World Market ALICANTE II 597208 User manual

NEAREST WORLD MARKET STORE.
Page 1
NOT FOR COMMERCIAL USE.
ALICANTE II CORNER
SKU - 597208

G1
Left Back Cushion
F1
Right Back Cushion
H1
Seat Cushion
Left Back Frame
H-5 Long Allen Bolt (M6x40)mm 2
A
B
C
D
E
Seat Frame
Right Leg
Left Leg
Right Back Frame
1
H-1
H-2
H-3
Short Allen Bolt (M6x15)mm
Spring Washer
Flat Washer (M6x1)mm
Allen Key
12
17
17
1
Page 2
1
1
1
1
H-4
T-1
Medium Allen Bolt (M6x25)mm
3

Page 3
World.World Market store
or call our customer service call center at call 1-877-967-5362.

C
H-1
H-2
H-3
Short Allen Bolt (M6x15)mm
Spring Washer
Flat Washer (M6x1)mm
x12
x12
x12
T-1 Allen Key
x1
H-1
B
H-3
T-1
Page 4
Step 1
A
H-2 Clockwise
Prepare the assembly by placing Seat Frame (A), Right Leg (B) and Left Leg
(C),
down onto a
padded, non-marring surface. Arrange the components as shown above.
Secure the of Seat Frame (A) to both Left/Right Legs (B/ C) using Short Allen Bolt (H-1),
Spring Washers (H-2) and Flat Washers (H-3), stacking the hardware in the order as shown.
Engage all bolts first, and then fully tighten them using Allen Key (T-1).
x4

H-2
H-3
T-1
Clockwise
E
D
Page 5
H-5
H-2
H-3
Long Allen Bolt (M6x40)mm
Spring Washer
Flat Washer (M6x1)mm
Allen Key
x2
x2
x2
T-1 1
Step 2
H-5
Insert Back Frame (D),(E) as shown. Secure Right Back Frame (D) to Left Back Frame (E) using
Long Allen Bolts (H-5), Spring Washers (H-2) and Flat Washers (H-3), stacking the hardware in the
order as shown.
Engage all bolts first, and then fully tighten them using Allen Key (T-1).
x2

H-4
H-2
H-3
Medium Allen Bolt (M6x25)mm
Spring Washer
Flat Washer (M6x1)mm
Allen Key
x3
x3
x3
T-1 x1
Page 6
Step 3
H-1
T-1
Clockwise
Place Seat Frame upside down. Next, using Medium Allen Bolts (H-4), Spring Washers (H-2)
and Flat Washers (H-3), stacking the hardware in the order as shown.
Engage all bolts first, and then fully tighten them using Allen Key (T-1).
x2
H-2
H-3
H-1
H-2
H-3
x1
T-1
Clockwise

Page 7
H
G
F
Step 4
Leveler Feet Cap.
Using a second person to assist you, turn the Corner Seat upright. Place Seat Cushion (H),
Back Cushion (G) and (F) into position as shown. Ensure all bolts have been fully tightened.
Assembly is now complete and the chair is ready for use.
NOTE: Levelers can be pre-installed for height adjustment to achieve stability only AFTER
the unit is moved to the desired location. DO NOT drag the unit as this may damage the
levelers.
Ensure all bolts are fully tightened every 3 months to ensure stability.

CUSHION AND SLIP COVER CARE:
For minor spots wipe with a wet cloth and use a mild detergent. Do not use bleach.
Slip covers can also be placed in a washing machine.
Remove the slip cover from the insert, do not place insert in the washing machine.
Use gentle cycle, cold water and no bleach.
Line dry, do not place in the dryer.
We use a higher density foam to ensure the cushion does not break down in the outdoor elements.
Cushion will soften over time.
Flip the cushions to maintain the quality.
For best results remove cushions during cold or inclement weather and store in a dry area.
If cushions do become wet allow to completely dry before storing to prevent mold and mildew.
Page 8

Page 9