WY'EAST MEDICAL VISTA 400 User manual

REMOVABLE FOOT PLATE
Removable footplate for
AMBULATION.
51924-R01
Squeeze the yellow bar &
push down/pull up to activate
pneumatic stand assist.
Step on yellow pedals to close
and open legs to go around
chairs & ambulate.
Adjustable seat pad
configurations.
Pull yellow levers to adjust
clamp. Turn to loosen and
tighten adjustable shin pad.
800.255.3126 | wyeastmedical.com
VISTA400
Instructions For Use

A
B
1
2
3
4
5
6
7
8
10
11
9
VISTA QUICK REFERENCE GUIDE
READ USERS MANUAL BEFORE OPERATING
LOCK WHEELS
Position Standing
Aid to Patient
Open Legs and Seats
As Needed
Position Patient’s
Feet in Footrest
Position Shin Support Against Shins
Secure clamp A
Support
Must Be
Below
Knee
Joint
Transport Patient
Have Patient Grasp
Handlebar and Stand
Position Seats Under Patient
and Have Patient Sit
Adjust Shin Vertical Support
Secure clamp B
All Yellow Areas
on Equipment
Are Adjustable
UNLOCK WHEELS
Adjust Sitting Height

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 1 of 17
VISTA
Operator’s Manual
OPERATOR’S MANUAL
VISTA
NON-POWERED STAND AID
Model No. 51871

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 2 of 17
VISTA
Operator’s Manual
WARRANTY
Wy’East Medical Corporation (Wy’East) warrants to the original user the Vista Non-Powered Stand
Aid manufactured by the company is free from defects in material and workmanship under normal use
and service. The term of warranty from the date of product receipt is for a period of two (2) years on
mechanical lift components, one (1) year on electronic components, and one (1) year for the battery.
During this term Wy’East will provide to the user, at Wy’East’s option, new or repaired replacement
components.
In order to initiate a warranty claim, original user must notify Wy’East within the applicable warranty
period specifying the nature of the claim. Wy’East will issue instructions as to the procedure to
follow. Wy’East reserves the right to confirm the existence of any claimed defect and to determine
whether any damage was caused by neglect, misuse, unauthorized alteration or failure to follow
maintenance instructions. With respect to a claim covered by this warranty, the defective part will be
replaced or repaired at no charge, provided the defective part is returned to Wy’East. The user has
the responsibility for installation. Assistance is available by calling (503) 657-3101 or through email
at info@wyeastmed.com. This is the exclusive remedy for a claim under this warranty and in no event
shall Wy’East be liable for consequential damages. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES EXPRESSED OR IMPLIED.
PLEASE
Read this entire manual before operating the Vista Non-Powered Stand Aid.
This warranty applies to the Wy’East Vista Non-Powered Stand Aid only.
For questions or information regarding the Vista Non-Powered Stand Aid, contact:
Wy’East Medical Corporation
16700 SE 120th Ave.
Clackamas, OR 97015, USA
(503) 657-3101
(800) 255-3126
wyeastmedical.com
info@wyeastmed.com

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 3 of 17
VISTA
Operator’s Manual
MAINTENANCE
& ASSISTANCE
INTRODUCTION
Contents
HOW TO USE THIS MANUAL:_________________________________________________ 4
DEFINITIONS: ______________________________________________________________ 4
SAFETY CONSIDERATIONS FOR ALL PROCEDURES: ____________________________ 6
PRIOR TO FIRST USE:_______________________________________________________ 6
FEATURES: ________________________________________________________________ 7
Install/Uninstall Footrest: __________________________________________________ 7
Shin Guard Cam Lever: ___________________________________________________ 7
Shin Guard Adjustment Toward/Away from Patient: ____________________________ 7
Shin Guard Adjustment Up/Down: __________________________________________ 7
Seat Position: Up ________________________________________________________ 8
Seat Position: Out________________________________________________________ 8
Seat Position: Up and Out _________________________________________________ 8
Seat Height Adjustment: __________________________________________________ 9
Legs Open/Close Function:________________________________________________ 9
OPERATING THE VISTA NON-POWERED STAND AID: ____________________________ 10
TECHNICAL SPECIFICATIONS: ________________________________________________ 12
PERIODIC MAINTENANCE:___________________________________________________ 13
ONCE A MONTH ________________________________________________________ 13
TROUBLESHOOTING: _______________________________________________________ 13
FACTORY ASSISTANCE: _____________________________________________________ 14
REPLACEMENT ITEMS:___________________________________________________ 14
RETURNING ITEMS: _____________________________________________________ 14
REPLACEMENT PARTS: _____________________________________________________ 15
NOTES: ___________________________________________________________________ 16
CONTACT INFORMATION ____________________________________________________ 17

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 4 of 17
VISTA
Operator’s Manual
INTRODUCTION
HOW TO USE THIS MANUAL:
This manual is designed to familiarize you with the operation of the Vista Non-Powered Stand Aid. Read it
thoroughly before using or servicing the equipment. Keep the manual for future reference and for new members
of your staff.
DO NOT ATTEMPT TO USE EQUIPMENT WITHOUT UNDERSTANDING THIS MANUAL
To ensure safe operation, read carefully the entire manual, before installing, operating, or servicing this
equipment.
If anything is not completely understood, please contact your supplier for more details. Failure to comply with
warnings in this manual may result in injury.
Keep this manual with the Vista Non-Powered Stand Aid and refer to it as required. Contents of this manual are
subject to change without prior notice to users.
DEFINITIONS:
The words WARNING, CAUTION, and NOTE carry specific meanings and should be carefully reviewed.
WARNING: The personal safety of the patient or user may be involved. Disregarding this information could result
in injury to the patient or user.
CAUTION: These instructions point out special procedures or precautions that must be followed to avoid
damaging the Vista.
NOTE: This provides special information to make maintenance easier or important instructions more clear.
MEANING OF SYMBOLS
Caution Safe working load (SWL)
Consult instructions for use (IFU) Do not step on surface
Important
Consistent with our policy of continuing product
improvement, WY’EAST MEDICAL CORPORATION
reserves the right to change these specifications
without notice or obligation.

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 5 of 17
VISTA
Operator’s Manual
Your Vista Non-Powered Stand Aid is designed for assisting patients with weight bearing ability to
stand and transfer.
• Bed to Chair transfer.
• Wheelchair repositioning.
• Easy access for wheelchair.
• Total adjustability for convenience and usability.
• Sturdy dependability.
The Vista has a compact footprint allowing for greater maneuverability in tight spaces.
Intended for use in acute care, long-term care, outpatient care, and home care. It is not
recommended for use in a shower.
Prior to using the Vista for transfer or any other procedure, the patient must be
assessed by a qualified professional to determine the suitability of using the Vista with
that patient. Patients should be partial weight bearing, have upper body strength and be
able to follow instructions.
With the footrest removed the Vista can be used to assist in weight bearing
rehabilitation and balance training.

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 6 of 17
VISTA
Operator’s Manual
SAFETY CONSIDERATIONS FOR ALL PROCEDURES:
1. The Vista is designed to be used ONLY on level surfaces.
2. ALWAYS lock the wheels while positioning the patient.
3. Prior to using the Vista for transfer, the patient must be assessed by a qualified professional to
determine the suitability of using the Vista with that patient.
4. Never leave the patient unattended while in the Vista, or during any portion of the transfer
procedure.
5. Ensure the patient is properly seated in the Vista before transporting. Never transport a
patient while they are standing in the Vista.
6. Never exceed the safe working load. SWL is 400 lbs.
7. Do not power wash the Vista.
8. When cleaning and disinfecting, use a 5.25% chlorine bleach dilution and an EPA registered
Hard Surface Disinfectant on painted and plastic surfaces. On all other surfaces use an EPA
registered Hard Surface disinfectant wipe that does not contain sodium hypochlorite (bleach).
9. Warranty applies only if repairs or alterations are performed by an authorized technician.
PRIOR TO FIRST USE:
If any individual parts are suspected to be damaged, do not operate the parts, but
return them for inspection/service.

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 7 of 17
VISTA
Operator’s Manual
FEATURES:
Install/Uninstall Footrest:
To remove the footrest, lift up by holding the yellow cross
bar and handle (see Fig.1).
a. Raise the footrest 2 inches vertically.
b. Remove as shown.
Shin Guard Cam Lever:
1. To clamp, rotate the lever clockwise.
2. To re-position the lever at an angle to allow clamping,
pull the yellow handle back (see Fig. 2a), rotate to
desired position (see Fig. 2b) and release.
3. You are now ready to rotate to clamp.
Shin Guard Adjustment Toward/Away from Patient:
Adjust shin guard to ensure that shin guard rests against the
patient’s shins while patient is sitting with lower leg at 90° to
thigh where the thigh is parallel with the floor.
Shin Guard Adjustment Up/Down:
Adjust shin guard to ensure that the top of the shin guard is
at least 2 inches below the patient’s patella to avoid injury.
Figure 1
Figure 2bFigure 2a

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 8 of 17
VISTA
Operator’s Manual
Seat Position: Up
To move seat up, pull up and rotate seat as shown.
Seat Position: Out
To move seat out, push up on yellow knuckle and rotate seat
as shown.
Seat Position: Up and Out
To move seat up and out, follow the instructions for the two
previous features.
FEATURES:

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 9 of 17
VISTA
Operator’s Manual
Seat Height Adjustment:
To lower or raise the seat height, squeeze the yellow lever
and pull up or push down on the handlebar.
NOTE: Adding weight on the seat pads can aid in height
adjustment.
Legs Open/Close Function:
1. Push down on the left yellow pedal to open legs.
2. Push down on the right yellow pedal to close legs.
Allows clearance for the caregiver to get around a chair,
wheelchair or commode and properly place the feet and set
the shin guard.
FEATURES:

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 10 of 17
VISTA
Operator’s Manual
OPERATING THE VISTA NON-POWERED STAND AID:
1. ENSURE patient is able to sit in an upright posture and the Vista is able to be positioned in front of
the patient as shown (Fig. 3).
2. Move the SEATS out and OPEN the LEGS of the Vista to an appropriate width to maneuver the Vista
around a chair or wheelchair (Fig. 3).
3. Move the Vista toward patient until their feet are completely supported by the footrest and their legs
are in a position as close to 90 degrees as possible (Fig. 4).
4. LOCK the rear WHEELS.
Figure 3 Figure 4
5. Move shin guard forward to rest against the patients shins. Lock Cam Lever.
6. Adjust the shin guard until it rests 2 or more inches below the patients knees (patellae). This prevents
the patient’s kneecaps being pushed upward when they stand up.
7. Instruct the patient to grab the handle bar.
8. CHECK the patients’ body alignment prior to having them stand. Ensuring that the patient and the
Vista are in alignment with each other will help alleviate any feelings of being off balance during the
transfer.
90°

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 11 of 17
VISTA
Operator’s Manual
9. Instruct the patient to stand up (Fig. 5).
10. Position the seats under the patient and have them sit (Fig. 6).
11. Adjust SEAT height by squeezing the yellow lever and moving the handlebar up or down (Fig. 7).
Figure 5 Figure 6 Figure 7
12. Have the patient hold the handlebar. This keeps their arms in a SAFE position for transfer.
13. DO NOT transport the patient in a standing position.
14. UNLOCK the rear casters and move the Vista to the location of intended transfer.
15. Once the patient is positioned over the intended area of seating, LOCK the rear WHEELS.
16. Have the patient stand, move the SEATS out and have the patient sit.
17. Once the patient is securely seated (ensure the patient is not seated on the edge of the destination seat!)
UNLOCK rear WHEELS and move the Vista clear of the patient.
18. CLOSE LEGS.

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 12 of 17
VISTA
Operator’s Manual
TECHNICAL SPECIFICATIONS:
PARAMETER SPEC
• SWL 400 lbs
• Device Part Number 51871
• Unit of Measure 1 Each
• Total Weight 92 lbs
• Weight Loose Parts (Footrest) 12 lbs
• Wheels Diameter, Front 3”
• Wheels Diameter, Rear 4”
• Turning Diameter 46.1”
• Leg Under Bed/Stretcher Clearance 3.4”
• Standard Door Width Clearance 23.7”
• Footplate Dimensions 14” x 17” x 14”
• Frame Steel & Aluminum
• FDA Device Class Class 1
• FDA Product Code FSA
• FDA Regulatory Number 880.5510
ENVIRONMENTAL CONDITIONS
FOR SHIPMENT AND STORAGE FOR USE
Temperature 14°F to 104°F (-10°C to 40°C) 41°F to 104°F (5°C to 40°C) ambient
Relative Humidity 20% to 80% non-condensing 20% to 80% non-condensing
Atmospheric Pressure 70 kPa to 106 kPa 70 kPa to 106 kPa
Note: Li-Ion batteries must be stored without exposure to direct sunlight

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 13 of 17
VISTA
Operator’s Manual
PERIODIC MAINTENANCE:
The following scheduled maintenance and inspections will help to ensure trouble-free operation of
your Vista Non-Powered Stand Aid.
Not recommended for use in shower.
Do not pressure-wash the unit.
ONCE A MONTH
• Check for loose or missing nuts and bolts.
• Clean unit – wipe off dust.
TROUBLESHOOTING:
SYMPTOM POSSIBLE CAUSE ACTION
Seat height adjustment does
not release or lock in position
selected.
Release lever is not
functioning properly. Adjust release lever pivots.
Gas spring release cable(s) is
not functioning properly.
Adjust or replace release
cable(s).
Gas spring(s) is not
functioning properly. Replace gas spring(s).

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 14 of 17
VISTA
Operator’s Manual
FACTORY ASSISTANCE:
Expected lifetime: 8-10 years
REPLACEMENT ITEMS:
To order replacement parts, contact Wy’East Medical Customer Service.
Include the following information with your request:
1. Serial and Model numbers of your Vista Non-Powered Stand Aid.
2. Purchase date, if available.
3. Part number and description of the replacement part needed (see “Replacement Parts”
section on page 15 of manual).
4. Shipping and billing instructions, including complete address.
RETURNING ITEMS:
To return parts or goods, contact Wy’East Medical for authorization.
Contact information:
Telephone: (503) 657-3101
Email: customerservice@wyeastmed.com

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 15 of 17
VISTA
Operator’s Manual
51673
51675
51670 51899
51854
51647
51852
51671
51672
51687
51687
REPLACEMENT PARTS:
This manual provides maintenance and service information for the Vista Non-Powered Stand Aid.
If replacement parts are required, contact WY’EAST MEDICAL with the serial number of your Vista
Non-Powered Stand Aid to ensure the accuracy of replacement parts.

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 16 of 17
VISTA
Operator’s Manual
NOTES:

800.255.3126 | wyeastmedical.com
51928 R03 Vista Non-Powered Stand Aid
Operator’s Manual
Page 17 of 17
VISTA
Operator’s Manual
CONTACT INFORMATION
For questions or information regarding other Wy’East Medical products, contact:
Wy’East Medical Corporation
16700 SE 120th Ave.
Clackamas, OR 97015, USA
(503) 657-3101
(800) 255-3126
wyeastmedical.com
info@wyeastmed.com
Table of contents
Other WY'EAST MEDICAL Mobility Aid manuals
Popular Mobility Aid manuals by other brands

Invacare
Invacare O2 Holder Accessory Kit 1488 Installation and operating instructions

Invacare
Invacare 1305L Assembly, installation and operating instructions

Gima
Gima 43162 user manual

liftup
liftup AssiStep installation manual

Medinox
Medinox mx mobility MX79304 Instructions for use

Invacare
Invacare Dolomite Gloss user manual

NRS Healthcare
NRS Healthcare Mowbray M11089 User instructions

Medline
Medline Microban MDS86960KDMB user guide

Harbor Freight Tools
Harbor Freight Tools 62547 Owner's manual & safety instructions

Costway
Costway JH10010 Instruction booklet

Invacare
Invacare 6265E Assembly, installation and operating instructions

ADAPT SOLUTIONS
ADAPT SOLUTIONS SP-CHRG05 installation manual