World Market Amira User manual

R
Assembly Instructions
Amira Sideboard
SKU - 622520
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST WORLD MARKET STORE
IF YOU ARE NOT NEAR A STORE PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
All products sold at World Market are not for commercial use and are intended for residential use only.
Page 1
2023.03.27

1
Right Side Frame
G-2
LABEL DESCRIPTION Q.TY
PICTURE
1
Top FrameA
Component List
Page 2
1
Back Support
B
2
Adjustable Shelf
C
1
Bottom Frame
D
1
Base Frame 1
E
1
Base Frame 2
F
1
Left Side Frame
G-1

LABEL DESCRIPTION Q.TY
PICTURE
Component List
Page 3
1
Divider Frame
H
1
Left Door A
(Tempered Glass)
J-1
1
Right Door A
(Tempered Glass)
J-2
4
Handle
K
2
Lid
L
1
Left Back Panel
M-1
1
Right Back Panel
M-2
1
Left Door B
(Tempered Glass)
J-3
1
Right Door B
(Tempered Glass)
J-4

Page 4
LABEL DESCRIPTION Q.TY
PICTURE
Anti Tip-kit
8
24
9
10
10
Cam lock Ø15 mm
1
Short Pan head Screw M3.5 x 15 mm
Shelf Pin Ø6
H-1
H-2
H-3
H-4
H-5
H-17
Cam Screw
Connecting Screw M7 x 50 mm
Medium Allen Bolt M6 x 25 mm
Lock Washer Ø6 x Ø10.5 x T2 mm
Medium Flat Washer
Ø6 x Ø16 x T2 mm
Long Allen Bolt M6 x 50 mm
1H-8
8
H-9
9H-10
9
H-11
Handle Bolt M4 x 30 mm 8 H-15
Small Flat Washer Ø5 x Ø10 x T1 mm 8H-16
LABEL DESCRIPTION QTY
1
T-1
Triangle
PICTURE
Allen Key 4 x 110 x 30 mm
Hardware List
Tool List
4Large Flat Washer Ø6 x Ø19 x T2 mm
H-7
Connector Bolt M6 x 10 mm (inside) 2
H-12
Short Allen Bolt M6 x 10 mm 2
H-13
Extra Large Flat Washer
Ø10 x Ø20 x T2 mm 2
H-14
1
T-2
4Long Pan head Screw M3.5 x 20 mm
H-6
Phillips Screwdriver (Not Included) 1
T-3

Assembly Preparation
Before Beginning:
Page 5
Read instructions, cover to cover.
In case of missing parts, please contact your nearest World Market store or call
our customer service call center at call 1-877-967-5362.
Assemble on a clean non-marring surface (packing foam).
Unpack all hardware bags and components to ensure you have all parts.
Have 2 adults on hand for assembly.
Do not assemble on flooring or carpet.
Save all packaging until finished.
WARNING: Small parts are a choking hazard. Adult Supervision is required
before, during, and after assembly.

Page 6
Step 1
(T-3) Phillips Screwdriver
(H-2) Cam Screw x 10
Step 1.1:
Make sure Cam Screws are
tightened fully as shown
Assembly Steps
Step 1.2:
T-3
H-2
FRONT OF
PANELS
A
G-1
G-2
Step 1.1: Place Top Frame (A) upside down onto a padded, non-marring surface. Install Cam Screws (H-2) into
the pre-drilled holes on Top Frame (A) as shown. Fully tighten using a Phillips screwdriver (T-3, not included)
per illustration above. Do not under OR over tighten.
Step 1.2: Place Left Side Frame (G-1) and Right Side Frame (G-2) upside down onto a padded, non-marring
surface. Install Cam Screws (H-2) into the pre-drilled holes on Left/ Right Side Frame (G-1/ G-2) as shown.
Fully tighten using a Phillips screwdriver (T-3, not included) per illustration above. Do not under OR over tighten.
T-3
H-2
x2
x8
IMPORTANT:
Please make note of the different
hardware sizes and ensure you are
using the correct size hardware (bolts,
screws, and washers) for each step.

Page 7
Step 2.1
(T-1) Allen key
(H-3) Connecting Screw x 9
H-3
x9
T-1
G-2
G-1
B
D
G-2
G-1
H
B
Using a second person to assist you, attach Back Support (B) to Left/ Right Side Frame (G-1/ G-2) by inserting
previously installed Cam Screws (H-2) and dowels into receiving holes. Be careful with the hinges so they are not
damaged, or damage the floor.
NOTE: Do not yet secure assembly with Connecting Screws (H-3) or Cam Locks (H-1).
Position Divider Frame (H) with the middle of the Back Support (B) as shown. Place Bottom Frame (D) onto
assembly by inserting the dowels in Left/ Right Side Frames (G-1/G-2) and Divider Frame (H) into the receiving
holes in the Bottom Frame. Use the provided 90oTriangle (T-2) and adjust the corners to make sure the
sideboard is square. Ensure the Bottom Frame (D) is oriented correctly. Secure the connection by engaging all
Connecting Screws (H-3) first by hand, then fully tightening using the provided Allen Key (T-1). Do not over
tighten.
Front
Top
Front
Top
Step 2.2
Triangle
90°
T-2
(T-2) Triangle

Page 8
Step 2.3
Step 3
(T-1) Allen key
(H-1) Cam Lock x 2 T-1
H-1
Follow arrow
direction
H-1
T-1
(H-1) Cam Lock x 8
x6
x2
T-1
H-1
H-1
T-1
DG-2
G-1
H
B
G-2 D
G-1
H
A
Front
Top
Install Cam Locks (H-1) into the corresponding holes along Back Support (B) as illustrated. Make sure arrows
on Cam Locks point to the Cam Screws (H-2) upon insertion. Secure all Cam Locks (H-1) using Allen Key
(T-1), turning them clockwise until they are snug. DO NOT OVER TIGHTEN the Cam Locks.
Top
Follow arrow
direction
Using a second person to assist you, carefully position Top Frame (A) onto the assembly, making sure it is
oriented correctly. Align all of the Cam Screws (H-2; installed in Step 1) with their corresponding holes in the
Back Support (B), Left/ Right Side Frames (G-1/G-2) and Divider Frame (H). Insert Cam Locks (H-1) into all
components as illustrated above. Ensure that the arrows on the Cam Locks (H-1) are all pointing toward their
corresponding Cam Screws (H-2). Once placed, fully tighten all Cam Locks (H-1) by turning clockwise using the
provided Allen Key (T-1) until snug. DO NOT over tighten. It is suggested to start tightening all Cam Locks (H-1)
starting on one side and making your way to the other side.
(T-1) Allen key
Front
Follow arrow direction
Follow arrow
direction

Step 4
Step 5
(H-12) Connector Bolt x 2
(H-13) Short Allen Bolt x 2
(H-14) Extra Large Flat Washer x 2
(T-1) Allen Key x 1
H-11
H-10
H-9
H-8
H-10
H-11
T-1
x8
E
Page 9
Top
(H-8) Medium Allen Bolt x 1
(H-9) Long Allen Bolt x 8
(H-10) Lock Washer x 9
(H-11) Medium Flat Washer x 9
(T-1) Allen Key x 1
H-13
H-14
H-12
L
T-1
E
F
D
G-1
H
G-2
M-1M-2
Position Base Frame 1 (E) and Base Frame 2 (F) on assembly as shown. Secure to the sides with Long Allen
Bolts (H-9), Lock Washers (H-10) and Medium Flat Washers (H-11) using provided Allen Key (T-1), stacking the
hardware in the order as shown. Ensure you are using the correct size hardware for each step. Secure Base
Frames 1&2 (E&F) with Medium Allen Bolt (H-8), Lock Washer (H-10) and Medium Flat Washer (H-11) using
provided Allen Key (T-1), stacking the hardware in the order as shown. Engage all bolts first, then fully tighten.
DO NOT over tighten.
B
Position Lids (L) to Left/Right Back Panels (M-1/M-2). Secure with Connector Bolts (H-12), Extra Large Flat
Washers (H-14), an Short Allen Bolts (H-13) using provided Allen Key (T-1), stacking the hardware through Back
Panels in the order as shown. Engage all bolts first then fully tighten. DO NOT over tighten.
Front
Front
IMPORTANT:
Please make note of the
different hardware sizes
and ensure you are using
the correct size hardware
(bolts, screws, and
washers) for each step.
x2

Step 6
(H-5) Short Pan Head Screw x 24
(T-3) Phillips Screwdriver
(H-15) Handle Bolt x 8
(H-16) Small Flat Washer x 8
x8
K
Page 10
H-15
H-16
T-3
Top
Position Left Back Panel (M-1) and Right Back Panel (M-2) onto assembly as shown. Make sure both panels are
oriented correctly (Connecting Bolt from previous step should point toward the top). Secure around the perimeter
of the cabinet with Short Pan Head Screws (H-5) using Phillips Screwdriver (T-3; not included). DO NOT over
tighten. Secure the middle of the Left/Right Back Panels (M-1/M-2) to the back of the assembly with Long Pan
Head Screws (H-6) and Large Flat Washers (H-7) using Phillips Screwdriver (T-3; not included), stacking the
hardware in the order as shown. DO NOT over tighten. Check that the Sideboard is square (90 degree) using
the Triangle (T-3).
Position Handles (K) to Left/ Right Doors A/ B (J-1/ J-2/ J-3/ J-4), ensuring the handle is oriented to the front of
the door. Secure each Handle (K) with Handle Bolts (H-15) and Flat Washers (H-16) using Phillips Screwdriver
(T-2; not included), stacking the hardware in the order as shown. DO NOT over tighten.
NOTE: All glass in tempered.
(T-3) Phillips Screwdriver
J-2
(H-7) Large Flat Washer x 4
(H-6) Long Pan Head Screw x 4
J-1
Top
Step 7
Front
Front
Triangle
90°
T-2
H-5
H-7
M-1
T-3
M-2
T-3
H-6
x24
x4
(T-2) Triangle
M-1
M-2