6Buy Online! Wurtec.com Buy Online! Wurtec.com 7
Quick Set-Up (from onboard keypad)
Programming Phone Numbers
(The number(s) you want the S3C to autodial)
STEP 1
Press the EMERG
PHONE
NUMB button on the keypad.
STEP 2
The phone will say “press 1 for rst number, 2 for second number, 3 for third
number.” Choose which number you want to enter. The phone will ask you to enter
the number followed by the #
VOL DN key. At this point enter the number you want the
phone to autodial and press the #
VOL DN key. Up to 24 digits can be programmed into
the phone. See page 10 for ring-down programming.
STEP 3
Once the number is programmed, the phone will recite the number. If the number
is correct and you are nished you may press VOL UP then 0to exit program mode.
If you have another number to program the phone will automatically revert back to
the phone number program menu and you will hear an option to program phone
numbers 2 and 3, follow the same steps to program those numbers if you choose to
do so. Note: The rst number will dial for 30 seconds, the second number will dial
for 60 seconds, and the third number will dial for 120 seconds.
Programming Site Identication Message
STEP 1
Press the SITE ID
MSG button on the keypad.
STEP 2
Press
1 to record. The phone will say “at the tone, record your message followed
by #
VOL DN . After you heard the tone, record the message and press the #
VOL DN key
when nished. A typical message consists of the address, name of the building the
elevator is in, and the elevator number if more than one elevator is present, and a
call back number. The site identication message should not exceed 16 seconds.
STEP 3
If the message that has been recorded is correct you may
press VOL UP then 0to exit programming mode. If the message is incorrect and
needs to be recorded again, follow the steps for programming the site identication
message again. The new recording will automatically overwrite the old recording.
You can repeat this process until the message is correct.
Quick Set-Up (from onboard keypad) cont.
Adjusting Onboard Volume
(volume of the programming menu voice)
STEP 1
To increase the volume of the onboard programming menu voice press the
TALK
/ END and VOL UP keys at the exact same time then release. You will hear a number (1-
8). Continue to press the TALK
/ END and VOL UP at the same time until the desired volume
is reached. The number will increase as the volume increases. The phone will say
“8” repeatedly once it has hit its maximum volume.
STEP 2
To decrease the volume of the onboard programming voice press the
TALK
/ END and #
VOL DN keys at the same time and then release. You will hear a number (1-
8). Continue to press and release the TALK
/ END and #
VOL DN keys until the desired volume is
reached. The number will decrease as the volume decreases. The phone will say
“1” repeatedly once it has reached its lowest volume.
Adjusting Conversation Volume
STEP 1
Be sure the phone is connected to a live telephone line and has either external
power connected or a 9V battery. If you have both the external power and a 9V
battery connected, be sure the battery is rechargeable, or it could result in a battery
malfunction and could damage the phone and or harm the installer.
STEP 2
To increase the volume of the person you are speaking to rst press the TALK
/ END
key. If you have a live telephone line, the phone will say “Please enter number to
be dialed” and then you will hear a standard dial tone. DO NOT dial a number.
Once you hear the dial tone, Press the TALK
/ END and VOL UP keys at the exact same time
and then release. You will hear your dial tone increase in volume and also hear
a number. Continue to press the TALK
/ END and VOL UP keys at the same time and then
release until the desired volume is reached. The number will increase with each
volume increase. The phone will say “8” once the maximum volume is reached.
When nished press TALK
/ END to hang up the phone. (continued on next page)
