allen Key 4 x 110 x 30 mm
T-1
T-2
Phillips Screwdriver (not included)
T-4
T-3 Wrench 13mm
Socket Wrench 13mm
1
1
1
1
H-12 Wood Screw M3.5 x 20 mm 4
Page 3

Before Beginning:
Assembly Preparation
Read instructions, cover to cover.
In case of missing parts, please contact your nearest World Market store or call
our customer service call center at call 1-877-967-5362.
Assemble on a clean non-marring surface (packing foam).
Unpack all hardware bags and components to ensure you have all parts.
Have 2 adults on hand for assembly.
Do not assemble on flooring or carpet.
Save all packaging until finished.
Page 4

Step 1
T-4
H-2
Make sure Cam Screws are
tightened fully as shown
D
(T-4) Phillips Screwdriver
(H-2) Cam Screw x 16
TOP OF
PANELS
Install Cam Screws (H-2) into the pre-drilled holes on Left Side Frame (C-1), Right Side Frame (C-2) and Middle
Divider (D) as shown. NOTE that both sides of Middle Divider (D) require Cam Screws (H-2). Fully tighten using
a Phillips screwdriver (T-4, not included) per illustration above.
C-1
C-2
Assembly Steps
TOP OF
PANEL
BOTTOM OF
PANELS
BOTTOM OF
PANEL
Page 5

Step 2
Page 6
Install Cam Locks (H-1) into the corresponding holes on Fixed Shelf (H) as shown, making sure that the Cam
Screws (H-2) installed on Left Side Frame (C-1), Right Side Frame (C-2). Tighten all Cam Locks (H-1) using
Allen Key (T-1) until they are snug. Carefully set the two shelving pre-assemblies aside, making sure that the
Fixed Shelve (H) do not warp or twist before they are fully secured (in Step 3 and 4).
H
H-1
(T-1) Allen key
(H-1) Cam Lock x 8
Front
Top
T-1
C-1
H
NOTE: Two people are recommended for this assembly step.
NOTE: Cam Lock holes on Fixed Shelves (H) should all face toward the BOTTOM of the assembly. There is a
smaller distance between the Top edges of Left/ Right Side Frames (C-1, C-2) and Fixed Shelves (H) than
between the BOTTOM edges of Left/ Right Side Frames (C-1, C-2), and Fixed Shelves(H).
C-2
Follow Arrow
direction

Step 3
Page 7
Step 4
Install Cam Locks (H-1) into the corresponding holes on Fixed Shelf (H) that were installed on Right Side Frame
(C-2) as shown. Ensure arrows on Cam Locks (H-1) point toward the Cam Screws (H-2). Insert Cam Screws
(H-2) that have previously been installed in Middle Divider (D) into receiving holes in Fixed Shelves (H). Tighten
all Cam Locks (H-1) using Allen Key (T-1) until they are snug.
D
H-1
(H-1) Cam Lock x 4
Front
Top
T-1
Install Cam Locks (H-1) into the corresponding holes on Fixed Shelf (H) that were installed on Left Side Frame
(C-1) as shown. Ensure arrows on Cam Locks (H-1) point toward the Cam Screws (H-2). Insert Cam Screws
(H-2) that have previously been installed in Middle Divider (D) into receiving holes in Fixed Shelves (H). Tighten
all Cam Locks (H-1) using Allen Key (T-1) until they are snug.
H-1
(T-1) Allen key
(H-1) Cam Lock x 4
Front
Top
T-1
C-1
C-2
H
H
H
C-1
D
H
(T-1) Allen key
Follow Arrow
direction
Follow Arrow
direction

Step 5
Page 8
Step 6
Install and secure Left Side Frame (C-1) and Right Side Frame (C-2) to Top Frame (A) using
Connecting Screws (H-3). Engage all screws before fully tightening using Allen Key (T-1).
NOTE: Please reference the "TOP" directional arrow in the illustration below to help with this assemply step.
H-3
T-1
A
(T-1) Allen key
(H-3) Connecting Screw x 6
Install and secure Left Side Frame (C-1) and Right Side Frame (C-2) to Bottom Frame (B) using Connecting
Screws (H-3). Engage all screws before fully tightening using Allen Key (T-1).
NOTE: Please reference the "TOP" directional arrow in the illustration below to help with this assemply step.
H-3
T-1
B
(T-1) Allen key
(H-3) Connecting Screw x 6
Front
Top
Front
Top
C-1
D
C-2
B

Step 7
Page 9
Step 8
Using a second person to assist you, carefully turn the assembled unit upright. Insert Shelf Pins (H-9) into the
desired hole locations on Left Side Frame (C-1) and Right Side Frames (C-2) and Middle Divider (D) . Insert
Shelf (J) into position as shown, making sure they rest evenly on each Shelf Pin (H-9).
H-9
(H-9) Shelf Pin x 16
Using a second person to assist you, carefully turn the assembled unit upside down as shown.
Position and secure Back Panels (G) to the back of assembled unit with Pan Head Screws (H-10) by using the
Phillips Screwdriver (T-4). Do not over tighten.
Position and secure the middle to Back Panels (G) to the back of assembled unit with Pan Head Screws (H-10)
and Flat Washer (H-11) by using the Phillips Screwdriver (T-4). Do not over tighten.
(H-10) Pan Head Screw x 45
(T-4) Phillips Screwdriver
(H-11) Flat Washer x 7
x38
T-4
H-10
T-4
H-10
H-11
x7
Front
Top
Front
Top
NOTE: Two people are recommended for this assembly step.
G
C-1
C-2
A
NOTE: Two people are recommended for this assembly step.
J
G
J
J
J

Step 9
Step 10
H-6
H-8
H-7
H-8
H-6
H-7
T-2
K
(H-6) Nut x 2 (H-8) Flat Washer x 2
(H-7) Lock Washer x 2 (T-2) Socket Wrench x 1
(H-4) Bolt x 2
(H-5) Decorative Door Bolt x 2
(H-6) Nut x 6
(H-8) Flat Washer x 6
(H-7) Lock Washer x 6 (T-2) Socket Wrench x 1
(T-3) Wrench x 1
Option 1
H-8
H-7
H-6
T-2
T-3
H-4
Position and secure Handles (K) to Door (E) with Nuts (H-6), Lock Washers (H-7), Flat Washers (H-8), stacking
the hardware in the order as shown. Fully tighten nuts using Socket Wrench (T-2).
H-6
H-7
H-8
H-5
Option 2
H-6
H-7
H-8
H-5
Insert and secure Door Supports (F) to the top of Door (E) with Nuts (H-6), Lock Washer (H-7), Flat Washers
(H-8), and Bolts (H-4), stacking the hardware in the order as shown. Use Socket Wrench (T-2) and Wrench (T-3)
and fully tighten nuts and bolts. Secure Door Supports (F) to the top of Door (E) with Wood Screws (H-12) by
using Phillips Screwdriver (T-4)
Insert Nuts (H-6), Lock washers (H-7), Flat washers (H-8), and Decorate Door Bolts (H-5) in the holes at the
bottom of Door (E), staking the hardware in the order as shown. Fully tighten all bolts using Socket Wrench (T-2).
Front
NOTE: The Door (E) can be oriented with the handle on the left or the right. Start this step by positioning the
door in the desired configuration.
Page 10
H-8
H-7
H-6
T-2
T-3
(H-12) Wood Screw x 4 (T-4) Phillips Screwdriver
H-12
H-4
H-12
T-4
T-4
E
E
E
F
F
K
T-2 T-2