Ooma Safety phone 700-0129-203 User manual

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

Quick Start Guide

700-0129-203 1 3 52 4 6 8

Package Contents

Introduction

The Ooma Safety Phone is a small speaker phone

that can be worn or kept by your side all day.

Since the Safety Phone is a fully-working speaker

phone capable of two-way communication, you can

use it to make and receive calls anywhere within the

range of your home Ooma system.

Comfortable to wear and programmable with up to

two speed dial numbers, the Safety Phone gives

you the peace of mind that your caretaker and loved

ones are just a button press away. The Safety Phone

can effectively support your independent lifestyle.

Important Information About the Safety Phone

•Carefully read and follow the instructions in this

Quick Start Guide, which may also be viewed

online at:

http://www.ooma.com/support/documentation

Do not use the Safety Phone if you cannot

understand and follow the instructions.

•Use of the Safety Phone requires high-speed

Internet access and the Ooma Telo device. The

Safety Phone will not work if either the Internet or

Ooma Telo are not functioning properly.

•The Safety Phone is intended for indoor use with a

range of up to 50 meters (164 feet) from the Ooma

Telo. This range may vary based on factors such

as home construction and other electrical devices

and appliances being used in the home.

•The battery in the Safety Phone is not replaceable.

The expected lifetime of the battery is two years,

but may vary based on usage.

•Do not use the Safety Phone if you have an

implanted cardiac pacemaker.

Charging cradle with AC adapter

Microphone

Status LED

Changes color and blinks

to indicate the status of

the Safety Phone.

Talk

Press to place a call, and

again to end the call.

Press and hold to power the

Safety Phone on or off.

Speaker

Volume Up

Press to increase earpiece

or ringer volume.

Volume Down

Press to decrease earpiece

or ringer volume.

Speed Dial Buttons

Charge Phone Register Phone Program Speed Dial Online Quick Reference Guide

Place the Safety Phone on the charging cradle

and charge for a few minutes until the status

LED turns purple and you start to hear the Safety

Phone play two short beeps periodically.

When you are ready to register the phone, take

it out of the cradle and put it back in. The status

LED will start to blink red and blue.

Press and hold the PAGE button on your Ooma

device for three seconds to activate registration

mode.

The Safety Phone will now register with your

Ooma system. When the registration process

is successful, you will hear a long beep.

Continue to charge the Safety Phone for at

least three hours until the status LED lights up

solid blue.

Front

Back

Finish the installation process by going to:

http://my.ooma.com/devices

Here you will be able to program the two

speed dial buttons.

Step 1 Step 2 Step 3

Ooma Safety Phone with lanyard

Breakway

connector

WARNING: To avoid injury,

please review the Important Safety

Information section on page 11

before using the Safety Phone.

Operation Instructions

•Powering the Safety Phone on or off

To power the phone on or off, press and hold the

TALK button until you hear three short beeps.

•Making an outgoing call

Outgoing calls can be placed to either of the two

pre-programmed speed dial buttons. Press the

appropriate button to call the programmed number.

•Answering a call

Answer incoming calls by pressing the TALK button.

•Ending a call

To end a call, press the TALK button again while

on a call. You can also end a call by putting the

Safety Phone back onto the charging cradle.

•Adjusting the volume

The speaker volume can be adjusted up by pressing

the VOLUME UP or VOLUME DOWN button during

a call. Use the same buttons to adjust the ringer

volume when the phone is in idle mode.

•Registering to a new base unit

by pressing and holding the VOLUME UP and

VOLUME DOWN buttons at the same time until the

status LED toggles between red and blue.

• Thephoneisdesignedforbody-wornoperationandmeetsFCCRFexposure

guidelines when used with any belt clip, carrying case, or other accessory

supplied with this product. (All necessary accessories are included in

the package; any additional or optional accessories are not required for

compliance with the guidelines.) Third party accessories (unless approved by

the manufacturer) should be avoided as these might not comply with FCC RF

exposure guidelines.

Industry Canada (I.C.) Notice

Terminal equipment

NOTICE: This equipment meets the applicable Industry Canada Terminal

EquipmentTechnicalSpecications.Thisisconrmedbytheregistrationnumber.

TheabbreviationICbeforetheregistrationnumbersigniesthatregistration

was performed based on a Declaration of Conformity indicating that Industry

Canadatechnicalspecicationsweremet.ItdoesnotimplythatIndustryCanada

approved the equipment.

Radio equipment

ThetermICbeforetheradiocerticationnumberonlysigniesthatIndustry

Canadatechnicalspecicationsweremet.Operationissubjecttothefollowing

two conditions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired

operation of the device. “Privacy of communications may not be ensured when

using this telephone”.

IC Number: 1135B-80949600

written permission is prohibited. Ooma, the Ooma logo, Ooma Telo, Ooma Safety

Phone and all other Ooma company, product and service names and slogans

are trademarks of Ooma, Inc. All other product, service or brand names are the

property of their respective owners. Patent pending.

Compliance Information

Anychangesormodicationstothisproductnotexpresslyapprovedbythe

manufacturer or other party responsible for compliance could void your authority

to operate this product.

FCC Part 15 Information

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including interference that may

cause undesired operation. Privacy of communications may not be ensured when

using this phone.

FCC PART 15.105(b): Note: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthat

to which the receiver is connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

RF Exposure Information

This product complies with FCC radiation exposure limits under the

following conditions:

• Thebasemustbeplacedtoallowaminimumof20cm(8inches)betweenthe

antenna and all persons during normal operation.

• Thebasemustnotbecollocatedoroperatedinconjunctionwithanyother

antenna or transmitter.

What this Warranty Covers. Ooma agrees to provide a limited warranty to the

holder of a valid proof of purchase (“Consumer” or “you”) that the Ooma Safety

Phone contained in this package (“Product”) is free from material defects in

material and workmanship, subject to the exclusions noted below. This limited

warranty extends only to the Consumer for Products purchased and used in the

United States of America or Canada.

What Ooma Will Do. During the warranty period, Ooma or its authorized service

representative will repair or replace, at its option, without charge, a Product which

is found to be materially defective in materials or workmanship and returned to

Ooma. Ooma, at its option, may use new or refurbished replacement parts to

repair the Product, or may replace the Product with a new or refurbished product

having the same or similar function.

How Long this Warranty Lasts. This limited warranty shall expire one (1) year

from the date of the Product purchase. Replacement or refurbished parts and

products are warranted for the original Product warranty period. This warranty

terminates if you sell or transfer your Product.

What this Warranty Excludes.

This limited warranty does not cover: (a) the cost

of shipping and handling for returned and replacement products, or damage or

loss during shipment for warranty service; or (b) any software (which is governed

exclusively by the licensing terms of such software); or (c) any Product that

has been subjected to misuse, accident, shipping or other physical damage,

improper installation, abnormal operation or handling that is contrary to operation

instructions,neglect,actsofgod,inundation,re,waterorotherliquidintrusion,or

force majeure; or (d) any Product that has been damaged due to repair, alteration,

ormodicationbyanyoneotherthananauthorizedservicerepresentativeof

Ooma; or (e) any Product to the extent that the problem experienced is caused

by signal conditions, network reliability or cable or antenna systems; or (f) any

Product whose identifying information has been removed, altered or rendered

illegible; or (g) any Product purchased, used, serviced, or shipped for repair from

outside the United States or Canada, or that is returned without a valid proof

of purchase; or (h) any indirect or consequential harm caused as a result of any

defect or failure of the Product to properly operate, including without limitation lost

data or inability to communicate.

How to Get Warranty Service. To obtain warranty service, call

Customer

Support toll-free at 1-888-711-6662 (USA) or 1-866-929-6662

(Canada) for detailed

information, including instructions on how and where to return your Product and

on any applicable costs associated with a repair, replacement or exchange. You

may be required to provide proof of purchase before obtaining warranty service,

and it is your sole responsibility to maintain such proof (e.g., a sales receipt).

Returned products that are determined not to be materially defective will be

subject to a handling fee. If you disagree with any of our decisions with respect to

warranty service, you have the right to contest that decision as permitted under

applicable laws and regulations.

How State Law Applies.Thislimitedwarrantygivesyouspeciclegalrights.You

may also have other rights which vary from state to state.

Warranty Disclaimer and Limitation on Liability. THIS WARRANTY IS THE

COMPLETEANDEXCLUSIVEWARRANTYAGREEMENTFORTHEOOMA

SAFETY PHONE BETWEEN YOU AND OOMA. NO ONE IS AUTHORIZED TO

MAKE MODIFICATIONS TO THIS LIMITED WARRANTY AND YOU SHOULD

NOTRELYONANYSUCHMODIFICATION.OOMARESERVESTHERIGHTTO

CHANGE ITS LIMITED WARRANTY WITHOUT PRIOR NOTICE FOR FUTURE

SALES. OOMA DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO ITS

PRODUCTS, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE,

INCLUDING WITHOUT LIMITATION, COURSE OF DEALING, TRADE USAGE

OR PRACTICE OR THE WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE, TITLE, OR NON-INFRINGEMENT OF THIRD

PARTYRIGHTS.MOREOVER,OOMASHALLNOTBELIABLEFORINDIRECT,

INCIDENTAL,SPECIAL,EXEMPLARY,PUNITIVE,ORCONSEQUENTIAL

DAMAGES OF ANY NATURE ARISING OUT OF, OR IN CONNECTION WITH, THE

LIMITED WARRANTY OR THE USE OR PERFORMANCE OF ANY PRODUCT,

WHETHER BASED ON CONTRACT OR TORT, INCLUDING NEGLIGENCE,

ORANYOTHERLEGALTHEORY,EVENIFWEHAVEBEENADVISEDOFTHE

POSSIBILITY OF SUCH DAMAGES. THE TOTAL AGGREGATE LIABILITY BY

OOMA FOR DAMAGES OF ANY NATURE, REGARDLESS OF FORM, ACTION OR

FORESEEABILITY,SHALLINNOEVENTEXCEEDTHEAMOUNTPAIDBYYOU

TO US FOR THE OOMA SAFETY PHONE UPON WHICH LIABILITY IS BASED.

SOMESTATESAND/ORCOUNTRIESDONOTALLOWLIMITATIONSON

HOWLONGANIMPLIEDWARRANTYLASTS,AND/ORDONOTALLOWTHE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,

SOTHEABOVELIMITATIONSAND/OREXCLUSIONSMAYNOTAPPLYTO

YOU. IF SUCH IS THE CASE, TO THE EXTENT PERMITTED BY APPLICABLE

LAW, OOMA LIMITS THE DURATION OF ANY IMPLIED WARRANTIES TO THE

DURATION OF THIS EXPRESS LIMITED WARRANTY.

Disclaimer of Liability and Indemnication: YOU UNDERSTAND AND

AGREE THAT OOMA IS NOT RESPONSIBLE, AND DISCLAIMS ALL LIABILITY

FOR, RELATED TO, OR ARISING OUT OF, YOUR FAILURE TO (I) CHARGE

THE OOMA SAFETY PHONE, (II) REGISTER THE OOMA SAFETY PHONE,

(III) ENTER IN THE CORRECT INFORMATION WHILE PROGRAMMING

THEOOMASAFETYPHONEONLINE,OR(IV)TESTTHEFUNCTIONAND

RANGEOFTHEOOMASAFETYPHONEANDTHEOOMASERVICES.WE

DONOTHAVEANYCONTROLOVERWHETHER,ORTHEMANNERIN

WHICH,CALLSUSINGOUR911DIALINGSERVICEAREANSWEREDOR

ADDRESSED BY ANY EMERGENCY RESPONSE CENTER. WE DISCLAIM

ALL RESPONSIBILITY FOR THE ABILITY OF THE OOMA SAFETY PHONE TO

CONNECT TO AN EMERGENCY RESPONSE CENTER, THE CONDUCT OF

THE EMERGENCY RESPONSE CENTER AND THE NATIONAL EMERGENCY

CALLING CENTER. WE RELY ON THIRD PARTIES TO ASSIST US IN ROUTING

911 CALLS TO EMERGENCY RESPONSE CENTERS AND TO A NATIONAL

EMERGENCY CALLING CENTER. WE DISCLAIM ANY AND ALL LIABILITY

ORRESPONSIBILITYINTHEEVENTSUCHTHIRDPARTYDATAUSEDTO

ROUTE CALLS IS INCORRECT OR YIELDS AN ERRONEOUS RESULT. WE DO

NOTHAVEANYCONTROLOVERTHEACTIONSOROMISSIONSOFYOUR

ALERT CONTACTS (AS PROGRAMMED BY YOU UPON REGISTRATION OR

THEREAFTER), OR THE INTERNET CONNECTION OR MOBILE TELEPHONE

CARRIERSERVICESUTILIZEDBYYOUORYOURALERTCONTACTS.NEITHER

OOMA NOR ITS OFFICERS OR EMPLOYEES MAY BE HELD LIABLE FOR ANY

CLAIM,DAMAGE,ORLOSS,ANDYOUHEREBYWAIVEANYANDALLSUCH

CLAIMS OR CAUSES OF ACTION, ARISING FROM OR RELATING TO OUR 911

DIALINGSERVICES.YOUSHALLDEFEND,INDEMNIFY,ANDHOLDHARMLESS

OOMA, ITS OFFICERS, DIRECTORS, EMPLOYEES, AFFILIATES, AGENTS, AND

ASSIGNS,ANDANYOTHERSERVICEPROVIDERWHOFURNISHESSERVICES

TOYOUINCONNECTIONWITHTHEOOMASAFETYPHONEORSERVICES,

FROM ANY AND ALL CLAIMS, LOSSES, DAMAGES, FINES, PENALTIES,

COSTS, AND EXPENSES (INCLUDING, WITHOUT LIMITATION, ATTORNEYS’

FEES) BY, OR ON BEHALF OF, YOU OR ANY THIRD PARTY RELATING TO

THE ABSENCE, FAILURE, OR OUTAGE OF THE OOMA SAFETY PHONE OR

OOMASERVICE,INCLUDING911DIALINGAND911ALERTS,INCORRECTLY

ROUTED 911 DIALING CALLS AND INCORRECTLY ROUTED ALERT EMAILS OR

TEXT MESSAGES, INCORRECTLY ENTERED EMAIL ADDRESSES OR MOBILE

TELEPHONENUMBERSFORTHEALERTCONTACTS,AND/ORTHEINABILITY

OF ANY USER OF THE OOMA SAFETY PHONE TO BE ABLE TO USE OOMA

SERVICE,911DIALING,911ALERTS,ORACCESSEMERGENCYSERVICE

PERSONNEL. IF YOU ARE NOT COMFORTABLE WITH THE LIMITATIONS OF

THE911DIALINGSERVICE,YOUSHOULDHAVEANALTERNATIVEMEANS

OFACCESSINGTRADITIONAL911SERVICES.IFYOUARENOTCOMFORTABLE

WITHTHELIMITATIONSOFTHEOOMASAFETYPHONE,OOMASERVICE,911

DIALING,OR911ALERTSSERVICE,YOUSHOULDNOTENABLEAND/ORUSE

THE OOMA SAFETY PHONE.

Important Safety Information Limited Warranty

Online knowledgebase: www.ooma.com/support

User manuals: www.ooma.com/userguide

Community forum: forums.ooma.com

Live customer care: 1-888-711-6662 (US)

1-866-929-6662 (Canada)

Need Assistance?

Check out these resources for troubleshooting

guides or additional help:

LED Indicators

The status LED on the Ooma Safety Phone can

communicate information about the connection and

battery status of the device. The table below shows

the different indicator patterns that the phone uses:

Audio Indicators

The Ooma Safety Phone also uses audio indicators

to communicate changes in the device status. See

below for a table of audio prompts:

910 12 14 15 1611 13 17

Purple Steady Phone is unregistered

Flashing Phone is registered, but it

cannot connect to your Ooma

system (searching or out

of range)

Blue Steady Phone is seated in the charging

cradle and fully charged.

 Longashing Phoneisinidlemodeandnot

charging.

Doubleashing

Phone is on and connected to

a phone call.

Continuously Phone is ringing.

 ashing

Red Steady Phone is charging on its cradle.

Flashing Battery is low and the phone

needs to be returned to its

charging cradle.

Doubleashing

Phone is in use and the battery

is low.

 Tripleashing Phoneispoweringoff.

Red/Blue Toggling Phone is in registration mode.

Long beep The phone has successfully registered

to your Ooma system.

Two short beeps Battery is low and the phone must be

returned to charging cradle.

Three short beeps

The phone is on but the signal is weak.

 Phoneispoweringon/off.

WARNING: Failure to follow these safety

instructions could result in re, electric shock,

or other injuries, or damage to the Ooma Safety

Phone or other property. The Safety Phone and

its accessories must be operated only for its

intended use and not for any other purposes.

Read all the safety information below before

using the Ooma Safety Phone.

•This product contains a non-replaceable lithium-

ionbattery.Thereisriskofexplosion,re,burnor

leaking which can be caused by improper charging,

shorting of the battery, or other misuse. Always

use the charger provided with the product.

DO NOT attempt to disassemble, replace, or

otherwise attempt to access the battery.

•This unit is NOT waterproof. DO NOT expose

this product to water, rain, moisture, other liquids

(alcohol, etc.) or submerse in water or other liquids

for any reason. DO NOT bath or shower while

wearing or using this product.

•DO NOT bath or shower while wearing or using this

product. DO NOT use this product near water, for

example, near a wash bowl, kitchen sink or laundry

tub, in a wet basement or near a swimming pool.

•Objects worn around the neck may pose a risk of

injury, including strangulation. Use the lanyard with

caution. DO NOT attempt to disable the break-away

feature on the lanyard as this may increase the risk

of injury. Keep the lanyard away from children.

•Avoid using this product during an electrical storm.

There may be a remote risk of electric shock

from lightning.

•DO NOT use this product to report a gas leak in the

vicinity of the leak.

•DO NOT use this product if you have an implanted

cardiac pacemaker.