World Market Avila 602536 User manual

Page 1
THANK YOU FOR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
Avila Dining Bench
SKU-602536
Assembly Instructions
NOT FOR COMMERCIAL USE.

Page 2
Component List
LABEL PICTURE
ABench Top 1
B
C
Leg Post 2
D
Top Stretcher 1
1
Bottom Stretcher
DESCRIPTION QTY

LABEL PICTURE DESCRIPTION QTY
H-1
T-1
Spring Washer
Ø13 x M8
Flat Washer
Ø17 x M8
Short Allen Bolt
M6 x 45mm
Allen Key
15
1
Hardware List
Tool List
LABEL PICTURE DESCRIPTION QTY
H-2
H-3
13
2
H-4 6
H-5 10
T-2 1
H-6 Medium Allen Bolt
M6 x 60mm
Connector Plate
Page 3
Long Allen Bolt
M6 x 70mm
H-7
Screw
M6 x 19 mm
Phillips Screw driver
( Not Included )
3
2

Page 4
Assembly Preparation
Before Beginning :
A
B
D
H-1
H-2
H-3
H-4
H-5
H-6
H-7
•Unpack all hardware bags and components to ensure you have all parts-
•Read instructions, cover to cover-
•Have 2 adults on hand for assembly-
•Do not assemble on flooring or carpet-
•Assemble on a clean non-marring surface (packing foam)-
•Save all packaging until finished-
•In case of missing parts, please contact your nearest Cost Plus World
Market store or call our customer service call center at call 1-877-967-5362.
T-1
x 15
x 13
x 2
x 6
x 10
x 3
x 2
x 1
C
B

Page 5
Assembly Steps
STEP 1 : Attaching Bottom Stretcher
H-1 Spring Washer (∅13xM8) x 2
H-5
H-3 Connector Plate x 2
Short Allen Bolt (M6x45) x 2
H-4 Screws (∅6 x 3/4 Inch) x 6
D
B
T-1
T-2
H-5
H-4
H-1
STEP 2 : Assembling Bottom Stretcher
B
D
B
B
2X
Using a second person to assist you, place both Leg Posts (B) upside down onto a padded, non-marring surface
as shown. Insert Bottom Stretcher (D) into the corresponding notched hole in the bottom of Leg Post (B) .
Align Connector Plate (H-3) with the corresponding pre-drilled holes on the bottom of each Leg Base (B) as shown.
Start by securing the middle hole of the Connector Plate (H-3) which will also secure the Bottom Stretcher (D) using
Short Allen Bolts (H-5) and Spring Washers (H-1). Engage the bolts by hand, but do not fully tighten them yet.
Next, finish securing Connector Plate (H-3) using Screws (H-4) and a Phillips head screwdriver (not include). Fully
tighten all screws at this time using a Phillips head screwdriver. Then Fully tighten Short Allen bolts ( H-5) using
Allen Key ( T-1)
TOP
TOP
H-3

Page 6
Assembly Steps
STEP 3 : Attaching Top Stretcher
STEP 4 : Attaching Bench Top
C
B
H-1
H-2
Spring Washer (∅13xM8) x 2
Flat Washer (∅17x M8) x 2
H-7 Long Allen Bolt (M6 x 70) x 2
2X
B
D
T-1
H-7 H-1
H-2
H-1
H-2
Spring Washer (∅13xM8) x 11
Flat Washer (∅17x M8) x 11
H-5 Short Allen Bolt (M6 x 45) x 8
H-6
Medium Allen Bolt (M6 x 60) x 3
Using a second person to assist you, turn the assembly ( from Step 2 ) upright as shown. Attach Top Stretcher (C)
to both Leg Posts (B) and secure using Long Allen Bolts (H-7), Spring Washers (H-1) and Flat Washers (H-2),
stacking the hardware in the order shown. Engage bolts by hand but do not fully tighten them yet.
TOP
H-1
H-2
H-5
T-1
T-1
H-6
H-1
H-2
B
B
A
2X 3X
Lay the Table Top (A) up side down on non-marring surfaces. Using a second person to assist you, turn the
assembly ( from Step 3 ) up side down. Align the holes on Leg Posts (B) with corresponding holes on Table Top (A)
and secure using Short Allen Bolts (H-5), Spring Washers (H-1) and Flat Washers (H-2), stacking the hardware in
the order shown. Then secure Top Stretcher to the Table Top (A) using Medium Allen Bolts (H-6), Spring Washer
(H-1), and Flat Washer (H-2), stacking the hardware in the order shown. Engage bolts by hand , once all bolts have
been inserted then fully tighten using Allen Key (T-1). including bolts from step 3
TOP

Page 7
Assembly Steps
STEP 5
Using a second person to assist you, turn the assembly ( from Step 4 ) upright as shown.
Congratulations, the Assembly is now complete and the product is ready for use

Page 8
Care & Maintenance