World Market Keya 607437 User manual

Keya Cabinet
SKU - 607437
R
Page 1
NOT FOR COMMERCIAL USE
Anti-Tip Measures & Knob Assembly
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS PERTAINING
TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877- 967-5362 FOR ASSISTANCE.

Label Picture Description Qty
A1
Cabinet
Page 2
BHandle Knob
(Pre-attached) 2
Hardware List
Label Picture Description Qty
H-1 2
Tool List
Label Picture Description Qty
T-1
Phillip head
screw driver
Pan Head Screw
(M4 x 25 mm)
(Not
Included)

Assembly Preparation
Before beginning:
Page 3
V·
�
f2xi •

b-
0-








W  M 
 1  .

Ribbon
!
WARNING
Serious or fatal crushing injuries can occur
from furniture tipover. To help prevent
tipover:
-Install tipover restraint provided.
-Do not set TV's or other heavy objects on the
top of this product, unless the product is
specifically designed to accommodate them.
-NEVER allow children to climb or hang on
drawers, door, or Shelves.
-Keep remote controls, toys and other items
that might attaract children off this product
Use of tipover restraints may only reduce,
but not eliminate, the risk of tipover.
This is a permanent label. Do not remove!
KNOB ASSEMBLY:
Using a second person to assist, carefully turn the assembly upright so that it rests evenly on the legs. Next, carefully
open the doors by pulling on the pre-installed ribbon as shown. Unscrew the Pan Head Screw (H-1) and Handle
Knobs (B) from the interior of the door using a Phillips head screwdriver (not included). Discard the ribbon. Once
both Handle Knobs (B) have been removed, reinstall them on the FRONT of the doors using the same pan head screw
hardware and Phillips head screwdriver. Turn the screwdriver (T-1) clockwise until the screw is snug and make sure the
Handle Knobs (B) are upright and level on the front of the door assembly.
Page 4
B

ϰdžƌĂĐŬĞƚ
!"#$ %
&'()"* +
6DIHW\6WUDS$WWDFKPHQW
A. Mark the location of the hole on the wall using bracket (A) approx 1" below the top of furniture.
Predrill the holes at marked location & insert wall anchors (E). Align bracket onto wall anchors & secure
using long screws (B).
B. Move the furniture to its final position against the wall and mark the location of the wall bracket on
the back of the furniture. The bracket that attaches to the furniture must go into the solid wood piece at
the top, not into the thinner back panel. Move the furniture away from the wall and place a bracket (A) on
the mark. Mark and drill holes for the screws using a 3/32" drill bit. Attach the bracket to the furniture
using the short screws (C).
C. Move the furniture to its final position, and align the bracket on the furniture with the bracket on the
wall. Thread the strap (D) through the bracket as shown, and tighten until snug. Do not overtighten.
Important: Check that the wall bracket is firmly screwed into the stud, the furniture bracket is firmly
attached to the frame, and the strap is snug.
ϰdžtĂůůŶĐŚŽƌ
ϰdž>ŽŶŐƐĐƌĞǁ
ϰdž^ŚŽƌƚƐĐƌĞǁ
Ϯdž^ƚƌĂƉ
Page 5

Care & Maintenance



}} s
- •
A •


L 
 
 

Page 6