World Market Kellen 626640 User manual

R
Kellen Low Fluted Glass Cabinet
SKU 626640
PAGE 1
2023.07.26
Assembly Instructions
ALL PRODUCTS SOLD AT WORLD MARKET ARE NOT
FOR COMMERCIAL USE AND ARE INTENDED FOR
RESIDENTIAL USE ONLY
Thank you for your purchase. If you have any questions pertaining to the assembly of this
furniture piece, please contact the nearest World Market store. If you are not near a store,
please call our customer service call center toll free at 877-967-5362 for assistance.

LABEL DESCRIPTION Q.TY
PICTURE
1
Top Frame
A
Component List
1
Bottom Frame
B
1
Left Side Frame
C-1
1
Right Side Frame
C-2
1
Divider Frame
D
Adjustable Shelf 2
Support Rail
F
1
E
FRONT
FRONT
TOP
TOP
TOP
TOP
TOP
PAGE 2

LABEL DESCRIPTION Q.TY
PICTURE
1
G-1
Component List
Left Back Panel
4
Leg
J
1
Right Sliding Door
(Tempered Glass)
Left Sliding Door
(Tempered Glass)
1
G-2
KLid 2
Right Back Panel
1
I-1
I-2
TOP
FRONT
TOP
FRONT
TOP
TOP
TOP
TOP
PAGE 3

LABEL DESCRIPTION Q.TY
PICTURE
Anti Tip-kit
8
6
8
8
Cam lock Ø15 mm
1
Shelf Pin Ø6
H-1
Cam Screw
Short Connecting Screw
M7 x 50 mm
Hardware List
2
Long Connecting Screw
M7 x 70 mm
4
Long Pan Head Screw M4 x 60 mm
24
Short Pan Head Screw M3.5 x 15
mm
Nut M8 x 13mm
Lock Washer Ø8 x Ø13 x T2 mm
Small Flat Washer Ø8 x Ø16 x T2
mm
8
8
8
Medium Flat Washer
Ø6 x Ø19 x T1 mm
Connector Bolt M6 x 10 mm
(inside) 2
Allen Bolt M6 x 10 mm 2
Large Flat Washer Ø10 x Ø20 x T2
mm 2
H-2
H-3
H-4
H-5
H-6
H-7
H-8
H-9
H-10
H-11
H-12
H-13
H-14
H-15
4
PAGE 4

Tool List
LABEL DESCRIPTION QTY
1
T-1
Phillips Screwdriver
(Not Included)
PICTURE
Allen Key
4 x 110 x 30 mm
Wrench 13 mm
Triangle
T-2
T-3
T-4
1
1
1
PAGE 5

Assembly Preparation
Before Beginning:
Read the assembly instructions, cover-to-cover. Save any Care and Maintenance instructions pages for
after the assembly has been completed.
In case of missing parts, please contact your nearest World Market store or call our customer service call
center at call 1-877-967-5362.
Assemble on a clean non-marring surface (such as the product's packing foam).
Unpack all hardware bags and components to ensure you have all parts. Take note of bolt hardware
size differences and components that may have directional labels (Example: TOP or FRONT).
It is always recommended to have 2 adults on hand for assembly.
Do not assemble on hard, abrasive flooring or carpeted surfaces that can damage or get caught in the
components during assembly.
Do not discard any packaging until the product has been fully assembled.
WARNING: Small parts are a choking hazard. Adult supervision is required before, during, and after
assembly.
PAGE 6

Step 1
Assembly Steps
(T-4) Phillips Screwdriver
(H-2) Cam Screw x 8
Step 1.1:
Make sure Cam Screws are
tightened fully as shown
x8
FRONT OF
PANELS
TOP
Step 1.2:
T-4
A
C-2
C-1
IMPORTANT:
Please make note of the different
hardware sizes and ensure you are
using the correct size hardware (bolts,
screws, and washers) for each step.
H-2
Step 1.1: Place Top Frame (A) upside down onto a padded, non-marring surface. Install Cam Screws (H-2) into the
pre-drilled holes on Top Frame (A) as shown. Fully tighten using a Phillips screwdriver (T-4, not included) per
illustration above.
Step 1.2: Place Left Side Frame (C-1) and Right Side Frame (C-2) upside down onto a padded, non-marring surface.
Install Cam Screws (H-2) into the pre-drilled holes on Left/ Right Side Frame (C-1/ C-2) as shown. Fully tighten
using a Phillips screwdriver (T-4, not included) per illustration above.
PAGE 7

Step 2
Step 3
TOP
FRONT
x3
x2
Step 2.1: Using a second person to assist you, Install and secure Bottom Frame (B) to Right Side Frame (C-2) using
Short Connecting Screws (H-3) .
Step 2.2: Install and secure Bottom Frame (B) to Divider Frame (D) using Long Connecting Screws (H-4)
Engage all screws before fully tightening using Allen Key (T-1). Do not over tighten.
Using a second person to assist you, attach Support Rail (E) to Right Side Frame (C-2) by inserting previously
installed Cam Screws (H-2) and dowels into receiving holes. The midpoint of Support Rail (E) should rest on
Divider Frame (D).
NOTE: Do not yet secure assembly with Cam Locks (H-1).
Step 2.2:
C-2
D
B
Step 2.1:
H-3
IMPORTANT:
Please make note of the different
hardware sizes and ensure you are
using the correct size hardware (bolts,
screws, and washers) for each step.
H-4
T-1
T-1
C-2
B
C-2
D
E
E
C-2
(H-3) Short Connecting Screw x 3
(H-4) Long Connecting Screw x 2
(T-1) Allen key
FRONT
TOP
PAGE 8

Step 4
Step 5
(H-13) Lock Washer x 8
(H-12) Small Flat Washer x 8 (H-14) Nut x 8
(T-2) Wrench
Follow arrow
direction
(H-1) Cam Lock x 2 (T-1) Allen key
(H-3) Short Connecting Screw x 3
x3
x2
x8
Step 4.1: Install Cam Locks (H-1) into the corresponding holes along Support Rail (E) as illustrated. Make sure
arrows on Cam Locks point to the screw upon insertion. Secure all Cam Locks (H-1) using Allen Key (T-1), turning
them clockwise until they are snug. DO NOT OVERTIGHTEN the Cam Locks.
Step 4.2: Install and secure Bottom Frame (B) to Left Side Frame (C-1) using Short Connecting Screws (H-3) first
by hand, then fully tightening using the provided Allen Key (T-1). Do not over tighten.
Use the provided 90oTriangle (T-3) and adjust the corners to make sure the cabinet is square. Ensure the Bottom
Frame (B) is oriented correctly.
Step 4.1: Step 4.2:
B
D
C-2
C-1
E
Install and secure Legs (J) to Bottom Frame (B) with Small Flat Washers (H-12), Lock Washers (H-13) and Nuts
(H-14) using provided Wrench (T-2), stacking the hardware in the order as shown. Engage all Nuts (H-14) first, then
fully tighten. DO NOT over tighten.
(T-3) Triangle
H-1
T-1
H-3
T-1
J
C-1
C-2
J
D
BH-14
H-13
H-12
T-2
J
Triangle
90°
TOP
FRONT
FRONT
TOP
PAGE 9

Step 6
Step 7
(H-1) Cam Lock x 6 (T-1) Allen key
(H-5) Long Pan Head Screw x 4 (T-4) Phillips Screwdriver
Using a second person to assist you, carefully position Top Frame (A) onto the assembly. Align all of the cam
screws (installed in Step 1) with their corresponding holes on Left/ Right Side Frame (C-1/ C-2) and Divider Frame
(D) following the orientation directions above. The arrow on the Cam Lock (H-1) must point towards the Cam
Screw (H-2) when first inserting the Cam Lock. Once confirmed, fully tighten all Cam Locks (H-1) by turning
clockwise using Allen Key (T-1) until they are snug. DO NOT over tighten Cam Locks. Check that the cabinet is
square (90 degree) using the Triangle (T-3).
Install and secure Support Rail (E) to Top Frame (A) using Long Pan Head Screw (H-5) by using the Phillips
Screwdriver (T-4). Do not over tighten.
(T-3) Triangle
Follow arrow
direction
H-1
T-1
Triangle
90°
T-3 x6
A
B
C-1
C-2
D
T-4
H-5
x4
D
C-1
C-2
A
E
B
E
FRONT
TOP
FRONT
TOP
PAGE 10