World Market Amira 618189 User manual

R
Amira Arch-Top 4-Door Cabinet
SKU 618189
2023.07.26
Assembly Instructions
ALL PRODUCTS SOLD AT WORLD MARKET ARE NOT
FOR COMMERCIAL USE AND ARE INTENDED FOR
RESIDENTIAL USE ONLY
Thank you for your purchase. If you have any questions pertaining to the assembly of this
furniture piece, please contact the nearest World Market store. If you are not near a store,
please call our customer service call center toll free at 877-967-5362 for assistance.
PAGE 1

LABEL DESCRIPTION Q.TY
PICTURE
1
Left Top Frame
A
1
Right Top Frame
B
1
Middle Top Frame
C
1
Fixed Upper Shelf
D
2
Adjustable Shelf
E
1
Fixed Lower Shelf
F
1
Bottom Panel
G
Component List
1
Upper Horizontal Back Support
H
1
Lower Horizontal Back Support
J
FRONT
FRONT
FRONT
FRONT
TOP
TOP
TOP
TOP
TOP
TOP
TOP
TOP
TOP
FRONT
FRONT
PAGE 2

LABEL DESCRIPTION Q.TY
PICTURE
1
Vertical Back Support
K
Component List
1
Left Side Frame
L-1
1
Right Side Frame
L-2
1
Lower Left Back Panel
M-1
1
Lower Right Back Panel
M-2
1
Upper Back Panel
N
TOP
TOP
TOP
TOP
TOP
TOP
PAGE 3

LABEL DESCRIPTION Q.TY
PICTURE
1
Upper Left Door
(Tempered Glass)
P-1
Component List
1
Upper Right Door
(Tempered Glass)
P-2
1
Lower Left DoorQ-1
1
Lower Right Door
Q-2
1
Base Frame 1
R
4
Handle
T
1
Base Frame 2
S
TOP
TOP
TOP
TOP
TOP
TOP
TOP
PAGE 4

LABEL DESCRIPTION Q.TY
PICTURE
Anti Tip-kit
10
56
10
22
22
Cam lock Ø15 mm
1
Pan head Screw M3.5 x 15 mm
Shelf Pin Ø6
H-1
H-2
H-3
H-4
H-5
H-12
Cam Screw
Connecting Screw M7 x 50 mm
Short Allen Bolt M6 x 25 mm
Lock Washer Ø6 x Ø10.5 x T2 mm
Flat Washer Ø6 x Ø16 x T2 mm
Long Allen Bolt M6 x 50 mm
1
H-6
8
H-7 9
H-8 9
H-9
Handle Bolt M4 x 30 mm 8
H-10
Flat Washer Ø5 x Ø10 x T1 mm 8
H-11
LABEL DESCRIPTION QTY
1
T-1
T-2 Phillips Screwdriver
(Not Included) 1
PICTURE
Allen Key 4 x 110 x 30 mm
Hardware List
Tool List
1
T-3 Triangle
PAGE 5

Assembly Preparation
Before Beginning:
Read the assembly instructions, cover-to-cover. Save any Care and Maintenance instructions pages for
after the assembly has been completed.
In case of missing parts, please contact your nearest World Market store or call our customer service call
center at call 1-877-967-5362.
Assemble on a clean non-marring surface (such as the product's packing foam).
Unpack all hardware bags and components to ensure you have all parts. Take note of bolt hardware
size differences and components that may have directional labels (Example: TOP or FRONT).
It is always recommended to have 2 adults on hand for assembly.
Do not assemble on hard, abrasive flooring or carpeted surfaces that can damage or get caught in the
components during assembly.
Do not discard any packaging until the product has been fully assembled.
WARNING: Small parts are a choking hazard. Adult supervision is required before, during, and after
assembly.
PAGE 6

Step 1
(T-2) Phillips Screwdriver
(H-2) Cam Screw x 22
T-2
H-2
Step 1.1: Install Cam Screws (H-2) into the pre-drilled holes on Left Side Frame (L-1) and Right Side Frame (L-2)
as shown. Fully tighten using a Phillips screwdriver (T-2, not included) per illustration above.
Step 1.2: Place Left Top Frame (A), Right Top Frame (B) and Middle Top Frame (C) on their front edges onto a
padded, non-marring surface. Install Cam Screws (H-2) into the pre-drilled holes on Top Frame (A/B/C) as shown.
Fully tighten using a Phillips screwdriver (T-2, not included) per illustration above.
Step 1.3: Install Cam Screws (H-2) into the pre-drilled holes on Upper Horizontal Back Support (H) as shown. Fully
tighten using a Phillips screwdriver (T-2, not included) per illustration above.
Step 1.1:
TOP OF
PANELS
Make sure Cam Screws are
tightened fully as shown
L-1
L-2
Assembly Steps
Step 1.2:
Step 1.3:
B
C
A
H
PAGE 7

Step 2
Step 3.1
Attach the Fixed Lower Shelf (F) to the Right Side Frame (L-2) by inserting pre-installed Cam Screws and dowels
as shown. Insert the BOTTOM end of Vertical Back Support (K) into the corresponding holes on Lower Horizontal
Back Support (J). Take note of the directional arrow on Vertical Back Support (K). Attach the Vertical Back
Support (K) in the rear slot of the Fixed Lower Shelf (F).
Note: A second person should hold the Right Side Frame/Bottom Panel assembly while performing this assembly
step.
Using a second person to assist you, attach Lower Horizontal Back Support (J) to Right Side Frame (L-2) by
inserting previously installed Cam Screws (H-2) and dowels into receiving holes. Next, temporarily secure
assembly to Bottom Panel (G) by inserting pre-installed dowels into receiving holes on Bottom Panel (G).
NOTE: Do not yet secure assembly with Connecting Screws (H-3) or Cam Locks (H-1).
H-2
J
G
TOP Please note the orientation of L-1 and L-2
Panel. The TOP of the panel is indicated
where the shelf pin hole grids stop and there
is a flat gap.
L-2
K
F
F
G
K
L-2
JK
J
TOP
H-2
NOTE: View in this step is
now from the opposite end
as previous step.
FRONT
J
GL-2
L-2
F
FRONT
PAGE 8

Step 3.2
Step 3.3
Attach Upper Horizontal Back Support (H) to the Fixed Upper Shelf (D) by inserting pre-installed dowels as shown.
There are 2 Cam Locks (H-1) to install into the corresponding holes along Fixed Upper Shelf (D) as illustrated. Make
sure arrows on Cam Locks point to the screw upon insertion. Secure all Cam Locks (H-1) using Allen Key (T-1),
turning them clockwise until they are snug. DO NOT OVERTIGHTEN the Cam Locks.
F
G
K
L-2
J
H
D
L-2
H-2
H-2
H
D
L-2
H
K
D
Attach the assembly from step 3.2 to the Right Side Frame (L-2) by inserting pre-installed Cam Screws and dowels
as shown. Attach Upper Horizontal Back Support (H) to the TOP end of the Vertical Back Support (K) and to the
Right Side Frame (L-2) by inserting pre-installed Cam Screws and dowels as shown.
* Note:
- A second person should hold the Right Side Frame/Bottom Panel assembly while performing this assembly
step.
- The orientation of the Fixed Upper Shelf (D). Cam lock holes should face the Fixed Lower Shelf (F).
- Slightly separate Upper Horizontal Back Support (H) from the Fixed Upper Shelf (D) (if needed) to get the
cam screws and dowels to insert.
H
D
H
D
Follow Arrow
direction
(T-1) Allen key
(H-1) Cam Lock x 2
H-2
FRONT
TOP
PAGE 9
x2

Step 3.4
D
L-1
G
L-2
F
L-1 J
H-2
H-2
H
Using a second person to carefully hold the assembly, attach Fixed Upper/ Lower Shelf (D/F), Upper/ Lower
Horizontal Back Support (H/J) and Bottom Panel (G) to Left Side Frame (L-1) by inserting pre-installed Cam
Screws (H-2) and dowels into corresponding holes. After this step, entire assembly should be able to stand on its
own.
L-1
G
J
H
D
FRONT
TOP
PAGE 10