World Market 502422 User manual

Page 1
Adirondack Chair
SKU
NOT FOR COMMERCIAL USE
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
Assembly Instructions
502422, 518826, 551931, 551932, 551933,
597227, 608549, 608550, 608551, 608555

Page 2
Component List
LABEL
PICTURE
DESCRIPTION
QTY
A
Seat Slat
1
B
Seat
1
C
Left Leg
1
D
Right Leg
1
E
Backrest
1
F
Left Armrest
1
K
Right Armrest
1
Hardware List
LABEL
PICTURE
DESCRIPTION
QTY
H-1
Allen Bolt
M6 x 35mm
14
H-2
Spring Washer
1 x 7/10mm
6
H-3
Flat Washer
1 x 6.5/14mm
6
H-4
Wood Dowel
8 x 20mm
4
Tool List
LABEL
PICTURE
DESCRIPTION
QTY
T-1
Allen Key
1

Page 3
Assembly Preparation
Before Beginning:
Unpack all hardware bags and components to ensure you have all parts-
Read instructions, cover to cover-
Have 2 adults on hand for assembly-
Do not assemble on flooring or carpet-
Assemble on a clean non-marring surface (packing foam)-
Save all packaging until finished-
In case of missing parts, please contact your nearest Cost Plus World
Market store or call our customer service call center at call 1-877-967-5362.

Page 4
Assembly Steps
Step 1
(H-1) Allen Bolt x 2
(T-1) Allen Key
Step 2
- Place Right Armrest (K) onto a non-marring surface with the pre-drill holes facing up. Insert 2
Wood Dowels (H-4) into the parallel pre-drilled holes as shown.
- Attach Right Leg (D) to Right Armrest (K) using the 2 Wood Dowels (H-4) and Allen Bolt (H-1)
through the center hole on block.
- Engage the bolt using Allen Key (T-1) but do not fully tighten it.
- Repeat the process for the Left Armrest (F) and Left Leg (C) assembly.
(H-4) Wood Dowel x4
(H-1) Allen Bolt x2
(T-1) Allen Key
- Place Seat (B) down onto a non-marring surface and on its side as shown.
- Attach each end of Seat Slat (A) to Seat (B) using Allen Bolts (H-1) and Allen Key (T-1).
Engage the bolts but do not fully tighten them.
Note: Do not fully tighten any bolts until the last step.

Page 5
Step 3
Step 4
Assembly Steps
(H-1) Allen Bolt x6
(T-1) Allen Key
(H-2) Spring Washer x6
(H-3) Flat Washer x6
- Attach the Right Leg (D) to the assembled Seat (B) and secure using 3 Allen Bolts (H-1),
Spring Washers (H-2) and Flat Washers (H-3), stacking the hardware in the order as shown.
- Engage the bolts using Allen Key (T-1) but do not fully tighten them.
- Repeat the same process for the Left Leg (C).
(H-1) Allen Bolt x4
(T-1) Allen Key
- Attach Backrest (E) to each end of the Seat (B) assembly and both Armrests (C/D).
- Secure using Allen Bolts (H-1) and Allen Key (T-1). Engage the bolts but do not fully tighten
them.

Page 6
Step 5
Care & Maintenance
CAUTION
As with any wood, the color may fade if left in direct sunlight or inclement weather.
For Natural wood finishes, we recommend using our Outdoor Wood Finish to help
preserve the finish.
Due to the protective finish, there may be a light film on the surface of wood. To
remove, wipe with a clean soft dry cloth. Do not use soap or a cleanser to remove
the film. Overtime, direct sunlight will also remove the film.
Assembly Steps
Do not put hot items directly on furniture surface.
Do not clean furniture with harsh cleansers or polish.
Do not place furniture near heating or cooling vents.
Do not write on furniture without a padded barrier to protect the surface
Store furniture or use an appropriate furniture cover during cold or
inclement weather.
Not for commercial use. For residential use only.
Dust and pick-up spills using a clean, non-colored, lint-free cloth.
Stains may be removed with a damp cloth.
Fully tighten ALL Allen bolts from Steps 1-4 at this time using Allen Key (T-1). Do not over-
tighten bolts. Carefully turn the assembly upright and the chair is now ready for use.