Wyrestorm EX-35-H2 User manual

18Gbps 4K HDR HDBaseT Extender with
HDCP 2.2 and 2-way PoH
EX-35-H2 Quickstart Guide
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-35-H2 Quickstart Guide | 190509
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Identifying Product Versions
This product was released in 2 different versions which contain different chassis designs and feature sets. The differences are identied throughout this
document in order to make installation and use easier.
Versions can be identied by a v# after the model number on the product chassis model number sticker. Note that version 1 of this product may not contain a
v1 after the product while all version 2s will contain a v2 after the model number.
Operational Differences
Feature Version 1 Version 2
RS-232 Mode Switch Yes No – Changes made this switch unnecessary
3840x2160p @60Hz 10bit 4:2:0 HDR
4096x2160p @60Hz 8bit 4:4:4 Not Supported on Category Cable (HDBaseT) Supported on Category Cable (HDBaseT)
Basic Wiring Diagram
IMPORTANT! Installation Requirements
• This product was released in 2 different versions which contain different
chassis designs and feature sets.
• See Identifying Product Versions for details.
• Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
• Read through the Wiring and Connections section for important wiring
guidelines before creating or choosing premade cables.
• While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
In the Box
1x EX-35-H2 Transmitter
1x EX-35-H2 Receiver
1x 18V DC 1A Power Supply (US/UK/EU)
2x 3-pin Screw Down Phoenix Connectors
1x IR Emitter
1x IR Receiver
4x Mounting Brackets (2x for TX | 2x for RX)
1x Quickstart Guide (this document)
HDMI
HDMI
IR Emitter
IR Emitter
IR Receiver
18V DC 1A
Power Supply
IR to Control System
CAB-IR-LINK (Sold Separately)
EX-35-H2 Transmitter (TX) EX-35-H2 Receiver (RX)
4K/UHD HDMI Source 4K/UHD HDMI Display
KEY
HDMI
HDBaseT Cat6/7
IR TX and RX
Power
HDBaseT
Cat5e/6/6a/7
Note: Extender set may be powered
by either the TX or RX. Only one
power supply is required.

Front Panel (TX/RX) Rear Panel (TX/RX)
Power LED Solid: The receiver is powered On
Off: The receiver is powered Off
Status LED Flashing: The receiver is operating normally.
Off: The receiver is Not operating normally.
HDCP LED
Solid: HDCP content is present.
Flashing: HDCP content is not present.
Off: No signal.
LINK LED
Solid: Link to receiver has been established.
Flashing: Link to receiver has not been
established.
RS-232 Mode
Version 1 Only
Switches the mode for the RS-232 port.
Normal: RS-232 HDBaseT pass-through.
Update: RS-232 rmware update.
Power In
5.5mm Screw Down Barrel Jack
Connect to the included 18V DC 1A power
supply. to the transmitter. A power supply
is not required on the receiver as it will be
powered using PoH.
See Power Supply Wiring for important
information.
HDBT In
HDBT Out
8-pin RJ-45 female
Connect the transmitters HDBT Out to
receivers HDBT In.
IR TX
IR RX
IR TX - 3.5mm (1/8in) Mono Jack: Connect
to the supplied IR emitter to control a local
device from the remote display location via
HDBaseT.
IR RX - 3.5mm (1/8in) Stereo Jack: Connect
to the supplied IR receiver to send IR to the
remote display location via HDBaseT.
See IR TX/RX Guidelines for more
information.
RS-232 1x RS-232: 3-pin Phoenix
HDMI In
HDMI Out
19-pin type A HDMI female
Supports HDMI and DVI/D with adapter
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-35-H2 Quickstart Guide | 190509
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
2 of 4
ABC D
Version 2 Front Panel
A B C D E
Version 1 Front Panel
Version 2 Rear Panel
A B C D E
A B C D E
Version 1 Rear Panel

Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-35-H2 Quickstart Guide | 190509
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
3 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
IR TX/RX Guidelines
• Using WyreStorm infrared emitters and receivers is the best way to ensure
that most IR coding formats are transmitted and received by the NetworkHD
system. Other 3rd party emitters and receivers can be used; however, these
devices must operate in the same manner as the WyreStorm devices.
• Due to differences in IR across 3rd party control systems their IR ports
should never be connected directly to a NetworkHD system as an
incompatibility may exist. WyreStorm offers a cable that compensates for
voltage differences as well adjusts for differences in the pins used within the
port. Refer to the CAB-IR-LINK product page for more information.
IR TX Port Pinout
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
Tip: Anode
Sleeve: Cathode (IR Signal)
IR RX Port Pinout
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
Tip:
Ring: IR Signal
+5V DC
Sleeve: Ground (GND)
RS-232 Wiring
The EX-35-H2 uses a 3-pin RS-232 with no hardware ow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary from
device to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
3rd Party Device
Pin 1 TX (Transmit) ---> To ---> RX (Receive)
Pin 2 RX (Receive) ---> To ---> TX (Transmit)
Pin 3 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector
RS-232 Mode Settings
The RS-232 connector is used to transmit RS-232 over HDBaseT to the remote
location and for rmware updates. Ensure that the RS-232 Mode switch in
the proper position for the operation being performed. This connection is only
available on version 1 of this product.
Set the mode switch to Normal to transmit RS-232
signals from the TX to the RX for controlling devices
in the remote location.
Set the mode switch to the Update position to install
a rmware update in either the TX or RX.
Power Supply Wiring
The EX-35-H2 can supply power from the transmitter to the receiver using PoH on the same category cable that transmits audio and video. The included power
must be connected to the transmitter in order to power the receiver. Should distance of the category cable or other factors prevent PoH from being used,
connect an 18V DC 1A power supply to both devices. Additional power supplies may be purchased from WyreStorm.

Specications
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-35-H2 Quickstart Guide | 190509
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
4 of 4
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that all HDMI and HDBaseT connections are not loose and are
functioning properly
• Verify that the HDBaseT cable is properly terminated following EIA568B
standard
• Verify that the output resolution of the source and display is supported by
this extender
• Congure EDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3rd party Device Control
• Verify that the IR and RS-232 cables are properly terminated following the
Wiring and Connections section.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
Audio and Video
Transmitter Receiver
Inputs 1x HDMI In: 19-pin type A 1x HDBT In: 8-pin RJ-45 Female
Outputs 1x HDBT Out: 8-pin RJ-45 Female 1x HDMI Out: 19-pin type A
Output Video Encoding HDBaseT Class B
Encoding Data Rate 9.2Gbps
End to End Latency (Max) 10μs (micro seconds)
Audio Formats 2ch Analog/PCM | Multichannel: LPCM
Video Resolutions (Max)
Video Resolution HDMI Cat6 Cat6a/7
v1/2 v1 v2 v1 v2
1920x1080p @60Hz 12bit 15m/49ft 70m/230ft 70m/230ft 70m/230ft 70m/230ft
1920x1080p @60Hz 16bit 7m/23ft 70m/230ft 70m/230ft 70m/230ft 70m/230ft
3840x2160p @24Hz 10bit 4:2:0 HDR 3m/10ft 35m/115ft 35m/115ft 35m/115ft 35m/115ft
3840x2160p @30Hz 8bit 4:4:4 7m/23ft 35m/115ft 35m/115ft 35m/115ft 35m/115ft
3840x2160p @60Hz 10bit 4:2:0 HDR 3m/10ft NA 35m/115ft NA 35m/115ft
4096x2160p @60Hz 8bit 4:2:0 7m/23ft 35m/115ft 35m/115ft 35m/115ft 35m/115ft
4096x2160p @60Hz 8bit 4:4:4 7m/23ft NA 35m/115ft NA 35m/115ft
Supported Standards DCI | RGB | HDR | HDR10 | Dolby Vision up to 30Hz | HLG | BT.2020 | BT.2100
Maximum Pixel Clock HDMI: 600MHz | HDBaseT: 297MHz
Communication and Control
HDMI HDMI 2.0 | HDCP 2.2 | EDID | CEC Pass-through | DVI/D supported with adapter (not included)
HDBaseT HDMI 2.0 | HDCP 2.2 | EDID | 2-way PoH | Bidirectional IR and RS-232
CEC CEC Pass-through – Requires CEC compatibility between source and display
IR 1x IR TX 3.5mm (1/8in) Mono | Bidirectional over HDBaseT | 1x IR RX 3.5mm (1/8in) Stereo | Bidirectional over HDBaseT
RS-232 1x 3-pin Screw Down Phoenix Connector | Bidirectional over HDBaseT
Power
Power Supply 18V DC 1A
PoH 48V 15.4W
Max Power Consumption 8.88W
Environmental
Operating Temperature 0 to + 45°C (32 to + 113 °F), 10% to 90%, non-condensing
Storage Temperature -20 to +70°C (-4 to + 158 °F), 10% to 90%, non-condensing
Maximum BTU 30.30 BTU/hr
Dimensions and Weight
Version 1 Version 2
Rack Units/Wall Box <1U <1U
Height 17mm/0.67in 15.2mm/0.6in
Width 140mm/5.52in 136.4mm/5.38in
Depth 90.2mm/3.563in 74.2mm/2.93in
Weight 0.36kg/0.79lbs 0.22kg/0.48lbs
Regulatory
Safety and Emission CE | FCC | RoHS | RCM
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.